coolant MAZDA 626 1987 Repair Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 1987, Model line: 626, Model: MAZDA 626 1987Pages: 1865, PDF Size: 94.35 MB
Page 417 of 1865

4 A DECELERATION CONTROL SYSTEM
Solenoid valve (for main air bleed control system)
76G04A-094
76G04A-095
76G04A-191
System Inspection
1. Disconnect the vacuum switch connector.
2. Make sure that radiator coolant temperature is be-
low 17°C (63°F).
3. Disconnect the upper vacuum hose from the sole-
noid valve.
4. Place a finger over the solenoid valve open port
and check that vacuum is not felt when engine is
running.
5. Warming up the engine.
6. Place a finger over the same open port of the sole-
noid valve and check that weak vacuum is felt.
7. Reconnect the vacuum switch connector.
8. Check that weak vacuum is felt at the open port
of the solenoid valve at idle.
9. Accelerate the engine rapidly and check that vacu-
um is not felt.
Solenoid Valve (A/C)
1. Disconnect vacuum hose A (White) from the car-
buretor.
2. Disconnect vacuum hose B from the solenoid
valve.
3. Disconnect the solenoid valve connector.
4. Blow air through the valve from hose A and check
that it comes out of port C.
5. Apply 12V and ground to the solenoid valve with
jumper wires.
6. Blow air through the valve from hose A and check
that air not come out.
7. Replace if necessary.
76G04A-192
4A—52
Page 428 of 1865
![MAZDA 626 1987 Repair Manual
PURGE CONTROL SYSTEM 4 A
PURGE CONTROL SYSTEM
[FE 8VALVE—UNLEADED FUEL]
Vaccum switch valve -4
I
Water thermo valve
76G04A-120
This system supplies additional air to the intake manifold to i MAZDA 626 1987 Repair Manual
PURGE CONTROL SYSTEM 4 A
PURGE CONTROL SYSTEM
[FE 8VALVE—UNLEADED FUEL]
Vaccum switch valve -4
I
Water thermo valve
76G04A-120
This system supplies additional air to the intake manifold to i](/img/28/57059/w960_57059-427.png)
PURGE CONTROL SYSTEM 4 A
PURGE CONTROL SYSTEM
[FE 8VALVE—UNLEADED FUEL]
Vaccum switch valve -4
I
Water thermo valve
76G04A-120
This system supplies additional air to the intake manifold to improve the driveability when the engine
coolant temperature is above 50°C (122°F).
TROUBLESHOOTING
Possible cause Vacuum switch valve Water thermo valve
Page 4A—63 4A—66
Checking order 1 2
VACUUM SWITCH VALVE
1. Connect a vacuum pump to the purge control
valve as shown in the figure.
2. Blow through the valve from port A and check that
air does not come out of port B.
3. Apply 100 mm-Hg (3.94 InHg) vacuum.
4. Blow through port A and check that air comes out
of port B.
5. Replace if necessary.
76G04A-121
4A-63
Page 441 of 1865

4A IDLE-UP CONTROL SYSTEM
IDLE-UP SOLENOID VALVE
FE and F8 (General, ECE, Hong Kong, and Singapore)
Water thermo switch Fan speed control switch Headlights _
Rear defroster
A/C
Engine1
control -
unit
Richer air bleed
Richer jet
/ '
Inhibitor switch
Water thermo switch Fan speed _ control switch Headlights -
Rear defroster —
A/C
Engine
control
unit
Idle-up solenoid valve
Adjust screw
Secondary
throttle valve
From secondary main jet
76G04A-151
The idle-up solenoid valve opens when the following conditions are met.
Condition
When inhibitor switch is OFF (ATX—other than "P" and "N" range) and any of the following:
• Engine coolant temperature less than 72°C (162°F).
• A/C operated.
• Fan speed control switch 3rd or 4th position.
• Headlights turned on.
• Rear defroster turned on.
4A—76
Page 445 of 1865

4 A IGNITION TIMING CONTROL SYSTEM
IGNITION TIMING CONTROL SYSTEM
F8 and FE (12-VALVE)—ATX (ECE, Singapore, and Hong Kong)
Ignition coil
76G04A-160
This system consists of the distributor, solenoid valve, and several switches, vacuum to the vacuum
control unit of the distributor is cut when the conditions below are met.
Item Condition
Engine speed Below 2,300 rpm
Selector lever position Other than P and N range
Coolant temperature Engine coolant: below 72°C (162°F) Radiator coolant: above 17°C (65°F)
4A—80
Page 451 of 1865

4A CONTROL SYSTEM
ENGINE CONTROL UNIT
Check the engine control unit terminal voltages with
a voltmeter.
Caution
a) Warm up the engine before checking the
control unit.
b) If the proper voltage is not obtained, check
the wiring, connections and finally, check
the component.
FE and F8 Engine — ATX (ECE, Hong Kong, and Singapore)
Terminal
(Wire color) Connected to Condition Voltage
1A
(BW)
Ignition switch Ignition switch ON. Battery voltage
m
ST
'-O
Solenoid valve (Main
air
bleed control) Others Battery voltage
m
ST
'-O
Solenoid valve (Main
air
bleed control) Radiator coolant temperature below 17°C (63°F)
or
intake manifold vacuum more than 200 mmHg (7.9 inHg)
Below 1,5V
1C (GO) Solenoid valve (Choke opener) Radiator coolant temperature below 17°C (63°F)
or
during cranking and
27
sec. after engine starts Below 1,5V
Others Battery voltage
1D
(GL)
Air bypass solenoid valve Idle switch OFF and engine speed above approx. 2,100 rpm Below 1,5V
Others Battery voltage
1E
— — —
1F
(G) Solenoid valve (Ignition timing control system)
Radiator coolant temperature above 17°C (63°F),
en-
gine coolant temperature below 72°C (162°F), inhibi-tor switch OFF and engine speed below 2,300
rpm
Below 1.5 V
Others Battery voltage
1G
— — —
1H
(LW) Solenoid valve (A/C) A/C switch
ON
and engine speed below approx. 2,300
rpm
Below 1,5V
Others Battery voltage
11
(YW) Idle-up solenoid valve Inhibitor switch OFF and, headlight switch ON, rear
defroster switch ON, fan speed control switch
is 3rd
or 4th position, A/C operated,
or
engine coolant tem-
perature below 72°C (162°F)
Below 1,5V
Others Battery voltage
1J
(B)
Ground
—
Below 1,5V
9 MSSirSl
ivj
A 1
k *
76G04A-169
4A—86
Page 452 of 1865

CONTROL SYSTEM 4 A
Terminal
(Wire color) Connected to Condition Voltage
2A
(YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
2B (LB) Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1.5 V 2B (LB) Fan speed control switch
Fan speed control switch OFF Battery voltage
2C
(BL)
Rear defroster switch Rear defroster switch
ON
Below 1,5V 2C
(BL)
Rear defroster switch
Rear defroster switch OFF Battery voltage
2D
(LG)
A/C switch A/C operated Below 1,5V 2D
(LG)
A/C switch
A/C not operated Battery voltage
2E
(RG)
Headlight switch Headlight switch OFF Below 1.5 V 2E
(RG)
Headlight switch
Headlight switch
ON
Battery voltage
2F
(GW)
Water thermo switch
(Radiator)
Radiator coolant temperature below 17°C (63°F) Below 1.5V 2F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
2G
-— —
2H
(L)
Water thermo switch (In-
take manifold)
Engine coolant temperature below 72°C (162°F) Below 1,5V 2H
(L)
Water thermo switch (In-
take manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
21
(LY)
Vacuum switch Vacuum less than 200 mmHg (7.9 inHg) Below 1.5V 21
(LY)
Vacuum switch
Vacuum more than 200 mmHg (7.9 inHg) Battery voltage
2J (RL) OD release solenoid valve Engine coolant temperature below 72°C (162°F) Below 1.5V 2J (RL) OD release solenoid valve
Engine coolant temperature above 72°C (162°F) Battery voltage
2K
(-)
— — -
2L (BR)
Inhibitor switch "N"
or "P"
range Below 1.5V 2L (BR)
Inhibitor switch
Others Battery voltage
2M (BY) Ignition switch
(START position)
Ignition switch
ON
Below 1,5V 2M (BY) Ignition switch
(START position) Cranking Battery voltage
2N
(LsB) Idle switch Idling Battery voltage 2N
(LsB) Idle switch
Accelerator pedal depressed Below 1,5V
76G04A-170
{ 2M 2K 21
X
2F 2C
2A
2N 2L 2J 2H 2F 2D 2B
(11 X X
1C 1 A^j
1J 1H 1F 1D 1B
FE and F8 Engine — MTX (ECE, Hong Kong, and Singapore)
Terminal (Wire color) Connected to Condition Voltage
A
(RG) Headlight switch Headlight switch
ON
Below 1,5V A
(RG) Headlight switch
Headlight switch OFF Battery voltage
B
(B)
Ground
—
Below 1,5V
4A-87
Page 453 of 1865

4A CONTROL SYSTEM
Terminal (Wire color) Connected to Condition Voltage
C (BL) Rear defroster switch Rear defroster switch
ON
Below 1,5V C (BL) Rear defroster switch
Rear defroster switch OFF Battery voltage
D
(LG) A/C switch A/C operated Below 1,5V D
(LG) A/C switch
A/C not operated Battery voltage
E (LY) Solenoid valve (Main
air
bleed control) Intake manifold vacuum more than 300 mmHg (11.8 inHg), and radiator coolant temperature above 17°C (63 °F)
Battery voltage E (LY) Solenoid valve (Main
air
bleed control)
Others Below 1,5V
F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature below 17°C (63°F) Below 1,5V F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
G (YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature below 72°C (162°F) Below 1,5V H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
J (BW) Ignition switch Ignition switch
ON
Battery voltage
K (GO) Solenoid valve (Choke opener) Radiator temperature below 17°C (63°F)
or
during cranking and
27
sec. after engine starts Below 1,5V K (GO) Solenoid valve (Choke opener)
Others Battery voltage
L (LsB) Idle switch Idling Battery voltage L (LsB) Idle switch
Accelerator pedal depressed Below 1,5V
M
(GL)
Air bypass solenoid valve Idle switch OFF and engine speed above approx. 2,100 rpm Below 1,5V M
(GL)
Air bypass solenoid valve
Others Battery voltage
0
(BY)
Ignition switch
(START position)
Ignition switch
ON
Below 1,5V 0
(BY)
Ignition switch
(START position) Cranking Battery voltage
P
(LW) Solenoid valve (A/C) A/C switch
ON
and engine speed below approx.
2,300
rpm
Below 1,5V P
(LW) Solenoid valve (A/C)
Others Battery voltage
Q (YW) Idle-up solenoid valve Headlight switch ON, rear defroster switch ON,
fan
speed control switch
is
3rd
or
4th position, A/C oper-ated,
or
engine coolant temperature below 72°C (162°F)
Below 1,5V Q (YW) Idle-up solenoid valve
Others Battery voltage
R
(LB)
Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1,5V R
(LB)
Fan speed control switch
Fan speed control switch OFF Battery voltage
76G04A-171
f ° O M K I G E C
R P N L J H F D B
4A-88
Page 454 of 1865

CONTROL SYSTEM 4 A
FE and F8 Engine — ATX (General)
Terminal (Wire color) Connected to Condition Voltage
1A
(BW)
Ignition switch Ignition switch
ON
Battery voltage
1B (GR) Solenoid valve (Main
air
bleed control) Others Battery voltage 1B (GR) Solenoid valve (Main
air
bleed control) Radiator coolant temperature below 17°C (63°F)
or
intake manifold vacuum more than 200 mmHg (7.9 inHg)
Below 1,5V
1C
— — —
1D
— — —
1E
— — —
1F
— --
1G
-—
1H
(LW) Solenoid valve (A/C) A/C operated Below 1,5V 1H
(LW) Solenoid valve (A/C)
Others Battery voltage
11
(LW) Idle-up solenoid valve Inhibitor switch OFF and, headlight switch ON, rear defroster switch ON, fan speed control switch
is 3rd
or 4th position, A/C operated,
or
engine coolant tem-perature below 72°C (162°F)
Below 1,5V 11
(LW) Idle-up solenoid valve
Others Battery voltage
1J
(B)
Ground
—
Below 1.5V
2A (YL) Ignition coil Ignition switch
ON or
engine running Battery voltage
2B (LB) Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1.5V 2B (LB) Fan speed control switch
Fan speed control switch OFF Battery voltage
2C
(BL)
Rear defroster switch Rear defroster switch
ON
Below 1,5V 2C
(BL)
Rear defroster switch
Rear defroster switch OFF Battery voltage
2D
(LG) A/C switch A/C operated Below 1,5V 2D
(LG) A/C switch
A/C not operated Battery voltage
2E
(RG)
Headlight switch Headlight switch
ON
Below 1,5V 2E
(RG)
Headlight switch
Headlight switch OFF Battery voltage
2F
(GW)
Water thermo switch
(Radiator)
Radiator coolant temperature below 17°C (63°F) Below 1.5V 2F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
2G
— — —
2H
(L)
Water thermo switch
(Intake manifold) Engine coolant temperature below 72°C (162°F) Below 1,5V 2H
(L)
Water thermo switch
(Intake manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
21 (LB)
Vacuum switch Vacuum less than 200 mmHg (7.9 inHg) Below 1.5V 21 (LB)
Vacuum switch
Vacuum more than 200 mmHg (7.9 inHg) Battery voltage
2J
(RL)
OD release solenoid Engine coolant temperature below 72°C (162°F) Below 1,5V 2J
(RL)
OD release solenoid
Engine coolant temperature above 72°C (162°F) Battery voltage
4A-89
Page 455 of 1865

4A CONTROL SYSTEM
Terminal
(Wire color) Connected to Condition Voltage
2K
— — —
2L
(BR) Inhibitor switch "P"
or "N"
range Below 1,5V 2L
(BR) Inhibitor switch
Others Battery voltage
2M
(BY)
Ignition switch
(START position)
Ignition switch
ON
Below 1,5V 2M
(BY)
Ignition switch
(START position) Cranking Battery voltage
2N
— — —
76G04A-172
(2M X
2
X
2F 2C
X 2L
2J 2H 2F 2D 2B
fll X >< X
1J 1H
>< X
1B
FE and F8 Engine — MTX (General)
Terminal (Wire color) Connected to Condition Voltage
A
(W)
Headlight switch Headlight switch
ON
Below 1,5V A
(W)
Headlight switch
Headlight switch OFF Battery voltage
B
(B)
Ground
—
Below 1,5V
C
(BL) Rear defroster switch Rear defroster switch
ON
Below 1,5V C
(BL) Rear defroster switch
Rear defroster switch OFF Battery voltage
D
(LG) A/C switch A/C operated Below 1.5V D
(LG) A/C switch
A/C not operated Battery voltage
E
(LB) Solenoid valve (Main
air
bleed control)
Intake manifold vacuum more than 300 mmHg (11.8 inHg), and radiator coolant temperature above 17°C (63 °F)
Battery voltage E
(LB) Solenoid valve (Main
air
bleed control)
Others Below 1.5V
F
(GW)
Water thermo switch
(Radiator)
Radiator coolant temperature below 17°C (63°F) Below 1,5V F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
G (YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature below 72°C (162°F) Below 1,5V H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
I
— — —
J
(BW)
Ignition switch Ignition switch
ON
Battery voltage
K
— —
L
— — —
M
— — —
N
— —
4A-90
Page 456 of 1865

CONTROL SYSTEM 4 A
Terminal (Wire color) Connected to Condition Voltage
0 (BY)
Ignition switch*
(START position) Ignition switch
ON
Below 1.5V 0 (BY)
Ignition switch*
(START position) Cranking Battery voltage
P
(LW) Solenoid valve (A/C) A/C switch
ON
and engine speed below approx.
2,300
rpm
Below 1,5V
Others Battery voltage
Q (YW) Idle-up solenoid valve Headlight switch ON, rear defroster switch ON,
fan
speed control switch
is
3rd
or
4th position, A/C oper-ated,
or
engine coolant temperature below 72°C (162°F)
Below 1,5V
Others Battery voltage
R
(LB)
Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1,5V R
(LB) Fan speed control switch OFF Battery voltage
*
Not
used
76G04A-173
{
Q
0
><
K
X
G E C A
^
R P
R X
J H F D B
FE 8Valve — Unleaded Fuel
Terminal (Wire color) Connected to Condition Voltage
A
(L)
Coast enrichment solenoid valve Engine speed approx. 1,500—2,300 rpm and idle switch
ON
Below 1,5V A
(L)
Coast enrichment solenoid valve
Others Battery voltage
B
(B)
Ground
—
Below 1,5V
C (LB)
Air bypass solenoid valve Engine speed above approx. 3,500 rpm and idle
switch
ON
Below 1,5V C (LB)
Air bypass solenoid valve
Others Battery voltage
D
(YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
E
— — —
F
(BW)
Ignition switch Ignition switch
ON
Battery voltage
G (YW) Slow fuel cut solenoid valve Engine speed above approx. 2,300 rpm and idle
switch
ON
Battery voltage G (YW) Slow fuel cut solenoid valve
Others Below 1.5V
H
(LW) A/C switch A/C operated and engine speed above approx.
1,500 rpm
Battery voltage H
(LW) A/C switch
A/C not operated
or
engine speed below approx.
1,500 rpm
Below 1,5V
4A—91