light MAZDA MODEL CX-5 2017 Owners Manual (in English)

4–14 0
When Driving
i-ACTIVSENSE
The Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
goes on stand-by status in the following
cases:
  The system cannot detect white (yellow)
lane lines.
   The vehicle speed is less than about
60 km/h (37 mph).
   The ABS/TCS is operating.  The TCS is turned off. (If the TCS is turned off while the
system is operational, a warning beep is
heard and the system goes on standby.)
  The vehicle is making a sharp curve.  The brake pedal is depressed.  The steering wheel is operated abruptly.  The width of a lane is excessively
narrow or wide.

NOTE
   The Lane-keep Assist System (LAS)
& Lane Departure Warning System
(LDWS) does not operate until the
system detects white (yellow) lane lines
on either the left or right.
  When the system detects a white
(yellow) lane line on one side only, the
system will not operate the steering
wheel operation assist and the warning
for the lane line on the side that is not
being detected. The steering wheel
operation assist and the warning is only
for a lane deviation on the side that is
being detected.
  If the driver takes his or her hands off
the steering wheel (not holding the
steering wheel), the warning sound is
activated and an alert is indicated in the
multi-information display or the active
driving display.


Active Driving Display Multi-information Display(Windshield Type)
(Auto Flip-up Type)
 If the steering wheel is held lightly, or depending on the road conditions,
the system may detect that you have
released the steering wheel (not holding
the steering wheel) even if you are
holding it, and display a message in the
multi-information display or the active
driving display.
  The timing at which the lane departure
warning is activated and the steering
wheel operation assist is performed
varies.
CX-5_8FN1-EA-16L_Edition1.indb 1402016/12/12 10:06:14

4–142
When Driving
i-ACTIVSENSE
NOTE
  After the operation, the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) operation may
not operate for a period of 5 seconds
at the most until the lane lines are
detected.
  Under the following conditions, the
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS)
cancels the warning/steering assist
automatically.
  The driver takes his/her hands off the
steering wheel.
 (The Lane-keep Assist System (LAS) & Lane Departure Warning System
(LDWS) is designed to assist the
driver's steering operation and it
will resume operation automatically
when the driver holds the steering
wheel.)
  The TCS OFF switch is pressed to
cancel the TCS.


Steering operation assist OFF (non-
operational)
The steering operation assist for the
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS) can
be changed to non-operational (OFF).
Refer to Setting Change (Personalization
Features) on page 9-11 .
When the steering operation assist has
been changed to non-operational (OFF),
the operation conditions and the display
of the Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
differ. Operate the system as follows:
System operation
Make sure that the Lane-keep Assist
System (LAS) & Lane Departure Warning
System (LDWS) OFF indicator light in the
instrument cluster is turned off. When the
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS) OFF
indicator light turns on, press the switch
and make sure that the indicator light turns
off.


CX-5_8FN1-EA-16L_Edition1.indb 1422016/12/12 10:06:15

4–14 3
When Driving
i-ACTIVSENSE
Drive the vehicle in the center of the
driving lane while the Lane-keep Assist
System (LAS) & Lane Departure Warning
System (LDWS) OFF indicator light in the
instrument cluster is turned off.
The system becomes operational when all
of the following conditions are met.
  The system detects white (yellow) lane
lines on both the right and left sides or
on either side.
   The vehicle speed is about 60 km/h
(37 mph) or faster.
   The vehicle is driven on a straight road
or road with gentle curves.
   The engine is running.
The Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
goes on stand-by status in the following
cases:
  The system cannot detect white (yellow)
lane lines.
   The vehicle speed is less than about
60 km/h (37 mph).
   The vehicle is making a sharp curve.  The vehicle is making a curve at an
inappropriate speed.

NOTE
   The Lane-keep Assist System (LAS)
& Lane Departure Warning System
(LDWS) remains on stand-by until it
detects white (yellow) lines on both the
left and right sides, or on either side.
  When the system detects a white
(yellow) lane line on one side only, the
system will not activate warnings for the
lane line on the side that is not being
detected.
  The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
 Refer to Setting Change (Personalization Features) on page
9-11 .

Vehicle lane line display
When the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) becomes operational while
on standby, the vehicle lane lines are
displayed in the multi-information display.
The system changes to operational status
display when the system detects a white
(yellow) line on either the left or right.
(Stand-by status)


(Operational status)


CX-5_8FN1-EA-16L_Edition1.indb 1432016/12/12 10:06:15

4–14 4
When Driving
i-ACTIVSENSE
Auto cancel
In the following cases, the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) is automatically
canceled, the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) warning indication (amber)
turns on, and an alert is displayed. When
the Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
become operational, the system turns back
on automatically.
  The temperature inside the camera is
high or low.
   The windshield around the camera is
foggy.
   The windshield around the camera is
blocked by an obstruction, causing poor
forward visibility.

(Auto cancel of warnings)
When the following operations are
performed, the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) determines that the driver intends
to make a lane change and the system
operation is canceled automatically. The
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS)
resumes automatically after the operation.
   The steering wheel is operated abruptly.  The brake pedal is depressed.  The accelerator pedal is depressed. (To cancel the automatic sensitivity
cancel function, deselect “Warning
sensitivity” in the personalization
features setting.)
  The turn signal lever is operated.  The vehicle crosses a lane line.
System Canceling
When the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) is turned off, press the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) OFF switch.


The Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
OFF indicator light turns on.


CX-5_8FN1-EA-16L_Edition1.indb 1442016/12/12 10:06:15

4–14 5
When Driving
i-ACTIVSENSE
NOTE
  When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the ignition
is switched OFF with the lane-keep
system operable, the system will be
operable when the ignition is switched
ON the next time.
  In the following cases, the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) is canceled
automatically and the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) OFF indicator
light turns on. Have your vehicle
inspected at an Authorized Mazda
Dealer.
  There is a malfunction in the power
steering.
  There is a malfunction in the TSC.  There is a malfunction in the
Forward Sensing Camera (FSC).


When the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) is turned off, the vehicle lane line
indication in the multi-information display
and the active driving display turn off.
CX-5_8FN1-EA-16L_Edition1.indb 1452016/12/12 10:06:15

4–150
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) system will operate under the foll\
owing conditions.   The engine is running.  The Smart Brake Support/Smart City Brake Support (SBS/SCBS) system war\
ning
indication/warning light (amber) does not illuminate.
  (Rear-end collision warning)  The vehicle speed is about 4 to 80 km/h (2 to 50 mph).  (Brake control (Smart City Brake Support (SCBS) brake))  The vehicle speed is about 4 to 30 km/h (2 to 18 mph).  The Smart City Brake Support (SCBS) system is not turned off.   Under the following conditions, the Smart City Brake Support (SCBS) sy\
stem may not
operate normally:
  The Smart City Brake Support (SCBS) system will not operate if the dri\
ver is
deliberately performing driving operations (accelerator pedal and steer\
ing wheel).
  If there is the possibility of partial contact with a vehicle ahead.  The vehicle is driven on a slippery road surface such as wet roads or icy or snow-
bound roads.
  The braking performance is adversely affected due to cold temperatures or wet brakes.  The vehicle is driven at the same speed as the vehicle ahead.  The accelerator pedal is depressed.  The brake pedal is depressed.  The steering wheel is being operated.  The selector lever is being operated.   In the following cases, the Forward Sensing Camera (FSC) determines that there is a
vehicle ahead and the Smart City Brake Support (SCBS) may operate.
  Objects on the road at the entrance to a curve.  Vehicles passing in the opposite lane while making a curve.  Metal objects, bumps, or protruding objects on the road.  When passing through a toll gate.  When passing through low gates, narrow gates, car washing machines, or tunnels.  If you suddenly come close to a vehicle ahead.  2-wheeled vehicles, pedestrians, animals or standing trees.  Vehicle is driven with some of the tires having signi fi cant wear.

CX-5_8FN1-EA-16L_Edition1.indb 1502016/12/12 10:06:16

4–151
When Driving
i-ACTIVSENSE
Smart City Brake Support (SCBS) Indicator Light (Red)
If the Smart City Brake Support (SCBS) is
operating, the indicator light (red) fl ashes.



Collision Warning
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the multi-information display or the active
driving display.

Multi-information Display
Active Driving Display

NOTE
The operation distance and volume of the
collision warning can be changed. Refer to
Personalization Features on page 9-11 .

Automatic Brake Operation
Display
“Smart City Brake Support Activated” is
indicated in the multi-information display
after the SCBS brakes or the brake assist
(SCBS brake assist) is operated.


NOTE
  The collision warning beep sounds
intermittently while the SCBS brake
or brake assist (SCBS brake assist) is
operating.
  If the vehicle is stopped by the SCBS
operation and the brake pedal is not
depressed, the warning beep sounds
one time after about 2 seconds and the
SCBS brake is automatically released.

CX-5_8FN1-EA-16L_Edition1.indb 1512016/12/12 10:06:16

4–152
When Driving
i-ACTIVSENSE
Stopping the Smart City Brake Support (SCBS) System Operation
The Smart City Brake Support (SCBS)
system can be temporarily deactivated.
Refer to Personalization Features on page
9-11 .
When the Smart City Brake Support
(SCBS) system is turned off, the Smart
City Brake Support (SCBS) OFF indicator
light turns on.



When the engine is restarted, the system
becomes operational.
CX-5_8FN1-EA-16L_Edition1.indb 1522016/12/12 10:06:16

4–154
When Driving
i-ACTIVSENSE
NOTE
  The Smart Brake Support (SBS) system operates when all of the followin\
g conditions are
met:
  The ignition is switched ON.  The Smart Brake Support (SBS) system is on.  The vehicle speed is about 15 km/h or faster (10 mph or faster).  The relative speed between your vehicle and the vehicle ahead is about 15 km/\
h or
faster (10 mph or faster).
  The Dynamic Stability Control (DSC) is not operating.   The Smart Brake Support (SBS) system may not operate under the followi\
ng conditions:   If the vehicle is accelerated rapidly and it comes close to a vehicle ah\
ead.  The vehicle is driven at the same speed as the vehicle ahead.  The accelerator pedal is depressed.  The brake pedal is depressed.  The steering wheel is being operated.  The selector lever is being operated.  The turn signal is being used.  When the vehicle ahead is not equipped with taillights or the taillights\
are turned off.  When warnings and messages, such as a dirty windshield, related to the Forward
Sensing Camera (FSC) are being displayed in the multi-information display.
  Although the objects which activate the system are four-wheeled vehicles, the radar
sensor (front) could detect the following objects, determine them to be an obstru\
ction, and
operate the Smart Brake Support (SBS) system.
  Objects on the road at the entrance to a curve (including guardrails and snow banks).  A vehicle appears in the opposite lane while cornering or rounding a curve.  When crossing a narrow bridge.  When passing under a low gate or through a tunnel or narrow gate.  When entering an underground parking area.  Metal objects, bumps, or protruding objects on the road.  If you suddenly come close to a vehicle ahead.  When driving in areas where there is high grass or forage.  Two-wheeled vehicles such as motorbikes or bicycles.  Pedestrians or non-metallic objects such as standing trees.   When the system operates, the user is noti fi ed by the multi-information display.   The Smart Brake Support (SBS) warning indication (amber) turns on wh\
en the system has
a malfunction.
 Refer to Warning Indication/Warning Lights on page 4-33 .
CX-5_8FN1-EA-16L_Edition1.indb 1542016/12/12 10:06:17

4–155
When Driving
i-ACTIVSENSE
Collision Warning
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated
in the multi-information display and the
active driving display.
Multi-information Display
Active Driving Display

Stopping The Smart Brake Support (SBS) System Operation
The Smart Brake Support (SBS) system
can be temporarily deactivated.
Refer to Personalization Features on page
9-11 .
When the Smart Brake Support (SBS)
system is turned off, the Smart Brake
Support (SBS) OFF indicator light turns
on.


When the engine is restarted, the system
becomes operational.
NOTE
If the Smart Brake Support (SBS) system
operation is turned off, the Smart City
Brake Support (SCBS) system operation is
turned off simultaneously.

CX-5_8FN1-EA-16L_Edition1.indb 1552016/12/12 10:06:17