LINCOLN CONTINENTAL 1997 Owners Manual

158Checking that the seat is secure
8. Double check that the retractor is in the
automatic locking mode. Try to pull more belt
out of the retractor. If you cannot, the belt is
in the automatic locking mode. See Figure 8.
File:06fnssc.ex
Update:Mon Jun 17 14:19:23 1996

159
Checking the retractor
9. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 6 through
8.
NOTE:To remove the retractor from automatic
lock mode, allow seat belt to retract fully to its
stowed position and the retractor will automatically
switch back to the vehicle sensitive locking mode
for normal adult usage.Installing a Child Safety Seat at the
Front Center Seating Position with
Adjustable Lap Belt1. Lengthen the lap belt. To lengthen the belt,
hold the tongue so that its bottom is
perpendicular to the direction of webbing while
sliding the tongue up the webbing.
2. Place the child safety seat in the center seating
position.
File:06fnssc.ex
Update:Mon Jun 17 14:19:23 1996

160
3. Rout ethe tongu ean dwebbin gthroug htheWARNING
Carefull yfollo wallof the

161
Tether anchorage hardwareAll vehicles include a tether anchor installed at the
rear center seating position for use with child safety
seats. Attachment holes (at each rear outboard
seating position) have been provided in your vehicle
to attach anchor hardware, if required. Additional
kits can be obtained and installed at no charge from
any Ford or Lincoln-Mercury dealer.Tether strap anchorage locations (rear
center seating position only)Refer to Figures 1 and 2.
The tether strap anchorage bracket for the rear
center seating position was factory installed and is
located directly beneath the rear window trim
panel, which is behind the rear seat back. To use
this anchorage, do the following:
1. Open the hinged cover located at the front of
the high mount stop light. This cover conceals
the tether strap anchor bracket, as shown in
Figures 1 and 2.NOTE:Do not raise the hinged cover of the trim
panel beyond its limit, to prevent damage to the
hinge.
Figure 1
File:06fnssc.ex
Update:Mon Jun 17 14:19:23 1996

162
2. Instal lth e tethe rstra pbracke tlocate ddirectlySafet yBelt sfo rChildren
WARNING
If safet ybelt sar e no tproperl yworn

163
WARNING
Do no tus ea belt-positionin gbooster
WARNING
Childre nshoul dalway srid ewit hthe

165
Starting
Fuel-InjectedEngines
WARNING
Do no tstar tyou rvehicl ein aclosed

1663. Make sure that the gearshift is in P (Park) and
the parking brake is set before you turn the
key.
Before you start your vehicle, you should test the
warning lights on the instrument panel to make
sure that they work. Refer to theInstrumentation
chapter.Starting Your EngineTo start your engine:
1. Follow the steps underPreparing to Start Your
Vehicleat the beginning of this section.
2. Turn the ignition key to the ON position.
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.4. Turn the key to the START position (cranking)
until the engine starts. Allow the key to return
to the ON position after the engine has started.
If you have difficulty in turning the key, rotate
the steering wheel slightly because it may be
binding.
For a cold engine:
q
At temperatures10ÊF(-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do
not flood the engine, then try again.
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
File:08fntoc.ex
Update:Mon Jun 17 14:19:30 1996

167
For a warm engine:
q
Do not hold the key in the START position for
more thanfive (5) secondsat a time. If the
engine does not start within five (5) seconds on
the first try, turn the key to the OFF position.
Wait a few seconds after the starter stops, then
try again.
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the parking
brake. Slowly release the brake pedal and drive
away in the normal manner.
NOTE:Your vehicle has an interlock that
prevents you from shifting out of P (Park) unless
your foot is on the brake pedal.If the engine does not start after two attempts:
1. Turn the ignition key to the OFF position.
2. Press the accelerator all the way to the floor
and hold it.
3. Turn the ignition key to the START position.
4. Release the ignition key when the engine starts.
5. Release the accelerator gradually as the engine
speeds up.
If the engine still does not start, the fuel pump
shut-off switch may have been activated. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchin the index.
File:08fntoc.ex
Update:Mon Jun 17 14:19:30 1996

168
Acompute rsyste mcontrol sth e engine' sidle
WARNING
Extende didlin gat hig hengin espeeds
WARNING
Do no tpark ,idle ,or driv eyou rvehicle