fuel MAZDA 626 1987 Service Manual

1C REMOVAL
76G01C-244
76G01C-072
67U01X-029
Removal Note
Fuel hose
Warning
a) Cover the hose with a rag because fuel will
spray out when disconnecting.
b) Keep fire and open flame away from the fuel
area.
After disconnecting the fuel hoses, plug them to avoid
fuel leakage.
Clutch release cylinder
Remove the clutch release cylinder with the pipe still
connected; then avoid the cylinder.
P/S pump, A/C compressor
Remove the P/S pump and A/C compressor with the
hoses still connected to them, secure the pump and
compressor as shown in the figure.
Driveshaft
Remove the driveshafts. (Refer to Section 9.) Slide
the SST into the transaxle.
86U01X-060
1C-32

DISASSEMBLY (INJECTION PUMP) 1 C
INJECTION PUMP
76G01C-082
1. No.3 engine mount and idler
2. Injection pipe
3. Injection pump
4. Oil level gauge and stay
5. Oil pipe
6. Fuel feed pipe
7. Oil pressure switch
8. Water pipe
9. Water pump
Disassembly Note
Injection pump
Remove the injection pump with its brackets.
If separate them, adjust the injection timing after in-
stalling the timing belt referring to Section 4D.
76G01C-083
1C-39

1 C DISASSEMBLY (CYLINDER HEAD)
CYLINDER HEAD
76G01C-079
1. Thermostat cover
2. Thermostat
3. Thermostat case
4. Front and rear engine
hanger
5. Fuel leak pipe
6. Injection nozzle
7. Glow cord
8. Glow plug
9. Camshaft cap
10. Oil seal
11. Camshaft
12. Cylinder head bolt
13. Cylinder head and gasket
14. Tappet and adjusting disc
15. Valve keepers
16. Upper spring seat
17. Valve spring
18. Valve
19. Lower spring seat
20. Valve seal
21. Valve guide and clip
1C-40

ASSEMBLY (INJECTION PUMP) 1 C
Water Pipe
1. Apply a coat of vegetable oil to the O-ring.
2. Install the water pipe.
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
3. Connect the water hose.
76G01C-181
^OQOja^q^
cffl-.. M
Oil Pressure Switch
Install the oil pressure switch.
Tightening torque: 12—18 N-m
(1.2—1.8 m-kg, 104—156 in-lb)
76G01C-182
Fuel Feed Pipe and Oil Pipe
1. Install the fuel feed pipe and tighten bolt (A).
Tightening torque:
19—26 N-m (1.9—2.6 m-kg, 14—19 ft-lb)
2. Install the oil pipe and loosely tighten the bolts (B).
76G01C-183
"m
fa?-^ lA-f! . 11
? - ' ~" ~ -'
Oil Level Gauge
Install the oil level gauge and stay.
Tightening torque:
8—12 N-m (80—120 cm-kg, 69—104 in-lb)
76G01C-184
1C-79

1 C ASSEMBLY (INJECTION PUMP)
Injection Pump
1. Install the injection pump with the injection pump
brakcet.
Tightening torque:
37—52
N m
(3.8—5.3 m-kg, 27—38 ft-lb)
Note
If the injection pump bracket and the injection
pump are separated, injection timing adjust-
ment is necessary after installing the timing
belt.
2. Connect the CSD water hose and fuel hoses.
Injection Pipe
1. Check that no dirt or other foreign material is on
the pipe coupling.
2. Install the fuel injection pipes.
Tightening torque:
25—29 Nm (2.5—3.0 m-kg, 18—22 ft-lb)
76G01C-186
m.«JL
Qja .

^ }
No.3 Engine Mount and Idler
Install the No.3 engine mount and idler.
Tightening torque:
37—52
N
m (3.8—5.3 m-kg, 27—38 ft-lb)
76G01C-187
1C—80

INSTALLATION 1C
Heater Hose
Connect the heater hoses.
Note
Position the hose clamp in the original loca-
tion on the hose and squeeze the clamp lightly
with large pliers to ensure a good fit.
86U01X-221
Connector Location
Install each harness as shown in the figure.
1. Alternator
2. Boost air temperature sensor (RF-CX)
3. Heat gauge unit
4. Water thermo switch
5. Pick up coil
6. Glow cord
7. Front harness connector and ground
76G01C-222
8. Fuel cut valve
9. Oil pressure switch
10. Starter
11. Water temperature switch
12. Transaxle harness
13. Grounds
1C—95

INSTALLATION 1C
76G01C-227
P/S Oil Pump
1. Install the P/S oil pump.
Tightening torque:
37—52 Nm (3.8—5.3 m-kg, 27—38 ft-lb)
2. Install the P/S oil pump pully. (Refer to section 10)
Tightening torque:
55—59 Nm (5.6—6.0 m-kg, 41—43 ft-lb)
3. Set the pipe bracket in position.
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
4. Install the drive belt and adjust the belt deflection.
(Refer to page 1C—7)
5. Install the drive belt cover.
Tightening torque:
8—11
N
m (80—110 cm-kg, 69—95 in-lb)
76G01C-228
Fuel Hose
Install the fuel hose.
Note
Be careful of the red marks on the hose.
76G01C-229
76G01C-230
Intercooler Pipe and Hose
1. Install the intercooler pipe and hose.
Tightening torque:
19—26 Nm (1.9—2.6 m-kg, 14—19 ft-lb)
2. Install the brake vacuum pipe.
Tightening torque:
8—11
N
m (80—110 cm-kg, 69—95 in-lb)
3. Connect the brake vacuum hose securely and
squeeze the clamp lightly with pliers to ensure a
good fit.
1C-97

4A
FUEL AND EMISSION
CONTROL SYSTEMS
(CARBURETOR)
OUTLINE 4A— 2
SYSTEM DIAGRAM 4A— 2
VACUUM HOSE ROUTING
DIAGRAM 4A— 5
EMISSION COMPONENTS
LOCATION 4A— 8
COMPONENT DESCRIPTIONS 4A—12
SPECIFICATIONS 4A—15
TROUBLESHOOTING GUIDE 4A—17
PARTS INSPECTION 4A—23
AIR CLEANER ELEMENT 4A—23
ACCELERATOR LINKAGE 4A—23
INTAKE MANIFOLD 4A—23
CHOKE CABLE 4A—23
FUEL SYSTEM 4A—24
TROUBLESHOOTING 4A—25
CARBURETOR 4A—26
FUEL PUMP 4A—35
FUEL TANK 4A—36
SEPARATOR 4A—37
TWO-WAY CHECK VALVE 4A—37
THREE-WAY CHECK VALVE 4A—37
FUEL FILTER 4A—37
IDLE SPEED AND IDLE MIXTURE.. 4A—38
ADJUSTMENT 4A—38
AUTO-RETURN CHOKE SYSTEM... 4A—40
TROUBLESHOOTING 4A—40
PTC HEATER SYSTEM 4A—42
TROUBLESHOOTING 4A—42
DECELERATION CONTROL SYSTEM 4A—45
TROUBLESHOOTING 4A—45
BYPASS AIR CONTROL SYSTEM.. 4A—48
DASH POT 4A—50
ANTI-AFTERBURN VALVE 4A—50
MAIN AIR BLEED CONTROL
SYSTEM 4A—51
SLOW FUEL CUT SYSTEM 4A—53
COAST ENRICHMENT SYSTEM .... 4A—54
COASTING LEANER SYSTEM 4A—56
AIR INJECTION SYSTEM 4A—58
INTAKE AIR TEMPERATURE CONTROL
SYSTEM 4A—60
TROUBLESHOOTING 4A—60
PURGE CONTROL SYSTEM 4A—63
VACUUM SWITCH VALVE 4A—63
EXHAUST GAS RECIRCULATION
(EGR) SYSTEM 4A—64
TROUBLESHOOTING 4A—65
POSITIVE CRANKCASE VENTILATION
SYSTEM 4A—67
PCV VALVE 4A—67
IDLE-UP CONTROL SYSTEM 4A—68
TROUBLESHOOTING 4A—70
IDLE-UP SOLENOID VALVE 4A—76
EVAPORATIVE EMISSION CONTROL
SYSTEM 4A—78
TROUBLESHOOTING 4A—79
IGNITION TIMING CONTROL
SYSTEM 4A-80
TROUBLESHOOTING 4A—81
CONTROL SYSTEM 4A-83
RELATIONSHIP CHART 4A—84
ENGINE CONTROL UNIT 4A—86
INHIBITOR SWITCH 4A—93
IDLE SWITCH 4A—93
VACUUM SWITCH 4A—94
WATER THERMO SWITCH 4A—95
EXHAUST SYSTEM 4A—96
76G04A-001

Diaphragm

Intake air temperature
Water thermo switches*2 Vacuum switch*2 E/L switches*2 Inhibitor switch*2 Ignition coil
Fuel pump
Water thermo
switch*2
(on radiator)
*1 MTX
*2 Except F6
*3 F6
*4 Except F8 ATX and F6
*5 F6 MTX
*6 Except F8 ATX and F6 ATX
*7 F8 MTX and FE

Engine
control
unit
Engine
control
unit
Ignition coil
Slow fuel cut solenoid
valve ^Reed valve
ATX1
1
MTY