MAZDA MODEL 626 2002 Owners Manual

6-5
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G





Oscillating Air Vent
The air from the center ventilation vent
can automatically be swung in both right
and left directions.
To turn on, push the switch in.
Another push will turn it off. When the
switch is turned off, the direction of
airflow can manually be adjusted by the
thumb wheel.
NOTE
When the switch is turned on, the vent
always swings even when no air comes
out from the center ventilation.
J94S.book Page 5 Saturday, June 23, 2001 1:04 PM

6-6
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G





Control Switches
Fan control dial
This dial allows variable fan speeds.
0—Fan off
1—Low speed
2—Medium low speed
3—Medium high speed
4—High speed Temperature control dial
This dial controls temperature of the air
coming through the system. Turn it
clockwise for hot (red) and
counterclockwise for cold (blue).
Manual Type
Fan control dial
Mode selector switch
Mode selector switch
Temperature control dial
Air conditioner switchAir intake selector switch
Hot
Cold
J94S.book Page 6 Saturday, June 23, 2001 1:04 PM

6-7
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G
Mode selector switch
Press the mode selector switch to select
airflow mode (page 6-4).
Air conditioner switch
Press the switch to turn the air conditioner
on. An indicator light on the switch will
illuminate when the fan switch is on.
Press the switch once again to turn the air
conditioner off.Air intake selector switch
This switch controls the source of air
entering the vehicle.
The switch should be kept in the outside
air position under normal conditions.
Press the switch to alternate between the
two positions. The indicator light
illuminates when the recirculated air
position is selected.
Outside air position
This position is automatically selected
when the ignition switch is turned to the
ON position.
Use it for normal ventilation and heating.
The indicator light is out when the outside
air position is selected.
Recirculated air position
This position recirculates air within the
vehicle. Don
’t use the recirculated air
position for long periods when the vehicle
is stopped.
The indicator light is on when the
recirculated air position is selected.
NOTE
The air conditioner may not function
when the outside temperature
approaches 0 ° C (32 °F).
J94S.book Page 7 Saturday, June 23, 2001 1:04 PM

6-8
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G





Heating
1. Set the mode selector switch to the
position.
2. Set the temperature control dial to the hot position.
3. Set the fan control dial to the desired speed.






Cooling (With Air Conditioner)
1. Set the mode selector switch to the
position.
2. Set the temperature control dial to the desired position.
3. Set the fan control dial to the desired speed.
4. Turn on the air conditioner.
The Recirculated Air Position: Using the recirculated air position in
cold weather will cause the glass to
fog up. Your vision will be hampered,
which could lead to a serious
accident. Do not use the recirculated
air position in cold weather.
WARNINGNOTE
• If the windshield fogs up easily, set
the mode selector switch to the
position.
• If cooler air is desired at face level,
set the mode selector switch at the
position and adjust the
temperature control dial to maintain
maximum comfort.
• The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
• In the position, the outside air
is automatically selected.
J94S.book Page 8 Saturday, June 23, 2001 1:04 PM

6-9
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G
5. Adjust the fan control dial and temperature control dial to maintain
maximum comfort.




Ventilation
1. Set the mode selector switch to the
position.
2. Set the air intake selector switch to the outside air position (indicator light off).
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.






Windshield Defrosting and
Defogging
When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-21).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner
off.
NOTE
• When maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set
the air intake selector switch to the
recirculated air position, then set the
fan control dial to the position 4.
• If warmer air is desired at floor
level, set the mode selector switch
at the position and adjust the
temperature control dial to maintain
maximum comfort.
• The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
CAUTION
J94S.book Page 9 Saturday, June 23, 2001 1:04 PM

6-10
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G
1. Set the mode selector switch to the position.
2. Set the temperature control dial to the desired position.
3. Set the fan control dial to the desired speed.




Dehumidifying (With Air
Conditioner)
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector switch to the
desired position.
2. Set the air intake selector switch to the outside air position (indicator light off).
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.
5. Turn on the air conditioner.
Foggy Windshield:Using the position with the
temperature control set to the cold
position will cause the outside of the
glass to fog up. Your vision will be
hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the position.
NOTE
• For maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
• If warm air is desired at the floor,
set the mode selector switch to the
position.
• In the or position, the
outside air is automatically selected.
The air intake selector switch
cannot be changed to the
recirculated air position.
WARNING
J94S.book Page 10 Saturday, June 23, 2001 1:04 PM

6-11
Interior Comfort
Form No. 8Q50-EA-01G
Audio System





Rear Window Antenna
The rear window antenna receives both
AM and FM signals.




Radio Reception
AM characteristics
AM signals bend around such things as
buildings or mountains and bounce off the
ionosphere. Therefore, they can reach
longer distances than FM signals. Because
of this, two stations may sometimes be
picked up on the same frequency at the
same time.
FM characteristics
An FM broadcast range is usually about
40—50 km (25 —30 miles) from the
source. Because of extra coding needed to
break the sound into two channels, stereo
FM has even less range than monaural
(non-stereo) FM.
Antenna
When washing the inside rear window,
use a soft cloth dampened in lukewarm
water, gently wiping the antenna lines.
Use of glass cleaning products could
damage the antenna.
CAUTION
Operating Tips for Audio
System
Ionosphere
Station 1 Station 2
FM Station
40—50 km
(25—30 miles)
J94S.book Page 11 Saturday, June 23, 2001 1:04 PM

6-12
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
Signals from an FM transmitter are
similar to beams of light because they do
not bend around corners, but they do
reflect. Unlike AM signals, FM signals
cannot travel beyond the horizon.
Therefore, FM stations cannot be received
at the great distances possible with AM
reception.
Atmospheric conditions can also affect
FM reception. High humidity will cause
poor reception. However, cloudy days
may provide better reception than clear
days.
Multipath noise
Since FM signals can be reflected by
obstructions, it is possible to receive both
the direct signal and the reflected signal at
the same time. This causes a slight delay
in reception and may be heard as a broken
sound or a distortion. This problem may
also be encountered when in close
proximity to the transmitter.Flutter/Skip noise
Signals from an FM transmitter move in
straight lines and become weak in valleys
between tall buildings, mountains, and
other obstacles. When a vehicle passes
through such an area, the reception
conditions may change suddenly,
resulting in annoying noise.
Wea k si gn a l no i s e
In suburban areas, broadcast signals
become weak because of distance from
the transmitter. Reception in such fringe
areas is characterized by sound breakup.
Ionosphere
100—200 km (60—120 miles)
FM wave
FM wave AM wave
Direct
Reflected wave
J94S.book Page 12 Saturday, June 23, 2001 1:04 PM

6-13
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
Strong signal noise
This occurs very close to a transmitter
tower. The broadcast signals are
extremely strong, so the result is noise and
sound breakup at the radio receiver.
Station drift noise
When a vehicle reaches the area of two
strong stations broadcasting at similar
frequencies, the original station may be
temporarily lost and the second station
picked up. At this time there will be some
noise from this disturbance.




Operating Tips for Cassette Tape
Player
Cleaning the cassette tape player
The tape head, capstans, and pinch rollers
will gather oxide residue from cassette
tapes. This can cause weak or wavering
sounds and damage to the cassette tapes
and player. Use a good quality head-
cleaning tape or a liquid cleaner cassette
tape to remove it.
Should the unit not operate normally,
consult an Authorized Mazda Dealer.
Never attempt to repair it or insert a
screwdriver or anything else.
Handling the cassette tape player
The following precautions should be
observed.
• Do not spill any liquid on the audio
system.
• Do not insert any objects, other than
cassette tape, into the slot.
Station 1
88.1 MHz Station 2
88.3 MHz
J94S.book Page 13 Saturday, June 23, 2001 1:04 PM

6-14
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
•If the cassette tape is loose, it may
produce poor sound or performance
during playback. Use a pencil or
something similar to remove any slack.
• Only cassette tapes that play no longer
than 90 minutes should be used.
Cassette tape exceeding 90 minutes are
thin and may easily break.
• Do not leave a cassette tape in the tape
player slot when not in use. Remove it
completely to permit the slot door to
close and to protect the mechanism
from dust.
• Store cassette tape away from extreme
heat, magnetic fields, and direct
sunlight. Protect the exposed cassette
tape from dirt and damage. Store
cassette tapes in their original cases or
other protective cases.
• Insert only cassette tapes into the slot.
If objects other than cassette tapes are
inserted, they may damage the player.




Operating Tips for Mini Disc
(MD) Player
• The MD player has been designed to
play MDs bearing the identification
logo as shown. No other MDs can be
played.
• When inserting the MD, make sure the
MD label is facing up, and the MD is
oriented to the insertion slot in the
direction of the arrow. If not inserted
correctly, the MD will be ejected, or
may remain stuck in the MD deck.
• Do not touch the internal part of the
MD. If the MD shutter is slid open for
no reason, it may be broken.
J94S.book Page 14 Saturday, June 23, 2001 1:04 PM