fuel MAZDA 626 1987 Manual Online

PTC HEATER SYSTEM 4A
System Inspection
Except FE 8Valve—Unleaded Fuel
1. Connect a voltmeter to the PTC heater connector.
2. Start the engine and measure the voltage.
Specification
Radiator coolant
temperature Below 17°C (63°F) Above
17°C (63°F)
Voltage Approx. 12V ov
76G04A-073
FE 8Valve—Unleaded Fuel
1. Start the engine.
2. Connect a voltmeter to the PTC heater connector
terminals and measure the voltage.
Voltage
Engine coolant
temperature
Below 67°C (152°F)
Above 67°C (152°F)
Radiator coolant temperature Below 17°C (63°F) Above 17°C (63°F) —
Terminal BrB Approx.
12V
OV OV Terminal BrW
Approx.
12V Approx. 12V OV
76G04A-074
PTC Heater
Except FE 8Valve—Unleaded Fuel
1. Disconnect the PTC heater connector.
2. Check for continuity of the heater with an
ohmmeter.
76G04A-075
FE 8Valve—Unleaded Fuel
1. Disconnect the PTC heater connector.
2. Check for continuity between terminal wire (BrW)
and a ground.
3. Check for continuity between terminal wire (BrB)
and (B).
76G04A-076
4A—43

4 A DECELERATION CONTROL SYSTEM
TROUBLESHOOTING
Check the condition of the wiring harness and connectors before checking the engine control unit
or switches.
FE 12Valve and F8 (ECE, Hong Kong and Singapore)—MTX
Possible cause
Page
Symptom

Anti-afterburn

valve
Dashpot Bypass
air
control
system
Idle

switch
main
air

bleed

control
system

Engine

control

unit

terminal
Possible cause
Page
Symptom

Anti-afterburn

valve
Dashpot Bypass
air
control
system
Idle

switch
main
air

bleed

control
system
E L M
Possible cause
Page
Symptom 4A—50 4A—50 4A—48 4A—93 4A—51 4A—88
Runs rough on deceleration 2 1 3 5 4
Afterburn in exhaust system 1 2 4 3 5 6
Poor fuel consumption 1 2 3
Fails emission test 7 6 1 2 3 4 5
High idle speed after warm up 1 2 3
Engine stalls during warm up 1
Rough idle during warm up 1
Poor acceleration, hesitation, or lack of power 1
76G04A-079
FE 12Valve and F8 (ECE, Hong Kong and Singapore)—ATX
Possible cause o> o 4-* uT u. E 3
(0 >
c k_ 3 •Q L-
2 ST c
o o "O at 0)
_>. c O
£ O
o w c o
• 1
\Page a •
C
3 i CO V S.
v>

5 E c ® 5 »
5 w a> in m
< BO M S «T 2 B D 2N
Symptom 4A—50 4A—48 4A—51 4A—93 4A—86
Runs rough on deceleration 2 3 1 5 4
Afterburn in exhaust system 1 2 3 4 5
Poor fuel consumption 1 2
Fails emission test 7 6 2 1 3 4 5
High idle speed after warm up 1 2
Engine stall during warm up 1
Rough idle during warm up 1
Poor acceleration, hesitation, or lack of power 1
76G04A-080
4A—46

DECELERATION CONTROL SYSTEM 4 A
FE 8Valve—Unleaded Fuel
Possible cause
\Page ^s^
Symptom

Slow

fuel
cut
system
Coast
enrichment
system
Idle

switch
Anti-afterburn
valve

Bypass

air
control

system
Dashpot
(only
MTX)
Engine
control
unit

terminal

Possible cause
\Page ^s^
Symptom

Slow

fuel
cut
system
Coast
enrichment
system
Idle

switch
Anti-afterburn
valve

Bypass

air
control

system
Dashpot
(only
MTX)
A C G I
Possible cause
\Page ^s^
Symptom 4A-53 4A-54 4A-93 4A-50 4A-48 4A-50 4A—91
Runs rough on deceleration 8 6 1 7 3 4 5 2
Afterburn in exhaust system 7 3 1 4 2 5 8 6
Poor fuel consumption 2 1 6 5 4 3
High idle speed after warm up 2 1 3
Fails emission test 4 2 1 5 3 6 7 8 9
76G04A-081
FE 8Valve (General)
Possible cause main air bleed control
solenoid valve
Engine control unit terminal
Possible cause main air bleed control
solenoid valve
MTX ATX
Possible cause main air bleed control
solenoid valve
E F B 2F j 21
Page 4A—51 4A—90 4A—89
Checking order 1 2
76G04A-082
F6 (Singapore)
Possible cause
X^Page
Symptom

Dashpot

(Only

MTX)
Anti-afterburn
valve

idle

switch
L
Coasting

leaner

solenoid

valve
Engine

control

unit

terminal

Possible cause
X^Page
Symptom

Dashpot

(Only

MTX)
Anti-afterburn
valve

idle

switch
L
Coasting

leaner

solenoid

valve
B D
Possible cause
X^Page
Symptom 4A—50 4A—50 4A—93 4A—56 4A—92
High idle speed after warm up 1
Runs rough on deceleration 1 2 3
Afterburn In exhaust system 5 4 1 2 3
Fails emission test 4 1 2 3
76G04A-083
4A—47

4 A DECELERATION CONTROL SYSTEM
BYPASS AIR CONTROL SYSTEM
FE and F8 [Except General and Middle East]
E -tr Air bypass solenoid valve
I
Engine
control
unit
FE 8 Valve — Unleaded fuel

J
f^^n
Ignition coil
Idle switch
76G04A-084
The bypass air control system consists of the bypass solenoid valve, idle switch, ignition coil, and en-
gine control unit.
This system opens the bypass air passage to the intake manifold during deceleration above ap'prox.
2,300 rpm (ECE, Hong Kong, and Singapore), or above approx. 3,500 rpm (FE 8 Valve—Unleaded
fuel).
Note
Make the system inspection first. If no problem is found, continue with the next inspec-
tion of the Troubleshooting. (Refer to page 4A—46 or 47.)
Troubleshooting
Possible cause System inspection Air bypass solenoid valve
Page 4A-48 4A-49
Checking order 1 2
/
/o fcl i /o ' jXj^/* J
V\ i \\ I M
p)
/ Terminal AGL...Leaded Fuel
L LB...FE 8 Valve—Unleaded Fuel
System Inspection
1. Warm up the engine and run it at idle.
2. Connect a tachometer.
3. Disconnect the bypass air hose from the air cleaner
and place a finger over the hose opening.
76G04A-085
4A—48

DECELERATION CONTROL SYSTEM 4 A
MAIN AIR BLEED CONTROL SYSTEM
FE and F8 (ECE, Hong Kong, Singapore, and General)
Primary
Air/Fuel mixture—Lean Air/Fuel mixture—Rich
76G04A-093
This system prevents the additional air from being fed to the primary air bleed circuit and causes the
air/fuel mixture to become rich, improving acceleration.
Troubleshooting
Possible cause System inspection Solenoid valve Vacuum switch Water thermo
switch (Radiator)
Page 4A—52 4A—52 4A—94 4A—95
Checking order 1 2 3 4
Note
Make the system inspection first. If no problem is found, continue with the next inspec-
tion of the Troubleshooting. (Refer to pages 4A—46 or —47.)
4A—51

DECELERATION CONTROL SYSTEM 4 A
SLOW FUEL CUT SYSTEM [FE 8VALVE—UNLEADED FUEL]
76G04A-096
This system shuts the primary slow fuel passage to prevent run-on and overheating of the exhaust
system when the ignition switch is turned OFF or during deceleration (engine speed above 2,300
rpm and idle switch ON). The slow fuel cut solenoid is actuated by the engine control unit and ignition
switch.
Troubleshooting
Note
Make the system inspection first. If no problem is found, continue with the next inspec-
tion of the Troubleshooting Guide. (Refer to page 4A—47.)
Possible cause System inspection Slow fuel cut solenoid valve
Page 4A—53 4A—34
Check order 1 2
System Inspection
1. Warm up the engine and run it at idle.
2. Connect a tachometer to the engine.
3. Connect a voltmeter to the carburetor connector
terminal (BW wire).
4. Increase the engine speed to 4,000 rpm; then re-
lease the throttle lever.
5. Measure the terminal voltage.
Engine speed Voltage
Above approx. 2,300 rpm Approx. 12V
Below approx. 2,300 rpm Below 1.5V
76G04A-097
4A-53

4 A DECELERATION CONTROL SYSTEM
COAST ENRICHMENT SYSTEM [FE 8VALVE—UNLEADED FUEL]
Ignition coil
Engine
control
unit
Coast enrichment
solenoid valve
Richer air bleeds
Secondary main
air bleed
Idle switch
© e
To secondary
main jet
76G04A-098
This system opens the fuel passage to the secondary stage of the carburetor during deceleration at
engine speeds of 2,300—1,500 rpm. The coast enrichment solenoid valve is actuated by the engine
control unit.
Troubleshooting
Possible cause System Inspection Coast enrichment solenoid valve
Engine control unit terminal Possible cause System Inspection Coast enrichment solenoid valve
A B D 1
Page 4A—54 4A—55 4A—91
Checking order 1 3 2
System Inspection
1. Warm up the engine to the normal operating tem-
perature and run it at idle.
2. Connect a voltmeter to the carburetor connector
terminal E.
3. Connect a tachometer to the engine.
76G04A-099
4A—54

4 A INTAKE AIR TEMPERATURE CONTROL SYSTEM
INTAKE AIR TEMPERATURE CONTROL SYSTEM
76G04A-112
This system controls air intake temperature to prevent icing and operates depending on air tempera-
ture around the control valve.
TROUBLESHOOTING
Note
Make the system inspection first. If no problem is found, continue with the next inspec-
tion of the Troubleshooting Guide. (Refer to pages from 4A—17 to 4A—22.)
FE and F8 (General, ECE, and Hong Kong) and Singapore
Possible cause
Symptom
System inspection Vacuum control
diaphragm
Intake air temperature control valve
Possible cause
Symptom 4A—61 4A—61 4A—61
Checking order 1 2 3
FE 8 Valve—Unleaded Fuel, Middle East, and F6—General
Possible cause System inspection
Page 4A—62
Checking order 1
76G04A-113
4A-60

4A INTAKE AIR TEMPERATURE CONTROL SYSTEM
System Inspection
Bimetal type
[FE 8Valve—Unleaded Fuel]
Move the control valve inside the air cleaner, and
check that it moves freely and that spring force is felt.
System Inspection
Manual type
[Middle East and F6—General]
Change the summer-winter change lever and check
that it moves smoothly.
76G04A-119
4A—62

PURGE CONTROL SYSTEM 4 A
PURGE CONTROL SYSTEM
[FE 8VALVE—UNLEADED FUEL]
Vaccum switch valve -4
I
Water thermo valve
76G04A-120
This system supplies additional air to the intake manifold to improve the driveability when the engine
coolant temperature is above 50°C (122°F).
TROUBLESHOOTING
Possible cause Vacuum switch valve Water thermo valve
Page 4A—63 4A—66
Checking order 1 2
VACUUM SWITCH VALVE
1. Connect a vacuum pump to the purge control
valve as shown in the figure.
2. Blow through the valve from port A and check that
air does not come out of port B.
3. Apply 100 mm-Hg (3.94 InHg) vacuum.
4. Blow through port A and check that air comes out
of port B.
5. Replace if necessary.
76G04A-121
4A-63