light MAZDA MODEL 6 2015 Smart Start Guide (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL 6, Model: MAZDA MODEL 6 2015Pages: 42, PDF Size: 6.01 MB
Page 2 of 42

1
KEYLESS ENTRY SYSTEM
• This system allows you to lock and unlock the doors by pushing the
desir ed buttons.
Key
Unlock
• Push once
to unlock
driver’s door
or all the doors
(depending on
personalization
setting).
•
Push
twice
(within three
seconds) to
unlock all doors.
Panic Alarm
• Push for one
second or more
to activate alarm.
•
Push
Lock,
Unlock, or Panic
Alarm to turn
alarm off.
Tr u n k
• Push and hold to
open the trunk.
Lock
• Push once to
lock all doors.
•
Push
twice
(within five
seconds) for horn
sound verification
that all doors
are locked.
NOTE: Refer to your Owner’s Manual for additional details about
“Personalization Features”.
CAUTION:
•
Make sure vehicle is OFF and take
the keyless entry system key with
you when leaving the vehicle.
•
When locking doors using inside
door switches or inside door
-lock
knobs, be careful not to leave the
key inside the vehicle.
CAUTION: RED
Key Indicator Light may illuminate if either advance key
or keyless entry key is placed in the cup holder. The key can sometimes not
be detected in the cup holder.
Inside Door
Lock Switch
Lock
Unlock
1660320_15b_Mazda6_SSG_021714.indd 12/17/14 11:10 AM
Page 4 of 42

3
STARTING THE ENGINE WITH
ACCELERATED WARM-UP SYSTEM (AWS)
The Mazda6 is equipped with SKYACTIV combustion technology. This
technology includes AWS (Accelerated Warm-up System) for optimal
emission performance during cold starting conditions.
While Carrying the Key…
• Start the engine by pushing the START/STOP ENGINE button while
p ushing the clutch pedal (M/ T) or the brake pedal (A / T).
Wh
at you will notice? On start-up, the engine speed and sound are
higher (1500 RPM) for less than 1 minute to quickly bring the catalyst
to efficient operating temperature. The RPM will reduce to idle once the
temperature is achieved. This is normal engine operation under cold
start conditions.
Wh
at this does? This heats up the catalytic converter faster to reduce
emissions and allows Mazda to use an exhaust header on the engine (to
improve efficiency and horsepower).
NOT
E:
Yo u can drive the vehicle during AWS activation, no need to wait.
Key
• Shut the engine OFF by setting the parking brake/placing the
v
ehicle in Park (A / T), then push the START/STOP ENGINE button.
•
Ac
tivate Accessories (ACC) by pushing the START/STOP
ENGINE button once without pushing the clutch or brake pedal.
•
Tu
rn the ignition to the ON position by pushing the START/STOP
ENGINE button twice without pushing the clutch or brake pedal.
The key indicator light
in the instrument cluster will show GREEN
(engine ready to start) when the key is detected and the clutch pedal (M/ T)
or the brake pedal (A / T) is pushed. If the KEY warning light illuminates
RED , or the START/STOP ENGINE button indicator light flashes AMBER ,
this could indicate a problem with the engine starting system and the
inability to start the engine or switch the ignition to ACC or ON. Have your
vehicle inspected at an Authorized Mazda Dealer as soon as possible.
N
OTE:
RED Key Indicator Light may flash if the key is placed in the cup holder.
The key may not be detected in the cup holder .
1660320_15b_Mazda6_SSG_021714.indd 32/17/14 11:10 AM
Page 5 of 42

4
www.MazdaUSA.com
FUEL ECONOMY:
To achieve the best fuel economy,
visit www.fueleconomy.gov for
more information.
BREAK-IN PERIOD
No special break-in is necessary,
but a few precautions in the first
600 miles should be observed.
•
Do n
ot race the engine.
•
Do n
ot maintain one constant
speed, either slow or fast,
for a long period of time.
•
Av
oid full-throttle starts.
•
Av
oid unnecessary hard stops.
•
Do n
ot drive constantly at
full-throttle or high engine rpm
for extended periods of time.
Emergency Engine Stop
Pushing and holding the
START/STOP ENGINE button or
repeatedly pushing the button while
the engine is running will turn the
engine OFF. Use only in case of
an emergency.
Emergency Vehicle Entry
If the key cannot be used due to
a malfunction or dead key battery,
use the auxiliary key to lock or
unlock the doors.
Emergency Engine Start
If the engine cannot be started
due to a dead key battery:
1 Push the brake pedal (A / T)
o r the clutch pedal (M/ T).
2
Wh
ile the indicator light flashes
GREEN , touch the START/STOP
ENGINE button using the back
side of the transmitter
(as shown).
3 A
fter the GREEN indicator light
illuminates constantly, push the
START/STOP ENGINE button with
your finger to start the engine.
Auxiliary Key Release
Auxiliary Key
Key (Rear)
START/STOP ENGINE Button
Indicator Light
Transmitter
1660320_15b_Mazda6_SSG_021714.indd 42/17/14 11:10 AM
Page 7 of 42

6
www.MazdaUSA.com
INFO (if equipped)
Toggle INFO button up or down on steering wheel to display the following
(actual displayed information will vary on your vehicle):
Push the center of the INFO
button to make selections.
INFO
Button
Customize the following vehicle functions
using the audio SETUP button:
•
Door Locks
•
Lighting Control
•
Wiper Contr
ol
Distance to Empty
Average MPG
Current MPG
Average Speed
Settings
SeatsInformation Display
VEHICLE PERSONALIZATION FEATURES
Customize the following vehicle functions using
Information Display “Settings”:
• Re
set Averages
• Op
tional Screen
• Sm
art City Brake
• Vo
lumes
• Bl
ind Spot Monitoring
• Un
its
• Ma
intenance
• Re
store Defaults
Refer to the Owner’s Manual for a complete list of
Personalization Feature items.
1660320_15b_Mazda6_SSG_021714.indd 62/17/14 11:11 AM
Page 8 of 42

7
Driver’s View
LIGHTING/
TURN SIGNALS
( P. 11 )
BLUETOOTH®
HANDS-FREE/
AUDIO
( P P. 2 9 - 3 0 )
INFORMATION D I S P L AY
( P. 6 )
TRUNK
RELEASE
HOOD
RELEASE
FUEL DOOR
RELEASE TILT/TELESCOPING
STEERING WHEEL
LEVER
BSM
( P. 2 1LDWS
( P. 17 )
TPMS SET
( P. 1 6 )
NAVIGATION
SYSTEM SD CARD
( P. 3 1 )
AFS
( P. 1 5 )
DSC
OFF
( P. 2 4 )
CRUISE
CONTROL
1660320_15b_Mazda6_SSG_021714.indd 72/17/14 11:11 AM
Page 9 of 42

8
Driver’s View
CLOCK ( P. 3 0 )
NAVIGATION/AUDIO
(WITH 5.8” LCD)
(PP. 27-28, 31-32)
CLIMATE CONTROL ( P P. 2 3 - 2 4 )S E AT
WARMERS
www.MazdaUSA.com
PASSENGER AIRBAG
OFF INDICATOR1
HAZARD
WARNING
AUDIO
(WITHOUT 5.8” LCD)
( P P. 2 5 - 2 8 )
ACCESSORY
SOCKET
1 This indicator light illuminates to remind you that the fr ont passenger’s front/side airbags
and seat belt pretensioner will not deploy during a collision. The reason for this is that the
weight in the seat is less than approximately 66 lbs. Always wear your seat belt and secure children in the rear
seats in appropriate child restraints. See the Owner’s Manual for important information on this safety feature.
NOTE:
Indicator light turns of f when conditions have been met for necessar y airbag deployment. See
Owner’s Manual for further information.
PUSH
BUTTON
S TA R T
( P. 3 - 4 )
WIPER/
WASHER
( P. 1 2 )
1660320_15b_Mazda6_SSG_021714.indd 82/17/14 11:11 AM
Page 10 of 42

9
SHIFT POSITION
INDICATOR LIGHT SPEEDOMETER
Instrument Cluster
TACHOMETERAMBIENT
TEMPERATURE
TYPE A & B CLUSTER GLOSSARY WARNING AND INDICATOR LIGHTS
NOTE:
See Owner’s Manual for more details and explanations.
Type A cluster is
shown. Type B
cluster is similar,
but with warning
lights in different
locations.
The instrument cluster has a dimmer function that can be
cancelled to make the illumination brighter during the day
when the headlights are on. If the illumination
is too dim during the day, push the knob,
or if the illumination does not dim when
turning on the headlights at night,
push the knob. When dimmed,
rotate the knob to adjust the
brightness of the illumination.
Lan e Departure Warning
System On ( AMBER)/
Lane Detected ( GREEN) ( p . 17 )
AFS
OFF
Ad
aptive Front Lighting System
(AFS) OFF ( p. 14)
Tr action Control System (TCS)/
Dynamic Stability Control (DSC) On: TCS/DSC malfunction
Flashing: TCS/DSC operating
BSM OFF
BS
M OFF (Blind Spot
Monitoring) (pp. 25-26)
OFF
Dy
namic Stability Control
(DSC) Off Indicator Light SPORT Mode On ( p. 19)
Lights On (Exterior) ( p . 11)
High Beam Control On ( p. 13)
Headlight High Beams On
Air Bag/Front Seat Belt
P
retensioner System
Malfunction
Ch eck Engine Light
Se at Belt Unbuckled/
Malfunction
Tu rn Signals/Hazard
Warning Indicator Lights
Ti re Pressure Monitoring System
(TPMS) Warning Light* ( p. 18) On/ Warning Beep: Low tire pressure in one
or more tires. Flashing: TPMS Malfunction
Cr uise Main Indicator Light
On ( AMBER )/Cruise Set
Indicator Light On ( GREEN)
Mazda Radar Cruise Control Wa
rning Light On ( AMBER)
Se
t Indicator ( GREEN)
(pp. 15-16)
ABS (Antilock Brake
S ystem) Malfunction
Sh ift Position Indicator Light
Sec urity Indicator Light
*TPMS NOTE:
Low ambient temperature and/or high altitude causes tire pressures to drop
and may turn the TPMS warning light on. If the warning light comes on, check the tire pressure
and fill the tires as soon as possible, preferably before moving the vehicle and warming up
the tires. Initialize system (p. 16). Tire pressure should be checked when the tires are cold.
1660320_15b_Mazda6_SSG_021714.indd 92/17/14 11:12 AM
Page 11 of 42

10
DASHBOARD ILLUMINATION/
DIMMER1/TRIP METER2
1 • Rotate the knob to adjust the brightness of the
instrument cluster and other dashboard illuminations.
2 • Push to toggle between trip meter (A & B). • When a trip meter is selected, push and hold
to r
eset to zero.
www.MazdaUSA.com
Br ake Warning Light
Parking brake on/low brake
fluid/malfunction
Master Warning Light
Low Fuel Level
TYPE B INSTRUMENT CLUSTER
WARNING LIGHTS ONLY.
These warnings are displayed as text in the Type
A Information display.
Lo w Engine Oil Pressure
Po wer Steering Malfunction
Au tomatic Transaxle
Warning Light
Cha rging System
Malfunction
Doo r/Trunk Ajar
Lo w Washer Fluid Level
Warning Light
KEY Warning Light RED
KE Y Indicator Light GREEN
Check Fuel Cap
P erform Maintenance FUEL
GAUGE
ODOMETER/
TRIP METER
ENGINE COOLANT TEMP LIGHTS Since this vehicle does not use an
engine coolant temperature gauge, red
and blue engine coolant temperature
lights are used to indicate high
and low coolant temperature.
Red Coolant Temp Light Flashing: Engine is starting
to run hot. Drive slowly to
reduce engine load.
On: E
ngine is overheating. Safely pull
over to the side of the road and turn
the engine off. Refer to the Owner’s
Manual for more information.
Blue Coolant Temp Light On: Engine coolant is cold
and no warm air is available
for heater/defroster.
Of
f: Engine coolant is warm and
warm air is available for heater/
defroster. The light may stay on for a
few minutes after start-up when the
engine is cold, but the vehicle can
be driven with the light on or off.
INFORMATION D I S P L AY
See page 6 or the
Owner’s Manual for
further information.
TYPE B CLUSTER
INFORMATION D I S P L AY
1660320_15b_Mazda6_SSG_021714.indd 102/17/14 11:12 AM
Page 12 of 42

11
Lights
LIGHTING CONTROL/TURN SIGNAL LEVER
: Turns tail, parking, dashboard,
a nd headlights on.
: Turns tail,
p
arking, and
dashboard
lights on.
Pull
to Flash
High BeamsPush for
High Beams
NOTE: The DRL (Daytime Running Lights) automatically turn on when the ignition is
switched ON. To disable/enable this feature see your Authorized Mazda Dealer.
AUTO: The light sensor
automatically determines
when to turn the headlights
on or off.: Turns fog lights
on
only when
headlights
are on.
Smart Turn: To signal a lane
change, push the turn signal lever
up or down halfway and release.
After releasing the lever, the turn
signal indicator will flash three times.
(Refer to page 6 or Owner’s Manual
for “Personalization Features”)
1660320_15b_Mazda6_SSG_021714.indd 112/17/14 11:12 AM
Page 14 of 42

13
High Beam Control
1. Turn the headlight
switch to the
AUTO position.
2. Pus
h the headlight
lever forward to the
High Beam position.
When the HBC system is on, the HBC indicator light in the instrument
cluster will illuminate (
GREEN). The High Beam indicator light will turn On
(BLUE) when the HBC system switches to high beam and will turn Off when
the HBC system switches to low beam.
HIGH BEAM CONTROL (HBC) (if equipped)
While driving the vehicle at speeds above 18 mph (30 km/h), the headlights
are switched to high beams when there are no vehicles in front of your
vehicle or approaching in the opposite direction.
The HBC system switches to low beam when:
•
The
system detects a vehicle or the headlights/lights of a vehicle
approaching in the opposite direction.
•
Dr
iving on roads lined with street lights or well-lit cities and towns.
•
At s
peeds of 12 mph (20 km/h) or lower.
OPERATIONAUTO
FORWARD
1660320_15b_Mazda6_SSG_021714.indd 132/17/14 11:12 AM