battery MAZDA 323 1992 Workshop Manual Suplement

..,. .
a
._
GI CAUTKN
PRECAUTIONS TO TAKE WHEN SERVICING AN ELECTRICAL SYSTEM l Note the following items when servicing the electrical system.
l Do not alter the wiring or electrical equipment in any way; this may damage the vehicle or cause a fire
from short-circuiting a circuit or overloading it.
l The negatrve (-) battery cable must be removed first and
rnstalled last. l Do not reptace with fuses exceedrng specified capacity
Cautron
l 8e sure that the ignitton and other switches are off
before disconnectrng or connecting the battery cables.
Failure to do so may damage the semrconductor
components. Caution l Repfacing a fuse with one of a larger capacrty than
desrgnated may damage components or cause a frre.
l Secure harnesses with provrded clamps to take up slack. l Tape areas of the harness
that may rub or bump l When mounting
components, be sure the
against sharp edges to
protect rt from damage. harness IS not caught or
damaged.
Caution
l Clamp all harnesses near vibratrng components (for
example, the engine) to remove slack and to prevent
contact resultrng from vibration. i Drsconnect heatsensitive l Make sure that the
parts (for example, relays
and ECU) when performing connectors are securely
connected when installed.
l Do not handle electrical components roughly or drop
them. maintenance (such as
weldrng) where
temperatures may exceed
80°C [176OFj.
-*
HI

:
.
GI CAUTION
USING ELECTRICAL MEASURING EQUIPMENT
Use Handling precautions Operation Equpment
Test lamp Test to find open or shorted
crrcuits
l Connect the test lamp
between the circuit being
measured and a ground.
l The lamp will lrght if the
circurt is energized to the
point testedA
l Test lamps use 12V t.4W or
3.4W bulbs or light-emitting
diodes (LEOs). Using a
large-capacity bulb may
damage :he Ckil.
Jumper wrre Used to create a temporary
ctrcult . Connect the jumper wire
between the terminals of a
cjrcurt to bypass a switch. l 00 not connect the lumper
wrre from the power source
line to ground; this may
cause burning or other
damage to harnesses or
electrontc components.
Voltmeter Used for measuring the voltage
of a circutt to find possible
opens or shot-k.
l Connect the voltmeter in
parallel wrth the cjrcurt.
l Set the range to the dewed
voltage.
l Use the service hole when measuring the voltage at the
diagnosis connector.
l Connect the positive (+)
probe to the point where
voltage IS to be. measured
and the negatrve (-) probe to
a ground.
l Tie a thin wire to the
posrtive (+) probe to access
narrow terminals.
Ohmmeter Used to find opens and shorts
In the ctrcurt, to confrrm
contrnurty and to measure
reststance.
l Zero the ohmmeter. l Zero the meter after
switching to the measuring
range.
l Before using the ohmmeter,
make sure the ignitron
switch is off or the megatrve
(-) battery cable is
disconnected to prevent
burning or otherwise
damaging the ohmmeter. &--- l Verify that voltage IS not
applied to the circuit
l Connect the probes between
two points in a Circuit.,
t I t
+ Connect the ammeter in
series with the circuit by
touchtng the positive ( +)
probe to the power-srde
terminal and the negative (-
probe to the ground-srde
terminal. Ammeter
Used to check alternator output,
current supplied to the starter.
and dark current wrthrn a circutt. l Set the range to the desired
amperage.
l Connect the ammeter In
series with the circuit. The
ammeter may be burned or
otherwise damaged if it IS
connected in parallel. Note
Dark current IS the constant flow
of current whrle
the ignitron
switch is OFF.
13EGIX-31;
Gl-t 6

A PRE-DELIVERY INSPECTION TABLE
PRE-DELIVERY INSPECTION TABLE
[EXTERlORI
INSPECT and ADJUST, of necessary. the followlng Items to
specrfrcatron:
0 Glass, exterior bright metal and paint for damage
0 Wheel lug nuts
0 Tire pressures
0 All weatherstrips for damage or detachment
0 Operation of bonnet release and look
0 Operation of trunk Ild, hatch and fuel lbd opener
(of equipped)
0 Door operation and alignment
0 Headtrght aiming
INSTALL the foltowrng parts
0 Wheel caps or rrngs (if equipped)
0 Outsrde mirror(s)
1 UNDER BONNET-ENGINE OFF j
INSPECT and ADJUST. If necessary, the following items to
specrflcatlon.
0 Fuel, coolant and hydraulic tines, fittings, connectlons and
components for leaks
0 Engine 011 level
0 Power steering fluid level (of equipped)
0 Brake master cylinder fluky levels
0 Clutch master cylinder fturcl levels (If equipped)
0 Wtndshreld washer reservojr flurd level
0 Radiator coolant level and specrfic gravity
0 Tightness of water hose clamps
0 Tightness of battery terminals, electrolyte level and specific
gravity
0 Manual transaxle oil level
0 Drive belt(s) tension
Cl Carburetor lrnkage (choke control, wrde open throttle posi-
tion. etc ) (carburetor model only)
q Accelerator cable and linkage for free movement
0 Headlight cleaner and flurd level (if equipped)
BLEED air from fuel line (diesel engrne only)
CLEAN the spark plugs (except for diesel engine)
piEi6F]
INSTALL the following parts
0 Rubber stopper for rnsrde rear view mirror (if equjpped)
0 Fuse for accessories
CHECK the operation of the following items.
0 Seat controls (sliding and reclining) and head rest
0 Seat belts and warning system
Cl Ign&on switch and steering lock
0 Power window (if equipped)
D Door tacks including child proof door locks
Cl Inhibitor switch (ATX only)
Cl All Ikghts rncluding warning and Indicator lbghts
0 Ignition key reminder buzzer (If equipped)
A-Z
0 Horn, wbpers and washers (front and rear, If equipped)
0 Antenna (tf equipped)
0 Cigarette Ibghter and clock (if equipped)
0 Remote control outside mirror (if equrpped)
0 Heater, defogger and air conditioner at various mode selec-
tions (if equlppedj
0 Sunroof (If equipped)
CHECK the following items
0 Presence of spare fuse
0 Upholstery and Interior finish
CHECK and ADJUST, If necessary, the followjng items:
IJ Operation and fit of windows
0 Pedal height and free play of brake and clutch pedal
0 Parking brake UNDER BONNET-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
0 Operation of Idle-up system for air condbtroner or power steer-
ing (if equrpped)
0 Automatic transaxle flurd levet
0 tnltial ignrtlon timing (except disel engine)
0 Idle speed
0 Operation of throttle positron. sensor (EGI engrne)
0 Operation of cold start device and glow plug warning light
(diesel engine only)
0 Operation of dash pbt (EGI.engine)
fTiGGJ
CHECK the following items.
0 Underside fuel, coolant and hydraulic Irnes, ftttlngs, connec-
tions and components for leaks
0 Trres for cuts or brurses
0 Steering Itnkage, suspensron, exhaust system and all under-
side hardware for .looseness or damage 1 ROAD TEST j
CHECK the following items
0 8rake operation
0 Clutch operation
0 Steering control
!ZI Operation of meters and gauges
Cl Squeaks, rattles or unusual noises
Cl Engine general performance
0 Emergency locking retractors 1 AFTER ROAD TEST ]
REMOVE the seat and floor mat protective covers
CHECK for the necessary owner information materials, took
and spare tire
m vehicle
93EOAX-002
-- MAIN Char3 t: In
A: PC R: F!t T: Ti! Emis! The ed : to t!

A SCHEDULED MAtNTENANCE SERVtCES (Europe)
Maintenance Number of months or km (miles), whichever comes first
Months” - 6 12 18 24 30 36 42 48
Kllometers 1,000 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000
{Miles)
(600) (6,000) f[t2,000) (18,000) (24,000) (3U,OOO) (36,000) (42,000) {48,000), Engine
Intake and exhaust manrfold nuts (Bolts)
Drive belts”
i Engine trmlng beltW3
Engine oil (Turbo)‘4
01 filter
l *
Cool!ng system (Includtng
coolant level adlustment)
Engrne coolant T T T
A A A
A A
Replace every 100,000 km (60,000 miles)
Replace every 5,000 km (3,000 miles) or 6 months
R R R R R 1 R R R
I I I I
I
Replace every 2 years Fuel system
Idle speed
Air cleaner element * 5
Fuel
falter
Fuel Ilnes and hoses Ignition system
A f 1
I R I R
R R
I I f t I ~
lnlttal rgnrtloh trmlng 1 I I I I I I I I
Spark plugs A
A. A A
Spark plugs (Only for Sweden) Adjust every 30.000 km (t8.000 mrls) Evaporative emission control system
Throttle sensor Throttle sensor (Only for Sweden)
Evaporative system
Evaporatrve system (Only for Sweden) 1 A 1 1 A 1 1 A 1 ) A
Adjust every 80,000 km (48,000 miles)
1 I 1 1 I’ 1 1 I 1 1 I
Inspect every 80,000 km (48,000 mites) Electrical system
Battery electrolyte level and specific gravity 1 I f I I I
All Electrical system
l ’ 1 I
I 1 I I I
1 . 1 I I
Headlight alrgnment 1 A A A . A. Chassis and body
t 3EOAX-303
A-4 Chas
SW31 Rear
Tires
Hing
Seat

SELF-DIAGNOSIS FUNCTION F3 I
Open or short crcuit
13EOFS322
Caution l If there is more than one failure present, the code numbers will be indicated in numerical or-
der, lowest number first.
l After repairing a failure, turn off the ignition switch, disconnect the negative battery cable,
and depress the brake pedal for at least twenty seconds to erase the service code from the
ECU memory. II
F3-17

F3 SELF-DIAGNOSIS FUNCTION
:ODE NO. 25 {SOLENOlD VALVE - PRESSURE REGULATOR CONTROL) (Low temperature opoeration)
INSPECTION ACTION
Disconnect connector from ECU; IS there battery Yes Check ECU termrnal connector for poor
voltage at ECU terminal 2T (G/C) wrth Ignition connection
switch ON?
4 If OK, replace ECU
CT page F3-2
c3 If not OK, repatr or replace connector
NO Go to next step
2 In same condition as rn Step 1. is there battery Yes Repair or replace wlrrng harness (G/O)
voltage at sofenord vatve (PRC low temp.) con-
nector termrnal wrre (G/O)?
NO Go to next step
3 Is solenord valve (PRC low temp ) UK7 Yes Check for a short or open crrcuit in WII-
CT page F343 ing harness (main relay [FUEL INJ re-
lay] - solenoid valve [PRC low temp.])
NO Replace solenord valve (PRC tow temp.)
1
t3EOF3-323
CODE NO. 35 (SOLENOID VALVE - PRESSURE REGULATOR CONTROL) (High temperature opoeration)
STEP lNSPECTlON ACTlON
1 Disconnect connector from ECU: is there battery Yes Check ECU terminal connector for poor
voltage a? ECU terminal 22 (G) with rgnttlon connection
swttch ON7
4 If OK, replace ECU
J page F3-2
e If not OK, repair or replace connector
No Go to next step
2 In same condrtron as In Step 1, is there battery Yes
voltage at solenoid valve (PRC high temp.) con- Repair or replace wiring harness (G)
nector terminal wire (G)?
No Go to next step
3 Is solenoid valve (PRC high temp ) OK7 Yes Check for a short or open circuit In wir-
r;r page F343 ing harness (marn relay [FUEL INJ re-
WI - sofenord valve [PRC high temp.])
No Replace solenoid valve
(PRC high temp.)
f3EOF3-324
Circuit Diagram
ECU
I
2T 22 I
G
TO MAIN RELAY
I SOLENOID
VALVE
(PRC HIGH TEMP.)
F3-18 :3EOf3 32 5
--
TRW
RELAT
c
-..


INPUT
--
KNOCH
--
DIAGM
(TEN T
--
IGNITIi
(STAR1
--
E/L SIC
-a
P/S PR
--
A/c SYI
--
NEUTR
SWITCI
--
STUPb
--
ATMDI
SENSQ
-a
THRUI
-..
INfAk.1
--
AlFlFLC
--
UXYGE
--
WATEF
--
DlSfRl

F3 TROUBLESHOOTING GUIDE
SYMPTOM TROUSLESHOOTING
2 . CRANKS NORMALLY BUT WILL NOT START (NO COMBUSTION)
LIESCRIP-
l Engine cranks at normal speed but shows no sign of firing l Battery in normal condition
TION *Throttle valve not held fufly open while cranking (dechoke system not operating}
l Fuel in tank
UROOBLESHUOTlNG HINTS]
@ No spark
@.I low fuei tine pressure
l Ignition control malfunction @I Low engine compresslon l Ignition system component malfunction
@ No fuel injection
l Fuel pump inoperative l Ihjectors inoperative
;TEP
INSPECTION
I ACTION
1
Is strong btue spark visible at disconnected high- Yes Go to Step 3
tension lead?
NO Go to Step 2
2 Is “00” dlsplayed on Self-Dlagnosjs Checker
Yes
with ignltron switch ON? Check rgnltion system (Refer to
Troubleshooting “Misfire”)
c7 Section G
SYSTEM SELECT: 1 No
Service Code No. displayed Check for cause (Refer to specified
check sequence)
G- page
F3-16
“66” flashes
Check ECU termrnal 1F voltage
3 page W-45

Voltage: Battery vabage
(ignition switch ON)
W: SELF TEST C+ If OK, replace ECU
4 If not OK, check wiring
CT page F3-2
(ECU
- Self-Diagnosis Checker)
3
Connect diagnosis connector terminals F/P and
Yes
GND with jumper wire; IS fuel pump operating Does engine start in this condition?
sound heard wjth ignition switch ON?
4 If it does, check circuit-opening
relay
4 If it does not, go to Step 5
No Go to next step
F3-22
iTEF
6
8

TROUBLESHOOTING GUIDE F3
4 CRANKS NORMALLY 8UT WILL NOT START (PARTfAL COMBUSTION) - AFTER WARM-UP
&RIP-
l Engine cranks at nurmal speed and shows partial combustion but will not Continue running after being hot
soaked
FION
l Battery in normal condltlon
*Engine starts normally when cold
TROUBLESHOOTING
HINTS] 3 Air/Fuel mixture too rich @ Vaporlock
ssure not held in fuel line after engrne IS
GND mth jumper wire tor 3
minutes with ignition
Fuel
line pressure: 265-314 kPs (2.7-3.2 kgflcm2, 38-46 psi 1
c3 If pressure
quickly increases,
check pressure regulator
4 If pressure
gradually increases,
check fuel line and filter lor
clogging
If hose is not clogged. check fuel
pump maximum pressure
High pressure Check if fuel return hose is clogged or
restricted
INSTALL CLAMPS e If rt is not, replace pressure
regulator
@ It It 6. repalr or replace it CT page F3-3
F3-25

F3 TROUBLESHOOTING GUIDE
I- STEP lNSPECTlON ACTION
Yes Go to Step 8
5 In same condition as in Step 2, IS fuel ilne pres-
sfire held after Igrxtbon swatch rs turned OFF?
Fuel line pressure: More than 147 kPa
Il.5 kgflcm’, 21 Psi 1 for 5 min.
6 In same condition as in Step 3, IS fuel line pres-
sure held after lgnltron switch IS turned OFF?
Fuel line pressure: More than 147 kPa
{ t.5 kgf/cm*, 21 psi) for 5 min.
No
I Go to next step
Plug both vcuum ports of pressure regulator; IS
fuel lme pressure held after ignltlon switch is
turned OFF? Yes Replace pressure regulator
r~ page F3-3
Fuel line pressure: More than 147 kPa
{ 1.5 kgf/crn*, 21 psi] for 5 min.
NO Check fuel pump hold pressure
e If OK, check InJector for fuel
leakage
e If not OK reptace fuel pump ZF- page F3-42
T page F3-3
8 Dlscofinect water thermosensor connector, does
engtne start? Yes Check water thermosensor
e ff OK. check connectrons of water
thermosensor and ECU 2Q terminal
Q If not OK, replace water thermo-
sensor
ET page F3-13
No 1 Go to next step --~
Is “00” drsplayea on Self-Diagnosis Checker
with ignition switch ON? 9 Yes Go to next step
NO Service Code No. displayed
Check for cause (Refer to specified
check sequence)
c7 page F3-16 SYSTEM SELECT, 1
“88” flashes
Check ECU terminal IF voltage
KIT page F3-45
Voltage: Battery voltage
(ignition switch ON)
e If OK, replace ECU
ET- page F3-2
e If not OK, check wiring
(ECU - Self-Diagnosis Checker)
Y %EtECT SW: A
Yes 1 Go to next step 10 Are rf ECU termrnaf voltages are OK?
(especjaffy 1C. 2D. and 2Q)
CT page F3-45
NO Check for cause
Yes Replace ECU
=T page F3-2
No Change to another brand of fuel
13EOF3 331 Try known good ECU, does condition improve?
CT page F3-2
F3-26

TROUBLESHOOTING GUlDE F3
7 CRANKS NORMALLY BUT HARD TO START - AFTER WARM-UP
*
l Engrne cranks at normal speed but requkres excessive cranking time before starting after running and being
DESCRIP- hot soaked
TION
l Battery rn normal condition l Engine starts normatly when cold
*Engine runs normally at Idle (If idle condrtron is not OK, refer to “Rough idle” ~Nos. 8-l 21)
[ ~ROUBLESHOOTLNG HINTS1
[ i 5 ArrlFuel mixture too Rich - l Fuel rqection control malfunction l lnpector fuet leakage
I
TEP tNSPECTlON @ Vaporlock
l Fuel pressure not held rn fuel line after engrne IS
stopped
l Pressure regulator control system malfunction
I ACTION
1 Is “00” dispiayed on Self-Diagnoses
Checker wrth rgnrtron switch ON7
SYSTEM?_SELECT. 1
SELECT SW. A
Remove vacuum hose from pressure regulator
(port A) ancI plug rt. dOt?S engine start normally’-,
Remove both vacuum hoses from pressure regu-
lator (ports A and Bj and plug them; does en-
gine start normally7
@
PtUG
/ /
Are ECU terminal voltages OK
(especially 1 C, 20, 20 and 2T)?
w page F3-46 Yes Go to next step
No Service Code No. displayed
Check for cause (Refer to specified
check sequence) CT oaae F3-16
“88” flashes
Check ECU terminal 1F voltage
Voltage: Battery voltage
(ignition switch ON) w page F3-45
( cs> It OK. replace ECU
/ w page F3-2’
3 If not OK, check wlrtng
(ECU - Self-Dlagnosrs ChecKer)
Yes Check pressure regulator control sys-
.
tern (high temperature operation) w page F3-43
I NO Go to next step
Check pressure regulator control sys-
tem (low temperature operation)
No 1 Go to next step
Yes Go to next step
NO Check for cause
F3-27