coolant temperature MAZDA 626 1987 Workshop Manual

0 PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
EXTERIOR
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Glass, exterior bright metal and paint for damage
• Wheel lug nuts
88—118 N m (9—12 m-kg, 65—87 ft-lb)
• Tire pressures (Refer to section 12)
• All weatherstrips for damage or detachment
• Operation of bonnet release and lock
• Operation of fuel lid and trunk lid (Back door) opener
• Door operation and alignment
• Headlight aiming
INSTALL following parts:
• Wheel caps or rings (if equipped)
• Outside rear view mirror(s)
UNDER BONNET—ENGINE OFF
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Fuel, coolant and hydraulic lines, fittings, connections and
components for leaks
• Engine oil level
• Power steering fluid level (if equipped)
• Brake and clutch master cylinder fluid level (if equipped)
• Windshield washer reservoir fluid level
• Radiator coolant level and specific gravity
Protection °C (°F) Specific gravity at 20°C (68°F)
-4 (25) 1.028
-16(3) 1.054
-26 (-15) 1.066 -40 (-40) 1.078
• Tightness of water hose clamps (including heater hoses)
• Tightness of battery terminals
• Manual transaxle oil level
• Drive belt tensions (Refer to section 1)
• Accelerator cable and its linkage for free movement
• Headlight cleaner fluid level (if equipped)
CLEAN spark plugs
INTERIOR
INSTALL the following parts:
• Rubber stopper for inside rear view mirror
• Fuse for accessories
CHECK the operations of the following items:
• Seat controls (sliding and reclining) and head rest
• Door locks including childproof door locks (if equipped)
• Seat belts and warning system
• Ignition switch and steering lock
• Inhibitor switch (ATX only)
• All lights including warning and indicator lights
• Sound warning system
• Headlight cleaner (if equipped)
• Horn, wipers and washers (front and rear, if equipped)
• Radio and antenna (if equipped)
• Cigarette lighter and clock
• Remote control outside rear view mirrors (if equipped)
• Power windows (if equipped)
• Heater, defroster and air conditioner at various mode
selection (if equipped)
• Sunroof (if equipped)
ADJUST antenna trimmer on radio (if equipped)
CHECK the following items:
• Presence of spare fuse
• Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
• Operation and fit of windows
• Pedal height and free play of brake and clutch pedal
Pedal height mm (in) free play mm (in)
Clutch pedal 216.5-221.5 (8.52-8.72) 5-13 (0.2-0.51)
Brake pedal 222-227 (8.74-8.94) 4-7 (0.16-0.28)
• Parking brake
5-7 noches/98 N (10 kg, 22lb)
UNDER BONNET—ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
• Operation of idle-up system for air conditioner or power
steering (if equipped)
• Automatic transaxle fluid level
• Operation of dash pot
• Initial ignition timing
• Idle speed
ON HOIST
CHECK the following items:
• Underside fuel, coolant and hydraulic lines, fittings, con-
nections and components for leaks
• Tires for cuts or bruises
• Steering linkage, suspension, exhaust system and all un-
derside hardware for looseness or damage
REMOVE protective cover from brake discs
ROAD TEST"
CHECK the following items:
• Brake operation
• Clutch operation
• Steering control
• Operation of meters and gauge
• Squeaks, rattles or unusual noise
• Engine general performance (including turbo)
• Emergency locking retractors
• Cruise control system (if equipped)
AFTER ROAD TEST
REMOVE seat and floor mat protective covers
CHECK for necessary owner information materials, tools and
spare tire in vehicle
-76G00X-002
0-2

1 C ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
CYLINDER HEAD
Removal
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-031
1. Accelerator cable
2. Air cleaner
3. Brake vacuum pipe
4. Intercooler pipe and hose*
5. Drive belt cover
6. Vacuum pump drive belt
7. Fuel hose
8. Water temperature switch
connector
9. Glow plug connector
10. Water thermo switch con-
nector
11. Heat gauge unit connector
12. Boost air temperature sen-
sor connector*
13. Injection pipes
14. Upper radiator hose
15. Water hose
(thermostat—FIR)
16. Oil level gauge and stay
bolt
17. Oil pipe bolt
18. Timing belt (Refer to page
1C—11)
19. Cylinder head cover
20. Camshaft pulley
21. Rear camshaft pulley
76G01C-032
22. Injection pump pulley
23. Seal plate
24. Water hose and pipe
25. Comprex supercharger
drive belt*
26. Heat insulator*
27. Exhaust manifold stay
28. Front exhaust pipe
29. Cylinder head bolt
30. Cylinder head
31. Cylinder head gasket
32. Comprex supercharger*
33. Exhaust manifold
34. Intake manifold
Note
* marked parts are equipped only for the RF-CX.
1C-16

3A TROUBLESHOOTING GUIDE i
SPECIFICATIONS
^Engine model
Item ^__
FE-DOHC
FE 8-valve,
F8, F6...except
Middle East
.General
FE 12-valve
FE 8-valve F8, F6...only Middle East General

Cooling system Water cooled, forced circulation
Coolant capacity liters (US qt, Imp qt)
With heater 7.5 (7.9, 6.6) Coolant capacity liters (US qt, Imp qt) Without heater 7.0 (7.4, 6.2)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified seal
Thermostat
Type Wax, 2-stage Wax
Thermostat
Opening temperature °C(°F) Sub
.
83.5-86.5 (182-188) Main: 86.5-89.5 (188-193) 86.5-89.5 (188-193) 80.5-83.5 (177-182) Thermostat
Full-open temperature °C(°F) 100 (212) 95 (203)
Thermostat
Full-open lift
mm
(in) Sub: 1.5 (0.06) min.
Main: 8.0 (0.31) min. 8.5 (0.33) min.
Radiator
Type Corrugated
Radiator Cap valve opening pressure
kPa (kg/cm2, psi) 74-103 (0.75-1.05, 11-15)
Cooling
fan

Capacity
W

MTX 80
Cooling
fan

Capacity
W
ATX 120
Cooling
fan
Number
of
blade 4 Cooling
fan

Outer diameter
of
blade
mm
(in) MTX 320 (12.6)
Cooling
fan

Outer diameter
of
blade
mm
(in)
ATX 340 (13.4)

76G03A-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3A—
5

Coolant leakage Repair
—

Radiator fins clogged Clean 3A—
7

Radiator cap malfunction Replace 3A-
6

Cooling fan malfunction Repair 3A-12 Thermostat malfunction Replace 3 A-11
Water passage clogged Clean 3A—
5

Water
DumD
malfunction ReDair
or
replace 3A-
8
Corrosion
Impurities
in
coolant Replace 3A-
5
76G03A-004
3A—4

THERMOSTAT 3A
69G03B-010
76G03A-008
76G03A-009
THERMOSTAT
REMOVAL
1. Drain the engine coolant.
2. Remove the thermostat cover.
3. Remove the thermostat.
INSPECTION
Check the thermostat. Replace if necessary.
1. Visually check that the valve is airtight.
2. Place the thermostat and a thermometer in water.
3. Gradually heat the water and check the following:
\ Model
Item
FEDOHC
FE 8-valve F8,F6...except
Middle
East General FE 12-valve
FE 8-valve, F8,F6...only Middle East General

Initial opening
tem-
perature

Sub
valve 83.5—86.5°C (182—188°F) Main valve 86.5—89.5°C (188—193°F)
86.5—89.5°C
(188—193°F)
80.5—83.5°C (177—182°F)
Full-open
temperature 100°C (212°F) 95°C (203°F)
Full-open
lift

Sub
valve
1.5
mm
(0.06 in) min.
Main valve
8.0
mm
(0.31 in) min.
8.5
mm
(0.33
in)min.

INSTALLATION
1. Install the thermostat into the cylinder head with
jiggle pin at the top.
2. Install a new gasket with the seal print side facing
the cylinder head.
3. Install the thermostat cover.
Tightening torque:
19—30
N
m (1.9—3.1 m-kg, 14—22 ft-lb)
4. Replenish the coolant.
5. Start the engine and check for leaks.
86U03X-018
3 A-11

TROUBLESHOOTING GUIDE
3B

SPECIFICATIONS

Cooling system Water-cooled, forced circulation
Coolant capacity liters (US
qt,
Imp
qt)

With heater 9.5 (10.0, 8.4) Coolant capacity liters (US
qt,
Imp
qt)

Without heater 9.0 (9.5, 7.9)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified mechanical seal
Thermostat
Type Wax, two stage
Thermostat
Opening temperature °C(°F) Main Sub
Thermostat
Opening temperature °C(°F)
86.5-89.5 (188-193) 78.5—81.5 (173-179) Thermostat
Full-open temperature °C(°F) 100 (212) 100 (212)
Thermostat
Full-open lift
mm (in)
8.0 (0.31) min. 1.5 (0.06) min.
Radiator
Type Corrugated
fin

Radiator Cap valve opening pressure
kPa (kg/cm2,
psi)
74-103 (0.75-1.05, 11—15)
Cooling
fan

Type Electric
Cooling
fan

Capacity
W
120
Cooling
fan
Switching temprature orvopi OFF
- ON ^
91 (196) Cooling
fan

Number
of
blade 4
Cooling
fan

Outer diameter
mm
(in) 340 (13.4)

76G03B-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3B-
4

Coolant leakage Repair
—

Radiator fins clogged Clean 3B—
6

Radiator cap malfunction Replace 3B—
5

Cooling fan malfunction Repair 3B-11 Thermostat malfunction Replace 3B—
9

Water passage clogged Clean 3B—
4

Water pump malfunction ReDair
or
replace 3B—
7

Corrosion
Impurities
in
coolant Replace 3B-
4

76G03B-004
3B—3

THERMOSTAT 3B
THERMOSTAT
REMOVAL
1. Drain the engine coolant.
2. Disconnect the upper radiator hose, and water
thermo switch connector.
3. Remove the thermostat cover.
4. Remove the thermostat.
76G03B-010
76G03B-011
Sub valve Main valve
I
INSPECTION
Check the thermostat. Replace if necessary.
1. Visually check that the valve is airtight.
2. Place the thermostat and a thermometer in water.
3. Gradually heat the water and check the following:
Valve opening temperature
Sub valve : 78.5—81.5°C (173—179°F)
Main valve : 86.5—89.5°C (188—193°F)
Full open lift
Sub valve : 1.5 mm (0.06 in) min. at
100°C (212°F)
Main valve : 8 mm (0.31 in) min. at
100°C (212°F)
Valve closing temperature
Sub valve : 75°C (167°F)
Main valve : 83°C
(181
°F)
69G03B-012
76G03B-012
INSTALLATION
1. Install the thermostat into the thermostat case with
jiggle pin at the top.
2. Install a new gasket with the seal print side facing
the thermostat case.
3. Install the thermostat cover.
Tightening torque:
7—10 N-m (70—100 cm-kg, 61—87 in-lb)
4. Install the upper radiator hose and water thermo
switch connector.
5. Replenish the coolant.
6. Start the engine and check for leaks.
3B-9

OUTLINE
4A

Previous

626
Unlead-
ed

fuel
O O O O O O X O O O X

Previous

626

Leaded
fuel
O X X O O X X X O X

New
626
FE
8
Valve
Unlead-
ed

fuel
o O O O O O X X O O O

New
626
Sin-
gapore

o O X O O m O
O

(FE

&
F8)
O
O

(FE

&
F8)
O O

New
626

Middle
East
o X X O O X X X X X O

New
626

General

X
O

(FE

& F8)
X O O X
O

(FE

&
F8)
O

(FE

&
F8)
O

(FE

&
F8)
X o

New
626
ECE
&

Hong
Kong
o O X O O * O O O O O o

Remark
• Adjustment
speed:

2,200

±
100
rpm
(in
neutral).
• MTX • Operation:
Coolant
tempera-

ture

more
than

50°C

(122°F).

Mechanical
type
Installed
on
carburetor.
Improvement
of
product
quality.

Function

Allows

throttle
to
gradually
close

during

deceleration.

Reduces

CO

and
HC
emission.

Detects

electrical
signal
from
in-
put
devices
and
controls
output
devices. Supplies
exhaust
gas
to
intake
manifold
to
reduce
NOx

Filters

fuel

Provides

fuel
to
carburetor.
Detects
when
throttle
valve
fully
closed. Opens
fuel

passage

to
secon-
dary
stage
of
carburetor.
Controls
shutter
valve
by
intake

air
temperature. Prevents
carburetor

icing.

Supplies
fresh
air
to
exhaust
manifold
to
reduce
CO
and
HC
emissions. Prevents
fuel
from
flowing
into

two-way

or
three-way
check

valve

Component

Dashpot Engine
Contorol
Unit

EGR

Control
Valve

Fuel

Filter

Fuel

Pump
Idle
Switch

Idle-up

Solenoid

Valve
Intake
Air
Temperature
Control
Valve

PTC

Heater

Reed

Valve

Separator

•a a> a -a .2-S
3
9-a a) 5 u- O UJ
z

Ox

111 IL •a c x" Ul
V (-
U.ps •o u.
-
X
_ X
I-
o-t-
s ®
s
*
o *
oo
x to
U. UJ
u.
T- oi CO
4 A—13

4 A AUTO-RETURN CHOKE SYSTEM
AUTO-RETURN CHOKE SYSTEM
[FE 8VALVE—UNLEADED FUEL, MIDDLE EAST, and F6—GENERAL]
r ~ I
76G04A-066
An auto-return choke is adopted to prevent the catalytic converter from over-heating because of over
use of the choke. This system opens the choke valve by causing the choke knob to return when the
engine coolant temperature is more than 67°C (153°F).
TROUBLESHOOTING
Note
Make the system inspection first. If no problem is found, continue with the next inspec-
tion of the Troubleshooting Guide. (Refer to pages 4A—16, 21, or 22)
Possible cause
" ^ Page
Symptom
System inspection Choke magnet Water thermo switch
Possible cause
" ^ Page
Symptom 4A—40 4A—41 4A—41
Checking order 1 2 3
76G04A-067
System Inspection
1. Make sure that the engine is cold and turn the ig-
nition switch ON.
2. Pull out the choke knob and check that it is held on.
3. Start the engine and check that the choke knob
returns during warming-up.
76G04A-068
4A—40

PTC HEATER SYSTEM 4A
System Inspection
Except FE 8Valve—Unleaded Fuel
1. Connect a voltmeter to the PTC heater connector.
2. Start the engine and measure the voltage.
Specification
Radiator coolant
temperature Below 17°C (63°F) Above
17°C (63°F)
Voltage Approx. 12V ov
76G04A-073
FE 8Valve—Unleaded Fuel
1. Start the engine.
2. Connect a voltmeter to the PTC heater connector
terminals and measure the voltage.
Voltage
Engine coolant
temperature
Below 67°C (152°F)
Above 67°C (152°F)
Radiator coolant temperature Below 17°C (63°F) Above 17°C (63°F) —
Terminal BrB Approx.
12V
OV OV Terminal BrW
Approx.
12V Approx. 12V OV
76G04A-074
PTC Heater
Except FE 8Valve—Unleaded Fuel
1. Disconnect the PTC heater connector.
2. Check for continuity of the heater with an
ohmmeter.
76G04A-075
FE 8Valve—Unleaded Fuel
1. Disconnect the PTC heater connector.
2. Check for continuity between terminal wire (BrW)
and a ground.
3. Check for continuity between terminal wire (BrB)
and (B).
76G04A-076
4A—43

4 A DECELERATION CONTROL SYSTEM
Solenoid valve (for main air bleed control system)
76G04A-094
76G04A-095
76G04A-191
System Inspection
1. Disconnect the vacuum switch connector.
2. Make sure that radiator coolant temperature is be-
low 17°C (63°F).
3. Disconnect the upper vacuum hose from the sole-
noid valve.
4. Place a finger over the solenoid valve open port
and check that vacuum is not felt when engine is
running.
5. Warming up the engine.
6. Place a finger over the same open port of the sole-
noid valve and check that weak vacuum is felt.
7. Reconnect the vacuum switch connector.
8. Check that weak vacuum is felt at the open port
of the solenoid valve at idle.
9. Accelerate the engine rapidly and check that vacu-
um is not felt.
Solenoid Valve (A/C)
1. Disconnect vacuum hose A (White) from the car-
buretor.
2. Disconnect vacuum hose B from the solenoid
valve.
3. Disconnect the solenoid valve connector.
4. Blow air through the valve from hose A and check
that it comes out of port C.
5. Apply 12V and ground to the solenoid valve with
jumper wires.
6. Blow air through the valve from hose A and check
that air not come out.
7. Replace if necessary.
76G04A-192
4A—52