warning MAZDA MODEL CX-5 2013 (in English) Manual PDF

Black plate (128,1)
NOTElThe key must be carried because the key
carries an immobilizer chip that must
communicate with the engine controls at
short range.
lThe engine can be started when the push
button start is pressed from off, ACC, or
ON.
lThe advanced keyless entry system
functions can be deactivated to prevent any
possible adverse effect on a user wearing a
pacemaker or other medical device. If the
system is deactivated, you will be unable to
start the engine by carrying the key.
Consult an Authorized Mazda Dealer for
details. If the advanced keyless entry system
has been deactivated, you can start the
engine by following the procedure indicated
when the key battery goes dead.
Refer to Engine Start Function When Key
Battery is Dead on page 4-6.
lAfter starting a cold engine, the engine
speed increases and a whining sound from
the engine compartment can be heard.
This is for improved exhaust gas
purification and does not indicate defect of
the parts.
lEngine-starting is controlled by the spark
ignition system.
This system meets all Canadian
Interference-Causing Equipment Standard
requirements regulating the impulse
electrical field strength of radio noise.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on.
4. Continue to press the brake pedal
firmly until the engine has completely
started.5.(Manual transaxle)
Continue to press the clutch pedal
firmly until the engine has completely
started.
(Automatic transaxle)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
(Manual transaxle)
The starter will not operate if the clutch pedal
is not depressed sufficiently.
(Automatic transaxle)
The starter will not operate if the shift lever is
not in P or N and the brake pedal is not
depressed sufficiently.
6. Verify that the KEY indicator light
(green) in the instrument cluster and
the push button start indicator light
(green) illuminate. Refer to Warning/
Indicator Lights on page 4-15. If the
push button start indicator light (green)
flashes, make sure that the key is being
carried. If the push button start
indicator light (green) flashes with the
key being carried, touch the key to the
push button start and start the engine.
Refer to Engine Start Function When
Key Battery is Dead on page 4-6.
4-4
When Driving
Start/Stop Engine
CX-5_8CA5-EA-11L_Edition3 Page128
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (129,1)
CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate a problem with the
engine starting system and the
inability to start the engine or switch
the ignition to ACC or ON. Have your
vehicle inspected at an Authorized
Mazda Dealer as soon as possible.NOTE
lUnder the following conditions, the KEY
warning light (red) flashes after the push
button start is pressed to inform the driver
that the push button start will not switch to
ACC even if it is pressed from off.
lThe key battery is dead.lThe key is out of operational range.lThe key is placed in areas where it is
difficult for the system to detect the
signal (page 3-7).
lA key from another manufacturer similar
to the key is in the operational range.
l(Forced engine starting method)
If the KEY warning light (red) illuminates,
or the push button start indicator light
(amber) flashes, this could indicate that the
engine may not start using the usual
starting method. Have your vehicle
inspected at an Authorized Mazda Dealer
as soon as possible. If this occurs, the
engine can be force-started. Press and hold
the push button start until the engine starts.
Other procedures necessary for starting the
engine such as having the key in the cabin,
and depressing the clutch pedal (manual
transaxle) or the brake pedal (automatic
transaxle) are required.
lWhen the engine is force-started, the KEY
warning light (red) remains illuminated and
the push button start indicator light
(amber) remains flashing.
l(Automatic transaxle)
When the shift lever is in the neutral (N)
position, the KEY indicator light (green)
and the push button start indicator light
(green) do not illuminate.
7. Press the push button start after both
the KEY indicator light (green) in the
instrument cluster and the push button
start indicator light (green) illuminate.
When Driving
Start/Stop Engine
4-5
CX-5_8CA5-EA-11L_Edition3 Page129
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (132,1)
Turning the Engine Off
WARNING
Do not stop the engine while the
vehicle is moving:
Stopping the engine while the vehicle
is moving for any reason other than
in an emergency is dangerous.
Stopping the engine while the vehicle
is moving will result in reduced
braking ability due to the loss of
power braking, which could cause an
accident and serious injury.
1. Stop the vehicle completely.
2.(Manual transaxle)
Shift into neutral.
(Automatic transaxle)
Shift the shift lever to the P position.
3. Press the push button start to turn off
the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure
the push button start is pressed to
off.NOTE
lThe electrical fan in the engine
compartment could turn on for a few
minutes after the ignition is switched from
ON to OFF, whether or not the A/C is on or
off, to cool the engine compartment quickly.
lWhen the push button start is pressed to off
from ON, the KEY indicator light (green)
flashes for approximately 30 seconds
indicating that the remaining battery power
of the key is low. Replace with a new
battery before the key becomes unusable.
Refer to Replace electrical battery (page
6-33).
l(Automatic transaxle)
If the engine is turned off while the shift
lever is in a position other than P, the
ignition switches to ACC.
qEmergency Engine Stop
Continuously pressing the push button
start while the engine is running or the
vehicle being driven, or quickly pressing
it any number of times will turn the
engine off immediately. The ignition
position will be ACC.
4-8
When Driving
Start/Stop Engine
CX-5_8CA5-EA-11L_Edition3 Page132
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (135,1)
qTachometer
The tachometer shows engine speed in
thousands of revolutions per minute
(rpm).
Red zone
CAUTION
Do not run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine
damage.
qFuel Gauge
The fuel gauge shows approximately how
much fuel is remaining in the tank when
the ignition is switched ON. We
recommend keeping the tank over 1/4 full.
Full
1/4 Full
If the low fuel warning light illuminates or
the fuel level is very low, refuel as soon as
possible.
Refer to Warning/Indicator Lights on page
4-15.
NOTE
lAfter refueling, it may require some time for
the indicator to stabilize. In addition, the
indicator may deviate while driving on a
slope or curve since the fuel moves in the
tank.
lThe direction of the arrow () indicates
that the fuel-filler lid is on the left side of
the vehicle.
qDashboard Illumination
Rotate the knob to adjust the brightness of
the instrument cluster and other
illuminations in the dashboard.
NOTE
lThe brightness of dashboard illuminations
can be adjusted when the headlight switch
is in the
orposition.lWhen the dashboard illumination
brightness cannot be adjusted any more, a
beep sound will be heard.
Dim
Bright
When Driving
Instrument Cluster and Display
4-11
CX-5_8CA5-EA-11L_Edition3 Page135
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (137,1)
qTrip Computer and INFO Switch
The following information can be selected
by pressing the up
or downpart of
the INFO switch with the ignition
switched ON.
lThe approximate distance you can
travel on the available fuel.
lThe average fuel economy.lThe current fuel economy.lThe average vehicle speed.
If you have any problems with your trip
computer, consult an Authorized Mazda
Dealer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.
The distance-to-empty will be calculated
and displayed every second.
NOTElEven though the distance-to-empty display
may indicate a sufficient amount of
remaining driving distance before refueling
is required, refuel as soon as possible if the
fuel level is very low or the low fuel
warning light illuminates.
lThe display will not change unless you add
more than approximately 10 L (2.6 US gal,
2.2 Imp gal) of fuel.
lThe distance-to-empty is the approximate
remaining distance the vehicle can be
driven until all the graduation marks in the
fuel gauge indicating the remaining fuel
supply disappear.
Average fuel economy mode
This mode displays the average fuel
economy by calculating the total fuel
consumption and the total traveled
distance since purchasing the vehicle, re-
connecting the battery after disconnection,
or resetting the data. The average fuel
economy is calculated and displayed
every minute.
To clear the data being displayed, press
the INFO button for more than 1.5
seconds.
When Driving
Instrument Cluster and Display
4-13
CX-5_8CA5-EA-11L_Edition3 Page137
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (139,1)
Warning/Indicator Lights
Warning/Indicator lights will appear in any of the highlighted areas
Signal Warning/Indicator Lights Page
Brake System Warning Light 4-17
Master Warning Light 4-18
Antilock Brake System (ABS) Warning Light 4-18
Charging System Warning Light 4-19
Engine Oil Pressure Warning Light 4-19
Check Engine Light 4-20
High Engine Coolant Temperature Warning Light (Red) 4-20
When Driving
Instrument Cluster and Display
4-15
CX-5_8CA5-EA-11L_Edition3 Page139
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (140,1)
Signal Warning/Indicator Lights Page
AWD Warning Light 4-21
Automatic Transaxle Warning Light 4-21
Power Steering Malfunction Indicator Light 4-22
Air Bag/Front Seat Belt Pretensioner System Warning Light 4-22
Low Fuel Warning Light 4-18
Check Fuel Cap Warning Light 4-23
Seat Belt Warning Light 4-23
Door-Ajar Warning Light 4-24
Low Washer Fluid Level Warning Light 4-25
Tire Pressure Monitoring System Warning Light 4-25
KEY Warning Light (Red)/Indicator Light (Green) 4-26
Traction Control System (TCS)/Dynamic Stability Control (DSC) Indicator
Light4-27
Traction Control System (TCS) OFF Indicator Light 4-28
Adaptive Front Lighting System (AFS) OFF Indicator Light 4-28
Low Engine Coolant Temperature Indicator Light (Blue) 4-28
Shift Position Indicator Light 4-28
4-16
When Driving
Instrument Cluster and Display
CX-5_8CA5-EA-11L_Edition3 Page140
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (141,1)
Signal Warning/Indicator Lights Page
Headlight High-Beam Indicator Light 4-29
Turn Signal/Hazard Warning Indicator Lights 4-29
Security Indicator Light 4-29
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 4-29
Blind Spot Monitoring (BSM) System OFF Indicator Light 4-30
Lights-On Indicator Light 4-30
qWarning (Display Indication)
Message information such as system
operations or malfunctions is indicated in
the display. Check the vehicle condition
or have the vehicle inspected at an
Authorized Mazda Dealer according to
the indication.
qBrake System Warning Light
This warning has the following functions:
Parking brake warning
The light illuminates when the parking
brake is applied with the ignition switched
to START or ON. It turns off when the
parking brake is fully released.
Low brake fluid level warning
If the light stays on after the parking brake
is fully released there may be a problem
with the brakes.
Drive to the side of the road and park off
the right-of-way.
You may notice that the pedal is harder to
depress or that it may go closer to the
floor. In either case, it will take longer to
stop the vehicle.
1. With the engine stopped, open the
hood and check the brake fluid level
immediately, and then add fluid if
required (page 6-25).
2. After adding fluid, check the light
again.
If the warning light remains on, or if the
brakes do not operate properly, do not
drive the vehicle. Have it towed to an
Authorized Mazda Dealer.
When Driving
Instrument Cluster and Display
4-17
CX-5_8CA5-EA-11L_Edition3 Page141
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (142,1)
Even if the light turns off, have your
brake system inspected as soon as
possible by an Authorized Mazda Dealer.
NOTE
Having to add brake fluid is sometimes an
indicator of leakage. Consult an Authorized
Mazda Dealer as soon as possible even if the
brake light is no longer illuminated.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible:
Driving with the brake system
warning light illuminated is
dangerous. It indicates that your
brakes may not work at all or that
they could completely fail at any
time. If this light remains
illuminated, after checking that the
parking brake is fully released, have
the brakes inspected immediately.
qMaster Warning Light
This warning light stays on for a few
seconds when the ignition is switched
ON.
The light illuminates continuously if any
one of the following occurs. Consult an
Authorized Mazda Dealer.
lThere is a malfunction in the battery
management system.
lThere is a malfunction in the brake
switch.
qABS Warning Light
The warning light stays on for a few
seconds when the ignition is switched
ON.
If the ABS warning light stays on while
you're driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function normally
as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
NOTE
When the engine is jump-started to charge the
battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it
is the result of the weak battery and does not
indicate an ABS malfunction.
Recharge the battery.
4-18
When Driving
Instrument Cluster and Display
CX-5_8CA5-EA-11L_Edition3 Page142
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L

Black plate (143,1)
qElectronic Brake Force
Distribution System Warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may illuminate the brake
system warning light and the ABS
warning light on simultaneously. The
problem is likely to be the electronic
brake force distribution system.
WARNING
Do not drive with both the ABS warning
light and brake warning light
illuminated. Have the vehicle towed to
an Authorized Mazda Dealer to have
the brakes inspected as soon as
possible:
Driving when the brake system
warning light and ABS warning light
are illuminated simultaneously is
dangerous.
When both lights are illuminated, the
rear wheels could lock more quickly
in an emergency stop than under
normal circumstances.
qCharging System Warning Light
This warning light illuminates when the
ignition is switched ON and turns off
when the engine is started.
If the warning light illuminates while
driving, it indicates a malfunction of the
alternator or of the charging system.
Drive to the side of the road and park off
the right-of-way. Consult an Authorized
Mazda Dealer.
CAUTION
Do not continue driving when the
charging system warning light is
illuminated because the engine could
stop unexpectedly.
qEngine Oil Pressure Warning Light
This warning light illuminates when the
ignition is switched ON and turns off
when the engine is started.
This warning light indicates low engine
oil pressure.
When Driving
Instrument Cluster and Display
4-19
CX-5_8CA5-EA-11L_Edition3 Page143
Friday, June 22 2012 3:45 PM
Form No.8CA5-EA-11L