timing belt MAZDA 626 1987 Owners Manual

5
ENGINE ELECTRICAL SYSTEM
OUTLINE 5— 2
STRUCTURAL VIEW 5— 2
SPECIFICATIONS 5— 5
TROUBLESHOOTING 5— 7
BATTERY 5— 8
INSPECTION 5— 8
RECHARGE. 5— 8
SPARK PLUG 5— 9
REMOVAL AND INSTALLATION 5— 9
INSPECTION 5— 9
IGNITION COIL 5—10
INSPECTION 5—10
HIGH-TENSION LEAD 5—10
INSPECTION 5—10
DISTRIBUTOR 5—11
SPARK TEST 5—11
IGNITION TIMING 5—11
SPARK CONTROL 5—12
REMOVAL 5—14
DISASSEMBLY 5—15
INSPECTION 5—16
ASSEMBLY 5—17
INSTALLATION 5—18
H.E.I. TROUBLESHOOTING 5—19
IGNITER (FE DOHC) 5—20
INSPECTION 5—20
ALTERNATOR 5—21
CROSS SECTIONAL VIEW 5—21
CHARGING SYSTEM 5—22
TROUBLESHOOTING 5—23
REMOVAL 5—27
DISASSEMBLY 5—28
INSPECTION 5—32
ASSEMBLY 5—35
INSTALLATION 5—36
V-BELT TENSION 5—37
STARTER (GASOLINE ENGINE
0.85, 0.95 KW TYPE) 5—38
STARTING SYSTEM CIRCUIT 5—38
ON-VEHICLE INSPECTION 5—38
REMOVAL AND INSTALLATION 5—39
DISASSEMBLY AND ASSEMBLY 5—39
INSPECTION 5—40
PERFORMANCE INSPECTION 5—43
STARTER
(GASOLINE ENGINE, 1.4 KW TYPE) 5—45
STARTING SYSTEM 5—45
ON-VEHICLE UNSPECTION 5—45
REMOVAL 5—46
DISASSEMBLY 5—46
INSPECTION 5—49
ASSEMBLY 5—53
CHECKING OPERATION 5—54
INSTALLATION 5—55
STARTER
(DIESEL ENGINE, 2.0 kW TYPE) .... 5—56
STARTING SYSTEM CIRCUIT 5—56
ON-VEHICLE INSPECTION 5—56
REMOVAL AND INSTALLATION 5—57
DISASSEMBLY AND ASSEMBLY 5—57
INSPECTION 5—61
PERFORMANCE INSPECTION 5—64
STARTER
(DIESEL ENGINE, 2.2 kW TYPE).... 5—66
STARTING SYSTEM CIRCUIT 5—66
ON-VEHICLE INSPECTION 5—66
REMOVAL AND INSTALLATION 5—67
DISASSEMBLY AND ASSEMBLY 5—67
INSPECTION 5—71
PERFORMANCE INSPECTION 5—74
QUICK START SYSTEM (QSS) 5-76
COMPONENT LOCATION 5—76
CIRCUIT DIAGRAM 5—76
SYSTEM OPERATION 5—77
TROUBLESHOOTING GUIDE 5—78
CONTROL UNIT 5—79
GLOW PLUG RELAY 5—80
BLOW PLUG 5—80
WATER TEMPERATURE SWITCH.... 5—80
76g05x-001

OUTLINE 5
SPECIFICATIONS
Gasoline Engine
item
Engine
F6 F8 FE
(8 VALVE)
FE (12 VALVE) FE
(DOHC)
Battery
Voltage
Type and capacity
12. Negative ground
(20 hour rate) 34B19L(S) (33 Ah): General 50D20L (50 Ah), 55D23L (60 Ah): ECE
Alternator
Type A.C.
Output V-A 12-70
Regulator type Transistorized (built-in IC regulator)
Regulated voltage 14.1-14.7
Brush length
mm (in) Standard 16.5 (0.650)
Minimum 8.0 (0.315)
Drive belt tension
mm (in)/98 N (10 kg, 22 lb) New: 6-8 (0.24-0.32), Used: 7-9 (0.28-0.35)
Starter
Type Coaxial reduction: Middle East & General (FE • carburetor)
Non-reduction: Others
Output V-kW 12-0.85
Brush length
mm (in)
12-0.95
Standard 17.0 (0.669)
Minimum 11.5 (0.453)

Unleaded fuel
17.0 (0.669)
Others
17.51
Unleaded fuel 11.5(0.453) Others 10,0 (0.394)

12-1.4 12-0.95
17.0 (0.669)
11.5 (0.453)
Ignition timing 6 ± 10 BTDC (Vacuum hose disconnected)

12
±
1° BTDC
(Test connector

grounded)
Distributor
Type Fully transistorized (HEI)
Electronic spark advance
Centrifugal spark advance
(crank angle/engine speed)
degree/rpm
F6
-2-2/1,000 6-10/2,100 14-18/6,100
F8 -2—2/1,000 10-14/2,100 18-22/6,100
FE (8 VALVE)—Carburetor Unleaded fuel
(MTX)-2—2/1,760 12—16/3,360 22—26/5,320 (ATX)-2-2/1,300 12-16/3,360 22-26/5,320
Others
-2—2/1,460 10—14/2,540 22—26/5,540
FE (12 VALVE)—Carburetor -2-2/1,200 10—14/2,400 10—14/4,000 16-20/5,000
FE—Fuel injection (except FE DOHC) -2—2/1,000 10—14/2,600 10—14/4,600 16—20/5,800
Unleaded fuel model 76G05X-503
5-5

TROUBLESHOOTING GUIDE 5
TROUBLESHOOTING GUIDE
Problem Possible cause Remedy Page
Starter does not turn at all, or Its turning speed Is too slow to start the engine.
Battery and related parts Poor contact of battery terminals Poor grounding of negative cable Voltage drop caused by discharged battery Insufficient voltage caused by battery malfunction
Clean and tighten Clean and repair Recharge Replace
5- 8
5- 8 5- 8
Ignition switch and related parts Poor contact of ignition switch Loose ignition switch wiring or connector Broken wire between ignition switch and magnetic switch
Replace Repair Repair or replace 5-38,45,56,66
Magnetic switch and related parts Loose wiring and/or connectors Burnt magnetic switch contact plate or improper contact Broken wire in magnetic switch pull-in coil Broken wire magnetic switch holding coil
Repair Replace
Replace Replace
5-38,45,56,66 5-43,54,64,74
5-43,54,64,74 5-43,54.64,74
Starter Poor contact of brushes
Fatigued brush spring Poor grounding of field coil Poor soldering of field coil Commutator mulfunction Grounded armature Worn parts
Adjust contact or replace Replace Replace Repair Repair or Replace Replace Replace
5-43,54,64,74
Starting problem Gasoline engine Insufficient battery capacity Malfunction of spark plug (s)
Loose positive terminal Damaged distributor cap or rotor Ignition coil malfunction laniter malfunction
Recharge Clean, adjust or replace Tighten Replace Replace Renlane
5— 8 5— 9
5—16 5—10 5-16,20
Diesel engine Insufficient battery capacity QSS svstem malfunction Recharge ReDlace 5— 8 5-76
Starter turns but pinion gear does not mesh with ring gear
Starter Tip of overrunning clutch pinion is worn Weakened overrunning clutch drive spring Worn overrunning clutch Improper sliding of spline
Worn bushing Worn ring gear
Replace Replace Replace Adjust contact and repair, or replace Replace ReDlace
5-40,54,70
Starter turns continuously (does not stop) Magnetic switch Sticking contact place of magnetic switch Layer shorting coil of magnetic switch Ignition switch does not return
Replace Replace Rfinlanfi
5-43,54,64,74 5-43,54,64,74
Misfiring Dirty or damaged spark plug (s) Malfunction of wiring, or open circuit Damaged distributor cap
Clean or replace Repair or Replace Replace
5- 9 5—10 5—16
Discharging of battery Alternator Loose drive belt Grounded or broken stator coil Broken rotor coil Poor contact of brush and slip ring
Malfunction of rectifier Malfunction of IC regulator Battery and related parts Insufficient or unsuitable battery electrolyte Malfunction of battery electrode (internal short-circuit) Poor contact of battery terminal (s) Excessive electric load
Adjust Replace Replace Clean, repair or replace Replace Replace
Adjust Replace
Clean and tighten Check power consump-tion and short circuit
5-37 5-32 5-32 5-32
5-34
5— 8 5- 8
5— 8
Overcharging of battery IC regulator malfunction Operating in extremely high temperature Replace Reoair
Poor acceleration Mis-adjusted ignition timing Distributor malfunction Adjust Repair or replace 5—11 5—11
Knocking Mis-adjusted ignition timing | Distributor malfunction Adjust Repair or replace 5—11 5—11
76G05X-003
5-7

DISTRIBUTOR 5
7BU05X-075
86U05X-048
76G05X-007
DISTRIBUTOR
SPARK TEST
1. Disconnect the distributor lead from the distributor.
2. Hold it with insulated pliers approx. 5—10 mm
(0.20—0.39 in) from a ground.
3. Crank the engine and check that a strong blue
spark is visible.
4. If there is no spark, the ignition coil or pick-up coil
may be bad.
Check once again after replacing the ignition coil
or pick-up coil.
IGNITION TIMING
1. Warm up the engine to the normal operating tem-
perature.
2. Turn all electric loads OFF.
3. Connect a tachometer and timing light to the
engine.
4. Connect a jumper wire between the test connec-
tor and ground. (Only for FE DOHC)
5. Check the idle speed. Set to the specified speed
if necessary.
Idle speed: 750 ± 50 rpm (FE DOHC)
800 t58 rpm (F6, F8 FE—MTX)
900 i58 rpm (F8, FE—ATX
in "P" range)
950 -5o rmp (F6—ATX
in "P" range)
6. Check that the timing mark (Yellow) on the crank-
shaft pulley and the mark on the timing belt cover
are aligned.
Ignition timing:
FE DOHC: 12 ± 1° BTDC
(Test connector grounded)
Others: 6 ± 1°
(Vacuum hoses disconnected and
plugged)
76G05X-008
5—11

30 TECHNICAL DATA
0. MEASUREMENT
Item Engine model Coupe/MX-6 Sedan Hatchback

Overall length mm (in) 4,450 (175.2) 4,515 (177.8) 4,515 (177.8)
Overall width mm (in) 1,690 (66.5) 1,690 (66.5) 1,690 (66.5)
Overall height (14 inch/13 inch) mm (in) 1,360 (53.5)/1,345 (52.9) 1,410 (55 5)/1,395 (54.9) 1,375 (54.1)/1,360 (53 5)
Wheel base mm (in) 2,515 (99.0) 2,575 (101.4) 2,575 (101.4)
Tread (14 inch/13 inch)
mm (in)
Front 1,455 (57.3)/1,460 (57.5) 1,455 (57.3)/(1,460 (57.5) 1,455 (57.3)/1,460 (57.5) Tread (14 inch/13 inch)
mm (in)
Rear 1,465 (57.7)/1,455 (57.3) 1,465 (57.7)/1,455 (57.3) 1,465 (57 7)/1,455 (57 3)
1
A. ENGINE (SOHC)
12-valve
— Engine model Item FE 12-valve
~vpe
Gasoline, 4-cycle
Cylinder arrangement and number In-line, 4-cylinders
Type
of
combustion chamber Pentroof
Valve system OHC, belt-driven
Bore
x
Stroke
mm (in)
86.0
x
86.0 (3.39
x
3.39)
Total piston displacement
cc
(cu
in)
1,998 (121.9)
Compression ratio 9.5
: 1

Compression pressure
kPa (kg/cm2, psi)-rpm
Standard 1,422 (14.5, 206)—280
Compression pressure
kPa (kg/cm2, psi)-rpm
Minimum 996 (10.2, 144)—280 Compression pressure
kPa (kg/cm2, psi)-rpm Maximum difference
between cylinders 196 (2.0,
28)

Valve timing
IN
Open
BTDC 14°
Valve timing
IN Close ABDC 56° Valve timing
EX Open BBDC 69° Valve timing
EX Close ATDC 13°
Valve clearance
mm (in)
IN 0; Maintenance free Valve clearance
mm (in)
EX 0; Maintenance free

Cylinder head

Heiaht
mm (inl
91.95-92.05 (3.620-3.624)
Distortion
mm (inl
Maximum 0.15 (0.006)
Grinding limit
mm (in)
Maximum 0.20 (0.008)

Valve and valve auide

Valve head diameter
mm (in)
IN 32.4-32.6 (1.276—1.283) Valve head diameter
mm (in)
EX 33.9-34.1 (1.335-1.343)
Valve head thickness (margin)
mm (in)
IN 0.8-1.2 (0.031—0.0471 Valve head thickness (margin)
mm (in)
EX 1.3—1.7 (0.051-0.067)
Valve face angle IN 45° Valve face angle EX 45°
Valve length
mm (in)

IN Standard 115.81 (4.55941
Valve length
mm (in)

IN Minimum 115.31 (4.5398) Valve length
mm (in)
cv Standard 116.21 (4.5752)
Minimum 115.71 (4.55551
Valve stem diameter
mm (in)
IN 6.970-6.985 (0.2744-0.2750) Valve stem diameter
mm (in)
EX 6.965-6.980 (0.2742-0.27481
Guide inner diameter
mm (in)
IN 7.01-7.03 (0,2760-0.2768) Guide inner diameter
mm (in)
EX 7.01-7.03 (0.2760-0.27681
Valve stem
to
guide clearance
mm (in)

IN 0.025-0.060 (0.0010-0.0024)
Valve stem
to
guide clearance
mm (in)
EX 0.030-0.065 (0.0012—0.0026) Valve stem
to
guide clearance
mm (in)

Maximum 0.20 (0.00791
Guide projection (Height "A")
mm (in)
19.8-20.3 (0.780-0.799)

30—2

TECHNICAL DATA 30
" Engine model Item FE 12-valve
Timing belt

Belt deflection
mm
(in)/98
N
(10 kg,
22 lb)
5.5—6.5 (0.22-0.26)

8-valve
Engine model
Item -••--.
FE 8-valve F8
F6
Engine model
Item -••--. ECE Middle
East
General
ECE General F6

Type Gasoline, 4-cycle
Cylinder arrangement and number In-line, 4-cylinders
Type
of
combustion chamber Multispherical
Valve system OHC, belt-driven
Bore
x
Stroke
mm
(in) 86.0
x
86.0 (3.39
x
3.39) 86.0
x
77.0
(3.39
x
3.03)
81.0
x
77.0 (3.19
x
3.03)
Total piston displacement
cc
(cu
in)
1,998 (121.9) 1,789 (109.1) 1,587 (96.8)
Compression ratio 8.6
: 1
9.0
: 1

Compression pressure kPa (kg/cm2, psi)-rpm
Standard 1,275 (13.0, 185)—270 1,128 (11.5, 164)—270
Compression pressure kPa (kg/cm2, psi)-rpm Minimum 893 (9.1, 129)—270 790 (8.1, 114)—270 Compression pressure kPa (kg/cm2, psi)-rpm Maximum difference
between cylinders 196 (2.0,
28)

Valve timing
IN Open BTDC 16° 20° 17°
Valve timing
IN Close ABDC 54° 65° 56° Valve timing
EX Open BBDC 54° 65° 64° Valve timing
EX Close ATDC 16° 20° 15°
Valve clearance
mm
(in) IN 0.30 (0.012) Valve clearance
mm
(in) EX 0.30 (0.012)

Cylinder head

Height
mm (in)
91.95-92.05 (3.620-3.624)
Distortion
mm
(in) Maximum 0.15 (0.006)
Grinding limit mm (in) Maximum 0.20 (0.008)

Valve and valve guide

Valve head diameter
mm
(in) IN 43.9-44.1 (1.728-1.736) Valve head diameter
mm
(in) EX 35.9-36.1 (1.413-1.421)
Valve head thickness (margin)
mm
(in) IN 0.8—1.2 (0.031-0.047) Valve head thickness (margin)
mm
(in) EX 1.3-1.7 (0.051-0.067)
Valve face angle IN 45° Valve face angle EX 45°
Valve length
mm
(in)
IN Standard 111.89 (4.4051)
Valve length
mm
(in)
IN Minimum 111.39 (4.3854) Valve length
mm
(in)
EX Standard 111.69 (4.3972) Valve length
mm
(in)
EX Minimum 111.19 (4.3776)
Valve stem diameter
mm
(in) IN 8.030-8.045 (0.3161-0.3167) Valve stem diameter
mm
(in) EX 8.025-8.040 (0.3159-0.3165)
Guide inner diameter
mm
(in) IN 8.07-8.09 (0.3177-0.3185) Guide inner diameter
mm
(in) EX 8.07-8.09 (0.3177-0.3185)
Valve stem
to
guide clearance
mm
(in)
IN 0.025-0.060 (0.0010-0.0024)
Valve stem
to
guide clearance
mm
(in) EX 0.030-0.065 (0.0012-0.0026) Valve stem
to
guide clearance
mm
(in)
Maximum 0.20 (0.0079)
Guide projection (Height "A")
mm
(in) 19.1-19.6 (0.752-0.772)

30-5

30 TECHNICAL DATA
~ ——Engine model
Item —
FE 8-valve
F8 F6
~ ——Engine model
Item —
Middle ECE East General
F8 F6
Thrust bearing (center main bearing)

Crankshaft end play
mm
(in) Standard 0.08-0.18 (0.0031-0.0071) Crankshaft end play
mm
(in) Maximum 0.30 (0.0118)
Bearing width
mm (in)

Standard 27.94-27.99 (1.100-1.102)
Bearing width
mm (in)
0.25 (0.010) oversize 28.04—28.09 (1.104-1.106) Bearing width
mm (in)
0.05 (0.020) oversize 28.12-28.17 (1.107-1.109) Bearing width
mm (in)

0.75 (0.030) oversize 28.20—28.25 (1.110—1.112)

Timing belt

Belt deflection
mm
(in)/98
N
(10 kg,
22 lb)
|5.5—6.5 (0.22-0 26) 4.0-5.0 (0.16-0.20)

1B. ENGINE (DOHC)
— Engine model FE DOHC
Item ~ Leaded fuel Unleaded fuel

Type Gasoline, 4-cycle
Cylinder arrangement and number In-line, 4-cylinders
Type
of
combustion chamber Pentroof
Valve system OHC. belt-driven
Bore
x
Stroke mm (in) 86.0
x
86.0 (3.39
x
3.39)
Total piston displacement cc (cu
in)
1,998 (121.9)
Compression ratio 10.0
: 1
9.2
: 1

Standard 1,422 (14.5, 206)—290 1,373 (14.0, 199)—310
Compression pressure Minimum 996 (10.2, 144)—290 961 (9.8, 139)—310
kPa (kg/cm2, psi)-rpm Maximum difference
between cylinders 196 (2.0, 28)
IN Open BTDC 10° 10°
Valve timing
IN Close ABDC 60° 55° Valve timing
EX Open BBDC 60° 55° EX Close ATDC 10° 10°
Valve clearance mm (in) IN 0; Maintenance free Valve clearance mm (in) EX 0; Maintenance free

Cylinder head

Heiaht mm (in) 133.95-134.05 (5.274-5.278)
Distortion mm (in) Maximum 0.15 (0.006)
Grinding mm (in) Maximum 0.20 (0.008)
HLA
to
cylinder head clearance mm (in) Standard 0.025-0.066 (0.0010-0.0026) HLA
to
cylinder head clearance mm (in) Maximum 0.18 (0.0071)

Valve and valve guide

Valve head diameter mm (in) IN 33.6-33.8 (1.323-1.331) Valve head diameter mm (in) EX 28.8-29.0 (1.134—1.142)
Valve head thickness (margin)
mm
(in) IN 1.0-1.7 (0.039-0.067) Valve head thickness (margin)
mm
(in) EX 1.1—1.7 (0.043—0.067)
Valve face angle IN 45° Valve face angle EX 45°
IN Standard 103.18 (4.0622)
Valve length
mm (in)

IN Minimum 102.68 (4.0425) Valve length
mm (in)

EX Standard 103.94 (4.0921) EX Minimum 103.44 (4.0724)
Valve stem diameter mm (in) IN 5.970-5.985 (0.2350-0.2356) Valve stem diameter mm (in) EX 5.965-5.980 (0.2348—0.2354)
Guide inner diameter mm (in) IN 6.01-6.03 (0.2366-0.2374) Guide inner diameter mm (in) EX 6.01—6.03 (0.2366-0.2374)
IN 0.025-0.060 (0.0010-0.0024)
Valve stem
to
guide clearance mm (in) EX 0.030-0.065 (0.0012-0.0026)
Maximum 0.20 (0.0079)
| Guide projection (Height "A") mm (in) 11.4-11.9 (0.449-0.469)

30-8

30 TECHNICAL DATA
~ ———Engine model
Item ~ . _
FE DOHC ~ ———Engine model
Item ~ . _ Leaded fuel Unleaded fuel

End gap measured
in
cylinder
mm
(in)
Top 0.20-0.35 (0.008-0.0138)
End gap measured
in
cylinder
mm
(in) Second 0.15-0.30 (0.006-0.012) End gap measured
in
cylinder
mm
(in) Oil (rail) 0.20-0.70 (0.008-0.0276) End gap measured
in
cylinder
mm
(in)
Maximum 1.0 (0.039)
Ring groove width
in
piston
mm (in)

Top 1.52-1.54 (0.0598—0.0606)
Ring groove width
in
piston
mm (in)
Second 1.52-1.54 (0.0598-0.0606) Ring groove width
in
piston
mm (in)

Oil 4.02-4.04 (0.1583—0.1591)
Clearance
of
piston ring
to
ring
groove
mm
(in)
Top 0.03-0.07 (0.0012-0.0028) Clearance
of
piston ring
to
ring
groove
mm
(in) Second 0.03-0.07 (0.0012-0.0028) Clearance
of
piston ring
to
ring
groove
mm
(in) Maximum 0.15 (0.006)

Piston pin

Diameter
mm (in)
21.987-21.993 (0.8656-0.8659)
Connecting rod
to
piston pin clearance
mm (in)
0.010-0.027 (0.0004-0.0011)
Piston
to
piston pin clearance
mm
(in) -0.005-0.011 (-0.0002-0.0004)

Connecting rod and connecting rod bearing

Length (Center and center)
mm (in)
149.95—150.05 (5.904-5.907)
Twisting and bending
mm
(in) 0.06 (0.0024) max.
Small end bore
mm (in)
22.003-22.014 (0.8663-0.8667)
Big end bore
mm (in)
54.002-54.017 (2.1261-2.1266)
Big end width
mm
(in) 26.838-26.890 (1.0566-1.0587)
Connecting rod side clearance
mm
(in) Standard 0.110-0.262 (0.004-0.010) Connecting rod side clearance
mm
(in) Maximum 0.30 (0.012)

Crankshaft

Crankshaft runout
mm (in)
Maximum 0.03 (0.0012)
Main journal diameter mm (in)
Standard size 59.937-59.955 (2.3597-2.3604)
Main journal diameter mm (in)
0.25 (0.010)
undersize
Standard 59.693—59.711 (2.3051-2.3508)
Main journal diameter mm (in)
0.25 (0.010)
undersize No.
3
59.687-59.705 (2.3499-2.35061 Main journal diameter mm (in) 0.50 (0.020)
undersize
No. 1,2,4,5 59.443-59.461 (2.3403-2.3410) Main journal diameter mm (in) 0.50 (0.020)
undersize No.
3
59.437-59.455 (2.3400-2.3407)
Main journal diameter mm (in)
0.75 (0.030)
undersize
No. 1,2,4,5 59.193-59.211 (2.3304-2.3311)
Main journal diameter mm (in)
0.75 (0.030)
undersize No.
3
59.187-59.205 (2.3302-2.3309)
Main journal taper and out-of-round mm (in) Maximum 0.05 (0.0020)
Crankpin diameter
mm
(in)
Standard 50.940-50.955 (2.0055-2.0061)
Crankpin diameter
mm
(in) 0.25 (0.010) undersize 50.690-50.705 (1.9957-1.9963) Crankpin diameter
mm
(in) 0.50 (0.020) undersize 50.440-50.455 (1.9858-1.9864) Crankpin diameter
mm
(in)
0.75 (0.030) undersize 50.190-50.205 (1.9760-1.9766)
Crankpin taper and out-of-round
mm
(in) Maximum 0.05 (0.0020)

Main bearing

Main journal bearing
oil
clearance
mm
(in)
No. 1,2,4,5 Standard 0.025-0.043 (0.0010-0.0017)
Main journal bearing
oil
clearance
mm
(in)
No. 1,2,4,5 Maximum 0.08 (0.0031) Main journal bearing
oil
clearance
mm
(in) No.
3
Standard 0.031-0.049 (0.0012-0.0019)
Main journal bearing
oil
clearance
mm
(in) No.
3
Maximum 0.08 (0.0031)
Available undersize bearing
mm
(in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)

Crankpin bearing

Crankpin bearing
oil
clearance
mm
(in) Standard 0.027-0.067 (0.0011-0.0026) Crankpin bearing
oil
clearance
mm
(in) Maximum 0.10 (0.0039)
Available undersize bearina
mm
(in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)

Thrust bearing (center main bearing)

Crankshaft end play
mm
(in) Standard 0.08-0.18 (0.0031-0.0071) Crankshaft end play
mm
(in) Maximum 0.30 (0.0118)
Bearing width
mm
(in)
Standard 27.94-27.99 (1.100-1.102)
Bearing width
mm
(in) 0.25 (0.010) oversize 28.04—28.09 (1.104-1.106) Bearing width
mm
(in) 0.50 (0.020) oversize 28.12—28.17 (1.107-1.109) Bearing width
mm
(in)
0.75 (0.030) oversize 28.20-28.25 (1.110-1.112)

Timing belt

Belt deflection
mm
(in)/98
N
(10 kg,
22 lb)
7.5-8.5 (0.30-0.33)

30—10

TECHNICAL DATA 30
1C. ENGINE (DIESEL)
— _____ Engine model Item . RF-CX RF-N

Type Diesel, 4-cycle
Cylinder arrangement and number In-line, 4-cylinders
Type
of
combustion chamber Swirl chamber
Valve system OHC, belt-driven
Bore
x
Stroke
mm (in)
86.0
x
86.0 (3.39
x
3.39)
Total piston displacement
cc
(cu
in)
1,998 (121.9)
Compression ratio 21.1
: 1 |
22.7
: 1

Compression pressure
kPa (kg/cm2, psi)-rpm
Standard 2,943 (30, 427)-200
Compression pressure
kPa (kg/cm2, psi)-rpm Minimum 2,649 (27, 384)-200 Compression pressure
kPa (kg/cm2, psi)-rpm Maximum difference
between cylinders 294 (3.0,
43)

Valve timing
IN Open BTDC 13° 13°
Valve timing
IN Close ABDC 15° 39° Valve timing
EX Open BBDC 60° 60° Valve timing
EX Close ATDC 8° 8°
Valve clearance
mm
(in) IN Cold: 0.25 (0.010), Warm: 0.30 (0.012) Valve clearance
mm
(in) EX Cold: 0.35 (0.014), Warm: 0.40 (0.016)

Cylinder head

Height mm (in) 133.9-134.1 (5.272-5.280)
Distortion mm (in) 0.10 (0.004) max.
Length
of
cylinder head bolt beiow head
mm
(in)
Standard 113.2—113.8 (4.457—4.480) Length
of
cylinder head bolt beiow head
mm
(in) Maximum 114.5 (4.508)

Combustion chamber insert

Recession
mm
(in) 0.020 (0.0008)
Projection
mm
(in) 0.005 (0.0001)

Valve and valve guide

Valve head diameter
mm
(in) IN 39.3-39.5 (1.547—1.555) 40.9-41.1 (1.610—1.618) Valve head diameter
mm
(in) EX 35.0-35.2 (1.378-1.386) 35.9-36.1 (1.413—1.421)
Valve head thickness (margin)
mm
(in) IN 1.80 (0.071) 0.80 (0.031) Valve head thickness (margin)
mm
(in) EX 1.65 (0.065) 0.80 (0.031)
Valve face angle IN 60° 45° Valve face angle EX 45°
Valve length mm (in) IN 106.9(4.209) Valve length mm (in) EX 106.8 (4.205)
Valve stem diameter
mm
(in) IN 7.970-7.985 (0.3138—0.3144) Valve stem diameter
mm
(in) EX 7.965-7.980 (0.3136-0.3142)
Guide inner diameter mm (in) IN 8.025-8.045 (0.3159—0.3167) Guide inner diameter mm (in) EX 8.025-8.045 (0.3159—0.3167)
Valve stem
to
guide clearance
mm (in)

IN 0.040-0.075 (0.0016-0.0030)
Valve stem
to
guide clearance
mm (in)
EX 0.045—0.080 (0.0018-0.0031) Valve stem
to
guide clearance
mm (in)

Maximum 0.1 (0.004)
Guide projection (Height "A")
mm
(in) 8.3-8.8 (0.327-0.346)

Valve seat

Seat angle IN 60° 45° Seat angle EX 45°
Seat contact width
mm
(in) IN 1.4-1.8 (0.055—0.071) 1.7-2.3 (0.067-0.091) Seat contact width
mm
(in) EX 1.64-2.04 (0.065-0.080) 1.7-2.3 (0.067-0.091)
Seat sinking (Measure valve recession)
mm
(in)
IN Standard 0.75-1.05 (0.030-0.041)
Seat sinking (Measure valve recession)
mm
(in)
IN Maximum 2.55 (0.100) Seat sinking (Measure valve recession)
mm
(in) EX Standard 0.75—1.05 (0.030-0.041) Seat sinking (Measure valve recession)
mm
(in) EX Maximum 2.55 (0.100)

Valve spring

Free length
mm
(in) Standard 45.11 (1.776) Free length
mm
(in) Minimum 44.8 (1.764)

30-11

TECHNICAL DATA 30
Item Engine model RF-CX RF-N
Connecting rod and connecting rod bearing

Length (Center
to
center) mm (in) 151.95-152.05 (5.9823—5.9862)
Maximum twisting and bending mm (in) 0.080 (0.0031)
per 50
(1.969)
Small end bushing inner diameter mm (in) 30.014-30.030 (1.1817-1.1823) 25.014-25.030 (0.9848-0.9854)
Big end bore mm (in) 54.002-54.017 (2.1261-2.1266)
Big end width mm (in) 25.900—26.100 (1.0197—1.0276)
Connecting rod side clearance mm (in) Standard 0.11-0.262 (0.0043-0.0103) Connecting rod side clearance mm (in) Maximum 0.30 (0.012)

Crankshaft

Crankshaft runout mm (in) 0.05 (0.002) max.
Standard Standard 59.937-59.955 (2.3597-2.3604)
size Minimum 59.89 (2.358)
0.25 (0.010) Standard 59.687-59.705 (2.3499-2.3506)
Main journal diameter undersize Minimum 59.64 (2.348) mm (in) 0.50 (0.020) Standard 59.437-59.455 (2.3400-2.3407)
undersize Minimum 59.39 (2.338)
0.75 (0.030) Standard 59.187-59.205 (2.3302-2.3309)
undersize Minimum 59.14 (2.328)
Main journal taper and out-of-round mm (in) 0.05 (0.002) max.
Standard Standard 50.940-50.955 (2.0055—2.0061)
size Minimum 50.89 (2.004)
0.25 (0.010) Standard 50.690-50.705 (1.9957-1.9963)
Crankpin diameter undersize Minimum 50.64 (1.994) mm (in) 0.50 (0.020) Standard 50.440-50.455 (1.9858—1.9864)
undersize Minimum 50.39 (1.984)
0.75 (0.030) Standard 50.190-50.205 (1.9760-1.9766)
undersize Minimum 50.14 (1.974)
Crankpin taper and out-of-round mm (in) 0.05 (0.002) max.

Main bearing

Main journal bearing
oil
clearance Standard 0.031-0.050 (0.0012-0.0020)
mm (in) Maximum 0.08 (0.0031)
Available undersize bearina mm fin) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)

Crankpin bearing

Crankpin bearing
oil
clearance mm (in) Standard 0.027-0.055 (0.0011-0.0022) Crankpin bearing
oil
clearance mm (in) Maximum 0.08 (0.0031)
Available undersize bearing mm (in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)

Thrust bearina (center main bearina)

Crankshaft end play mm (in) Standard 0.04-0.282 (0.0016—0.0111) Crankshaft end play mm (in) Maximum 0.30 (0.012)
Bearing width mm (in) Standard size 2.00-2.05 (0.0787-0.0807) Bearing width mm (in) Oversize 2.175-2.225 (0.0856-0.0876)

Timing belt

Deflection mm (in)/N (ka,
lb)
9.0-11.5 (0.35--0.45V98 (10,
22)
Drive belt deflection

Alternator mm (in) New 8-10 (0.31-0.39) Alternator mm (in) Used 9-11 (0.35-0.43)
A/C compressor mm (in) New 8.5-9.5 (0.33-0.37) A/C compressor mm (in) Used 9.5-10.5 (0.37-0.41)
Vacuum pump mm (in) New 7.5-8.5 (0.30—0.33) Vacuum pump mm (in) Used 8.5-9.5 (0.33-0.37)
P/S pump with vacuum pump mm (in) New 6.5-7.5 (0.26—0.30) P/S pump with vacuum pump mm (in) Used 7.0-8.0 (0.28—0.31)
Pressure wave supercharger
mm
(in) New 4.0-5.0 (0.16-0.20) Pressure wave supercharger
mm
(in) Used 4.5-5.5 (0.18-0.22)

30—13