ECO mode MAZDA MODEL CX-5 2017 Owner's Manual - RHD (UK, Australia) (in English)

•Severe braking

After rotation, inflate all tyre pressures to
specification (page 9-9) and inspect the
wheel nuts for tightness.
CAUTION
Rotate unidirectional tyres and radial tyres
that have an asymmetrical tread pattern or
studs only from front to rear, not from side
to side. Tyre performance will be reduced if
rotated from side to side.
▼ Replacing a Tyre
WA R N I N G
Always use tyres that are in good
condition:
Driving with worn tyres is dangerous.
Reduced braking, steering, and traction
could result in an accident.
Replace all four tyres at the same time:
Replacing just one ty
re is dangerous. It
could cause poor handling and poor
braking resulting in loss of vehicle control.
Mazda strongly recommends that you
replace all four tyres at the same time.
If a tyre wears evenly, a wear indicator
will appear as a solid band across the
tread.
Replace the tyre w hen this happens.
New tread
Tread wear
indicator
Worn tread
You should replace the tyre before the
band crosses the entire tread.
▼Temporary Spare Tyre*
Inspect the temporary spare tyre at least
monthly to make su
re it is properly
inflated and stored.
NOTE
The temporary spare tyre condition
gradually deteriorates even if it has not
been used.
The temporary spare tyre is easier to
handle because of its construction which is
lighter and smaller than a conventional
tyre. This tyre should be used only for an
emergency and only for a short distance.

Use the temporary spare tyre only until the
conventional tyre is repaired, which
should be as soon as possible.

Refer to Tyre on page 9-9.
CAUTION
 Do not use your temporary spare tyre rim
with a snow tyre or a conventional tyre.
Neither will properly fit and could
damage both tyre and rim.
Maintenance and Care
Owner Maintenance
*Some models.6-45
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

The temporary spare tyre has a tread life
of less than 5,000 km (3,000 miles). The
tread life may be shorter depending on
driving conditions.
 The temporary spare tyre is for limited
use, however, if the tread wear
solid-band indicator appears, replace the
tyre with the same type of temporary
spare (page 6-45).
▼ Replacing a Wheel
WA R N I N G
Always use wheels of the correct size on
your vehicle:
Using a wrong-sized wheel is dangerous.
Braking and handling could be
affected,
leading to loss of control and an accident.
CAUTION
A wrong-sized wheel may adversely affect:
 Tyre fit
 Wheel and bearing life
 Ground clearance
 Snow-chain clearance
 Speedometer calibration
 Headlight aim
 Bumper height
 Tyre Pressure Monitoring System
*
NOTE
•When replacing a wheel, make sure the
new one is the same as the original
factory wheel in diameter, rim width,
and offset (inset/outset).
•For details, contact an expert repairer,
we recommend an Authorised Mazda
Repairer.

Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and flat spots.
Maintenance and Care
Owner Maintenance
6-46*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Brake lights/Tail lights
Rear direction indicator lights
Reverse lights
Rear fog light (Left-hand drive model)*
Rear fog light (Right-hand drive model)*
High-mount brake light
Number plate lights
Overhead lights/Front map lights
Vanity mirror lights*
Rear map lights
Luggage compartment light
WA R N I N G
Never touch the glass portion of a halogen
bulb with your bare hands and always
wear eye protection when handling or
working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurised gas. If one is broken, it will
explode and serious injuries could be
caused by the
flying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the reach
of children:
Playing with a halogen bulb is dangerous.
Serious injuries could be caused by
dropping a halogen bulb or breaking it
some other way.
CAUTION
When removing the lens or lamp unit using
a flathead screwdriver, make sure that the
flathead screwdriver does not contact the
interior terminal. If the flathead screwdriver
contacts the terminal, a short circuit may
occur.
NOTE
•To replace the bulb, contact an expert
repairer, we recommend an Authorised
Mazda Repairer.
•If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
•Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
Maintenance and Care
Owner Maintenance
6-48*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Replacing Exterior Light Bulbs
Headlights, Running lights/Position
lights (Type A), Ru
nning lights (Type
A), Front fog lights*, Side direction
indicator lights, Bra ke lights (Type A),
Brake lights/Tail lights (Type A),
Reverse lights, High-mount brake light
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorised Mazda
Repairer when the replacement is
necessary.
Front direction indicator lights, Position
lights (Type B)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the bonnet. Refer to Bonnet on page 6-22.
3. Turn the socket and bulb assembly anticlockwise and remove it.
4. Disconnect the bulb from the socket. Front direction indicator lights
Position lights
5. Install the new bulb in the reverse
order of the removal procedure.
Running lights (Type B)
*
1. Make sure the ignition is switched off, and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
3. Pull the centre of each plastic retainer
using a flathead screwdriver and
remove the retainers, and then partially
peel back the over fender.
Removal
Installation
Maintenance and Care
Owner Maintenance
*Some models.6-49
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Cavity Protection
Cavities are treated for protection at the
factory, but additional protective treatment
after the vehicle has been put into use will
extend the life of the body.
We recommend that you consult an expert
repairer, we recommend an Authorised
Mazda Repairer concerning this additional
precaution.
▼Bright-Metal Maintenance
•Use tar remover to r
emove road tar and
insects. Never do this with a knife or
similar tool.
•To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high lustre.
•During cold weather or in coastal areas,
cover bright-metal parts with a coating
of wax or preservative heavier than
usual. It would also help to coat them
with noncorrosive p etroleum jelly or
some other protective compound.
CAUTION
Do not use steel wool, abrasive cleaners, or
strong detergents containing highly
alkaline or caustic agents on
chrome-plated or anodised aluminium
parts. This may result in damage to the
protective coating and cause
discolouration or paint deterioration.
▼ Undercoating
This special coating is applied to the
critical parts of the underside to protect
vehicles from damage caused by
chemicals or stones. This coating is liable
to be damaged with time. Check this
coating periodically.

Should repairs be necessary, consult an
expert repairer, we recommend an
Authorised Mazda Repairer. They are well
informed on how repairs should be made.
▼
Aluminium Wheel Maintenance*
A protective coating is provided over the
aluminium wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than mild
detergent. Before using any detergent,
verify the ingredients. Otherwise, the
product could discolour or stain the
aluminium wheels.
NOTE
•Do not use a wire brush or any abrasive
cleaner, polishing compound, or solvent
on aluminium wheels. They may damage
the coating.
•Always use a sponge or soft cloth to
clean the wheels.
Rinse the wheels thoroughly with
lukewarm or cold water. Also, be sure to
clean the wheels after driving on dusty
or salted roads to help prevent
corrosion.
•Avoid washing your vehicle in an
automatic car wash that uses high-speed
or hard brushes.
Maintenance and Care
Appearance Care
*Some models.6-65
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked in a
mild detergent (approx. 5%) diluted
with water.
2. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
3. Before retracting seat belts which have
been pulled out for cleaning, dry them
off thoroughly and make sure there is
no remaining moisture on them.
WA R N I N G
If a seat belt appears frayed or has
abrasions, have it replaced by an
Authorised Mazda Repairer:
If a seat belts is used under such a
condition, it cannot function at its full
capacity which could result in serious injury
or death.
Use a mild detergent to remove soiling
from a seat belt:
If organic solvents are used for cleaning the
seat belts or they become stained or
bleached, there is the possibility of them
becoming weakened and as a result, they
may not function at their full capacity
which could cause serious injury or death.
NOTE
Clean seat belts diligently if they get dirty.
Leaving them uncleaned will make it
difficult to clean them later, and it may
affect the smooth retracting of the seat
belt.
▼Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from
vinyl upholstery
using a leather and vinyl upholstery
cleaner.
▼ Upholstery Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked in a
mild detergent (approx. 5%) diluted
with water.
2. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
▼Leather Upholstery Maintenance*
1. Remove dust and sand using a vacuum
cleaner.
2. Wipe off the soiled area with a soft cloth and a suitable, special cleaner or
a soft cloth soaked in a mild detergent
(about 5%) diluted with water.
3. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
4. Remove moisture with a dry, soft cloth
and allow the leather to further dry in a
well-ventilated, s haded area. If the
leather gets wet such as from rain,
remove the moisture and dry it as soon
as possible.
NOTE
•Because genuine leather is a natural
material, its surface is not uniform and
it may have natural scars, scratches,
and wrinkles.
•To maintain the quality for as long as
possible, periodical maintenance, about
twice a year, is recommended.
Maintenance and Care
Appearance Care
*Some models.6-67
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•If the leather upholstery comes into
contact with any of the following, clean
it immediately.
Leaving it uncleaned could cause
premature wear, mold, or stains.
•Sand or dirt
•Grease or oil, such as hand cream
•Alcohol, such as in cosmetic or hair
dressing items
•If the leather upholstery gets wet,
promptly remove moisture with a dry
cloth. Remaining moisture on the
surface may cause deterioration such as
hardening and shrinkage.
•Exposure to direct sunlight for long
periods may cause deterioration and
shrinkage. When parking the car under
direct sunlight for long periods, shade
the interior using sunshades.
•Do not leave vinyl products on the
leather upholstery for long periods.
They may affect the leather quality and
colouring. If the cabin temperature
becomes hot, the vinyl may deteriorate
and adhere to the genuine leather.
▼Plastic Part Maintenance
CAUTION
Do not use polishing agents.
Depending on the product ingredients,
they could cause discolouration, stains,
cracks or peeling of the coating.
▼ Instrument Panel Top (Soft pad)
Maintenance
Extremely soft material is used for the soft
pad surface. If the so
ft pad surface is
rubbed harshly with a dry cloth, it could
result in the surface being damaged and
leaving white scratch marks.
1. Wipe the soiled area with a soft cloth soaked in a mild detergent (approx.
5%) diluted with water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
▼Active Driving Display
Maintenance*
Windscreen type
The dust-proof sheet has a coating. When
cleaning, do not use a hard or
rough-surface cloth, o
r cleaning detergent.
In addition, if a chemical solvent gets on
the active driving d isplay, wipe it off
immediately. The dust-proof sheet could
be damaged and the surface coating could
be scratched. Use a fine, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning the
dust-proof sheet is recommended.
Auto flip-up type
The combiner and mirror surface have a
special coating. When cleaning it, do not
use a hard cloth, a c loth with a rough
surface, or cleaning detergent. Use a
fine-textured, soft cloth.
If a chemical solvent gets on the combiner
or mirror surface, wipe it off immediately.
Otherwise, they could be damaged and the
surface coating could be scratched.
Maintenance and Care
Appearance Care
6-68*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

3. For vehicles equipped with asub-woofer, loosen the hold-down bolt
and remove the woofe r and spare tyre.
For vehicles not equipped with a
sub-woofer, turn the spare tyre
hold-down bolt anticlockwise and
remove the spare tyre.
Spare tyre hold-down bolt
To secure the spare tyre
Store the spare tyre in the reverse order of
removal. After storing, verify that the
spare tyre is stored securely.
Emergency Flat Tyre
Repair Kit
*
The emergency flat tyre repair kit included
with your Mazda is for a temporary repair
of a slightly damaged flat tyre resulting
from running over nails or similar sharp
objects on the road surface.
Perform the emergency flat tyre repair
without removing the nail or similar sharp
object which punc tured the tyre.
NOTE
Your vehicle is not eq uipped with a spare
tyre. In the event of a flat tyre, use the
emergency flat tyre repair kit to repair the
tyre temporarily. When doing the repair,
refer to the instruct ions included in the
emergency flat tyre repair kit. If an
emergency repair was performed on a flat
tyre using the emergency flat tyre repair
kit, have an expert repairer, we
recommend an Authorised Mazda
Repairer, repair or replace the tyre as
soon as possible.
If Trouble Arises
Flat Tyre
*Some models.7-19
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning
(Red)
High Engine Coolant
Temperature Warning
Indication/Warning
Light The light flashes when the engine coolant temperature is extrem
ely high, and illumi-
nates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine l oad until you can find a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place immedi-
ately and stop the engine.
Refer to Overheating on page 7-37.
CAUTION
Do not drive the vehicle with the high engi ne coolant temperature warning light illumi‐
nated. Otherwise, it could resu lt in damage to the engine.
Power Steering Mal-
function Indication*
The message is displayed if the electric power steering has a m alfunction.
If the message is displayed, stop the vehicle in a safe place a nd do not operate the
steering wheel. There is no probl em if the message in the display turns off after a
while. Contact an expert repairer, we recommend an Authorised M azda Repairer if
the message is displayed continuously.
NOTE
•If the message is displayed , the power steering will not operate normally. In this
case, the steering wheel can still be operate d, however, the operation may feel heavy
compared to normal, or the steerin g wheel could vibrate when turning.
•Repeatedly jerking the steering wheel left and ri ght while the vehicle is stopped or
moving extremely slowly will cause the po wer steering system to go into protective
mode which will make the steering feel heavy, but this does not indicate a problem. If
this occurs, park the vehicle safely and wait several minu tes for the system to return
to normal.
Power Steering Mal- function Indicator
Light
*
The light illuminates/flashes if the electric power steering ha s a malfunction.
If the light illuminates/flashes, stop the vehicle in a safe pl ace and do not operate the
steering wheel. There is no problem if the light turns off afte r a while. Contact an ex-
pert repairer, we recommend an Authorised Mazda Repairer if the light illuminates/
flashes continuously.
NOTE
•If the indicator light illuminates/flashes, the power steering will not operate normal-
ly. In this happens, the steering wheel c an still be operated, however, the operation
may feel heavy compared to normal, or th e steering wheel could vibrate when turn-
ing.
•Repeatedly jerking the steering wheel left and ri ght while the vehicle is stopped or
moving extremely slowly will cause the po wer steering system to go into protective
mode which will make the steering feel heavy, but this does not indicate a problem. If
this occurs, park the vehicle safely and wait several minu tes for the system to return
to normal.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-45
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning
(Red)
Brake Pedal Opera-
tion Demand Warn-
ing Light
*
When only flashing
Flashes if there is the possibilit y of the vehicle not being held in the stopped position by
the AUTOHOLD function, such as on steep slopes. Depress and hol d your foot on the
brake pedal.
When flashing and beep sound is activated at the same time
The warning light flashes and th e beep sound is activated for about five seconds if there is
a problem with the system. If th e warning light flashes and the warning sound is activat-
ed, immediately depress the brak e pedal and stop using the AUTO HOLD function then
contact an expert repairer, we recommend an Authorised Mazda Re pairer.
WARNING
Immediately depress the brake pedal if the warning light flashes and the beep sound is acti‐
vated while using the AUTOHOLD function:
Because the AUTOHOLD function is cancelled forcibly, the vehicle may move unexpectedly
and result in an accident.
Electric Parking
Brake (EPB) Indica-
tion/Indicator Light This warning has the following functions:
Parking brake warning/Indicator light inspection
The light illuminates when the el
ectric parking brake (EPB) is applied with the ignition
switched to START or ON. It turns off when the electric parking brake (EPB) is released.
When the light is turned on
If the light remains turned on e ven if the electric parking brake (EPB) switch is released,
an expert repairer, we recommend an Authorised Mazda Repairer.
When the light is flashing
The light flashes if the electric parking brake (EPB) has a mal function. If the light re-
mains flashing even if the elect ric parking brake (EPB) switch is operated, consult an ex-
pert repairer, we recommend an Au thorised Mazda Repairer as soon as possible.
Check Engine LightIf this light illuminates while d
riving, the vehicle may have a problem. It is important to
note the driving conditions when the light illuminated and consult an expert repairer, we
recommend an Authorised Mazda Repairer.
The check engine light may illuminate in the following cases:
•The engine's electrical system has a problem.•The emission control system has a problem.•The fuel tank level being very low or approaching empty.
If the check engine light remains on, or it flashes continuously , do not drive at high
speeds and consult an expert rep airer, we recommend an Authorised Mazda Repairer as
soon as possible.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-48*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2