fuel cap MAZDA MX-5 1994 Workshop Manual

PRE-DELIVERY INSPECTION PRE-DELIVERY INSPECTION PRE-DELIVERY INSPECTION TABLE The following items may be done at any time prior to delivery to your customer. INSPECT and ADJUST, if necessary, the following items to specification: 0 Glass, exterior bright metal and paint for damage 0 Convertible top and detachable hardtop (if equipped) for damage 0 Wheel lug nuts and locks 89-117 N.m (9-1 2 kgf.m, 66-86 ft4bf) 0 All weatherstrips for damage or detachment Operation of hood release and lock Operation of fuel lid 0 Door operation and alignment Headlight aiming INSTALL the following parts: Wheel caps (if equipped) 0 Outside mirror(s) 0 Mast antenna (if equipped) UNDER HOOD-ENGINE OFF INSPECT and ADJUST, if necessary, the following items to specification : Fuel, coolant, and hydraulic lines, fittings, connections, and components for leaks Engine oil level 0 Power steering fluid level (if equipped) Brake and clutch master cylinder fluid level 0 Windshield washer reservoir fluid level 0 Radiator coolant level and specific gravity 0 Tightness of battery terminals pKiq INSTALL the following parts: CHECK operation of the following items: 0 Seat controls (sliding and reclining) 0 Door locks 0 Seat belts and warning system 0 Air bag system using indicator light (Refer to section T) Ignition switch and steering lock 0 Starter interlock switch (clutch pedal) All lights, including warning, and indicator lights 0 Audible warning system 0 Horn, wipers, and washers Audio system 0 Cigarette lighter Power windows (if equipped) 0 Power outside mirrors (if equipped) 0 Heater, defroster, and air conditioner at all mode selections (if equipped) CHECK the following items: Presence of spare fuses 0 Upholstery and interior finish CHECK and ADJUST, if necessary, the following items: 0 Pedal height and free play of brake and clutch pedals I Pedal height mm {in} I Ft: $iy I Clutch pedal {6.89--7.28) (with carpet) Parking brake 7-9 notchesil96 N (20 kgf, 44 Ibf) 0.63.1 (0.024. 12) Brake pedal RUNNING AT OPERATING TEMPERATURE CHECK the following items: 0 Automatic transmission oil level 171-181 (6.73--7.13) (with carpet) I ON HOIST I 4--7 {0.16-0.28} CHECK the following items: 0 Underside fuel, coolant, and hydraulic lines, fittings, con- nections, and components for leaks 4 Tires for cuts or bruises 0 Steering linkage, suspension, exhaust system, and all underside hardware for looseness or damage Manual transmission oil level Differential oil level I ROAD TEST I CHECK the following items: Brake operation Clutch operation 0 Steering control 0 Operation of meters and gauges Squeaks, rattles and unusual noises 0 Overall engine performance Seat belt emergency locking retractors 0 Cruise control system (if equipped) I AFTER ROAD TEST I CHECK for necessary owner information materials, tools and spare tire in vehicle The following items must be done just before the delivery to your customer. 0 Load test battery and charge if necessary -1 Install fuses for accessories Adjust tire pressure to specification Load test fesuk 0 Remove seat and floor mat protective covers (Refer to Door Label) 0 Vacuum and clean interior of vehicle Clean outside of vehicle Inspect installation of option parts with invoice 45UOAX-002 Gartner Banana

Schedule 2 (Unique driving conditions) (AT) Maintenance interval Maintenance item ENGINE Engine oil I R I R I R I R I R I R I R I R I R I R I R I R Engine oil filter Drive belts Number of months or kilometers {miles}, whichever comes first eoilpancapacity: 4.0 L {4.2 US qt, 3.5 Imp qt} Engine oil (Puerto Rico) I I IGNITION SYSTEM Service data and inspection point Months Kilometers (x 1,m) Miles (x 1,000) D-5 Replace every 4,800 km (3,000 miles) or every 3 months I I I I I I I I - - Engine timing belt (California) Spark plugs Page - - Air cleaner element I I FUEL SYSTEM 4 8 5 I F-99 8-1 2 -. . . '21nspect at 96,000 km {60,000 miles}, and again at 144,000 km {90,000 miles) Replace every 168,000 km (1 05,000 miles) - - R*' - 1'1 l Oilfiltercapacity: 0.15 L (0.16 US qt, 0.13 Imp qt} l Cracks or damage l Tension I R 1 Ie2 1 Engine timing belt ~ --- - - l Plug gap: 1 .&I -1 mm (0.040-4.043 in) l Recommended dark ~luas: 8 16 10 D-6 B-6 Replace every 96,000 km (60,000 miles) Idle speed Fuel filter Fuel lines and hoses NGK , BKRGE-11 BKR5E-I 1 12 24 15 IRI I*2 lt2 l Idle speed MT: 800-900 rpm (Neutral) 1 F-76 AT: 75M0 rpm (P range) 16 32 20 I!*'2 1 20 40 25 24 48 30 - Fittings, connections and com~onents for leaks 36 72 45 F-113 F-1 07 Fuel hoses (California) Hose and tube for emission 28 56 35 Cooling system Engine coolant 32 64 40 COOLING SYSTEM Replace every 168,000 km {I 05,000 miles} 1 1*2 48 96 60 40 80 50 I R 44 88 55 l Fittings, connections and components for leaks Fittings and connections F-1 07 - I R l Hoses for cracks or wear l Coolant level - E4 E-5 Gartner Banana

Schedule interval Maintenance ENGINE Number of months or kilometers {miles), whichever comes first I -. Months 5 10 15 20 25 30 35 40 45 50 55 60 Kilometers 8 16 24 32 40 48 56 64 72 80 88 96 - Service data and inspection point 1~1.000~ Page Spark plugs FUEL SYSTEM -- Plug gap: 1 .GI .l mm {0.04M.043 in) l Recommended spark plugs: D-5 D-6 B-6 F-99 8-1 2 IGNITION SYSTEM R I I Engine oil Engine oil filter Drive belts Air cleaner element Engine timing belt 'l R I R I F-76 F-1 1 3 F-107 F-I30 - Idle speed Fuel filter Fuel lines and hoses PCV valve'2 Emission hoses and tubes R I COOLING SYSTEM I Cooling system Engine coolant R I R I I E4 E-5 E4 I R I R I R I R I*z I l Hoses for cracks or wear l Leaks - Level and strength I R RR I R R R I I R I OilPancapacity: 4.0 L (4.2 US qt, 3.5 Imp qt) 0 Oil filter capacity: 0.15L(0.16USqt,0.13Impqt) 'Cracksordamage 0 Tension - - R I I I I I R I l ldle speed MT: 800-900 rpm (Neutral) AT 750-850 rpm (P range) - l Fittings, connections and components for leaks Operation Fittings and connections I I R I I I I I I I I I R I Gartner Banana

F OUTLINE SPECIFICATIONS Item Specification I Throttle body Throat diameter mm {in) I 55 I2.2) Idle speed rpm Ignition timing BTDC 800-900 (850 -+ 50)[MIb, 750-850 (800 + 50)[ATJe 9"-11" (10" k 1 ")* ~ut~~~ressure kPa {kgf/cm2, psi) 1 46-57 14.9--6.7,6%95) Fuel filter Fuel pump TY pe -- m&e regulator Impeller (in-tank) Low-pressure side Hi~h-pressure side Nylon element Paper element Fuel injector TY pe I High-ohmic Type Regulating pressure kPa {kgf/cm2, psi) Diaphragm 26S314 (2.7--3.2,38--46) ldle Air Control Valve Solenoid resistance n 1 10.7-1 2.3 (at 20°C {M°F)) Type of drive Resistance R Voltage 12-1 6 (at 20°C {68"F)) I Solenoid resistance 1 23-27 (at 20°C (68"FJ) I -- brankshaft position sensor d Air valve Opening temperature I Resistance Below 40°C {I 04°F) TY pe Capacity L {US gal, Imp gal) I 48 {12.7, 10.5) Air cleaner housing Purae solenoid valve Hall effect Engine coolant temperature sensor Free play mm (in) I 1-3 {0.0394.118) Fuel Specification 1 Unleaded regular (RON 87 or higher) Element type I I -. I *... With System Selector (49 B019 9AO) test switch at SELF TEST. 35UOFX-004 Oil permeated Accelerator cable Gartner Banana

F FUEL SYSTEM FUEL PUMP Inspection Fuel pump operation 1. Connect the data link connector terminals F/P and GND , with a jumper wire. 2. Remove the fuel filler cap. 3. Turn the ignition switch ON. 4. Listen for operational sound of the fuel pump at the filler inlet. 5. Install the fuel filler cap. 6. If no sound was heard, measure the voltage between the fuel pump connector wire to ground. Voltage: Battery positive voltage 7. If not correct, check the fuel pump relay and its circuits. (Refer to page F-116.) 8. If the voltage is normal, check for continuity between fuel pump connector (6) and a ground. 9. If there is continuity, replace the fuel pump. 10. If no continuity, repair the ground circuit. Hold pressure Perform this inspection if the fuel pressure hold inspec- tion is not as specified. (Refer to page F-109.) Warning Fuel line spills and leaks can be dangerous. Fuel can ignite and cause serious injuries or death and can damage the vehicle. Fuel can also irritate skin and eyes. To prevent this from happening, release the fuel pressure according to "Fuel Line Safety Procedures" on page F-108. 1. Disconnect the negative battery terminal. 2. Connect a fuel pressure gauge to the fuel main pipe and plug the outlet of the fuel pressure gauge as shown. (Install clamps as shown.) 3. Connect the negative battery terminal. Gartner Banana

FUEL SYSTEM -- FUEL TANK GAUGE SENDER UNIT SIDE FUEL PUMP 45UOFX-256 1. Remove the rear package trim. 2. Remove the service hole cover. 3. Remove the fuel pump cover. 4. Disconnect the fuel pump connector. 5. Disconnect the fuel hoses. 6. Remove the fuel pump and fuel tank gauge sender unit assembly. 7. Remove the fuel pump. 8. Install in the reverse order of removal, referring to Instal- lation note. Installation note O-ring set 1. Use a new O-ring set. (O-ring, cap, and spacer) 2. Apply oil or fuel to the O-ring set before installing. 3. To confirm sealing of the O-ring, after assembling the fuel pump and fuel tank gauge sender unit, blow air through the fuel main pipe and verify that no air flows. If air flows the check ball may be stuck. Shake the fuel pump 2 or 3 times and recheck. Fuel pump After installing the fuel pump to the bracket, pull down the fuel pump down so that it is tight against the bracket. Gartner Banana

TD TECHNICAL DATA Idle speed rpm 1 800-900 (850 2 50) [MT]', 750-850 (800 f 50) [ATJ' lanition timina BTDC I 9"-11' (10' f 1")' u' F. FUEL AND EMISSION CONTROL SYSTEMS - Engine ltem Item 1 Throat diameter mm {in) 1 55 (2.2) 1 Antifreeze solution BP DOHC Specification 1 Throttle body Fuel pump TY pe I Impeller (in-tank) Coolant protection Above -1 6°C (3°F) Above -26°C (-15°F) Above -40°C {-40°n Tv~e -. Output pressure kPa (kgf/cm2, psi) I 294-437 {3.0--6.5,43--92) Fuel filter Specific gravity at 20°C {WF) 1.054 1.066 1.078 Volume percentage % Horizontal draft Water 65 55 45 -. . - Regulating pressure kPa {kgf/cm2, psi) I 280-289 I2.85--2.95, 40.141.9) Fuel iniector Coolant 35 45 55 TY pe IAC valve Solenoid resistance n 1 10.7-1 2.3 (at 20°C (68°F)) Low-pressure side TYP~ Type of drive Resistance n Purge solenoid valve Solenoid resistance n 1 23-27 (at 20°C (68°F)) I Nylon element Pressure regulator TY pe High-ohmic Voltage 13.8 (at 20°C (68"FI) Engine coolant temperature sensor 7 20°C {68"F) I 2.21 -2.69 Resistance kn I 80°C (1 76OF} I 0.287-0.349 High-pressure side Diaphragm i/ Crankshaft position sensor Air valve Openin~l temperature OC {OF) I Below 45 (1 131 Paper element Twe 1 Fuel tank I Hall effect . . . . . . . Capacity L {US gal, Imp gal) I 48 {12.7, 10.5) Air cleaner housing Element type Free play mm (in) I 1-3 {0.039--0.118) I Fuel Oil permeated Specification Accelerator cable Unleaded regular (RON 87 or higher) J +....with system selector (49 B019 9AO) test switch at SELF TEST Gartner Banana

CONSTRUCTION No. @ I Rear deck panel @ @ - - 1 8 1 Quarter panel Part Name @ I Rear deck member Trunk lid Rear end panel I @ 1 Light housing No. Part Name @ Q @ I Tunnel gusset Seal plate Splash protector @ @ I @ I Rear fender panel Bulkhead panel Floor side panel Floor center pan 0 I Crossmember No. 4 @ @ I @ I Door body @ Q Rear fender gusset Rear fender rain rail Fuel filler lid Parking bracket Crossmember No. 3 8 1 Floor side plate @ @ I @ / Side sill, inner B @ @ I ~ut plate Rear fender, lower Trunk board bracket Tank floor pan assy Trunk floor assy 1 8 1 Side sill reinforcement Q @ 0 I Rear side frame Striker reinforcement Side sill, inner C I I I 1 8 ( Cowl side panel @ @ I Closing bracket I @ I Hinge pillar Floor side panel @ @ 8 1 Battery clamp bracket I @ I Side sill, inner Side sill, outer Bumper bracket Cap bracket @ I Corner junction 1 8 1 Front header, Q @ @ @ Side sill gusset Hinge pillar, outer Side panel, inner Wheel inner house @ @ @ Beltline reinforcement Front pillar, outer Front pillar, inner @ Front header, upper Gartner Banana

ALPHABETICAL INDEX *%* ENGLISH *** CASE,T/MISSlON------------ CASE'A' , LLOWER UNIT- ----- CASE'A',COOLING UNIT----- CASE'A1 ,HEATER UNIT------ CASEIB' ,BLOWER UNLT------ CASE'B' ,COOLING UNIT----- CASE'B9,HEATER UNIT------ CASE'OUT',ASHTRAY-------- CASING,DIFFERENTIAL------ CASING,HYDRAULIC UNIT---- CASING,STOPPER----------- CATALYST ,THREE WAY------- CEILING,TOP-----.--------- CHANNEL( L) DIVISION-DOOR- CHANNEL(R)lDIVISION-DOOR- CHECKER,DOOR------------- CLAMP---------.-..--------- CLAMP,BATTERY------------ CLAMP,HOSE--------------- 1-L11 DRUM,CLUTCH-------------- 1-N8 DRUM,CONNECTING---------- 1 -H9 DRUM,DIRECT------------.- 1-F9 DRUMIREAR CLUTCH------ -- 1-C9 DUCT(L)---------------..-- 2-DB DUCT(L1 ,SIDE DEMI .-- .---- DUCT(R)----..------------- 2-C8 2-DB DUCT(R1,SIDE DEMT,------- DUCT,AIR- ---- ------------ 2-C8 DUCT,CENTER-------------- 2-Cll 2-C8 DUCTIFRESII AIR----------- 1-14 CLIP,WEATHLRSTRIP-OUTER-- 2-El1 CLIPtA',SPEEDOMETER CABLL 2-F7 CLIPIA',WEATHERSTRIP-OUT- 2-El1 CLIPIB',WIRE-BONNET------ 2-E5 CLGTH,REPAIR-TOP-------..- 2-Dli CLAMt3,HOSE-A 1 .P. /A. CLNR CLAMP,WATER HOSE--------- ELEMENTIAIR CLEANER------ 1-J4 EMBLEM,CAP-WIiE€I.--------- 1-Ll;? END,CONTROL LEVtR-------- 1 -K6 ENDlS/ROD<1ST82ND)------- 1-J6 ENl)rS/ROD(3RDB4TH;------- 1-J6 ENG:SHIFf ROD(O/TOI'&REV.) 1-K6 ENGINE,PARTIAL----------- ENGINE,SHORT------------.- 1-D3 ESCUTCHEON--------------- 1-D3 EVAPORATOR--------------- 2-ti9 2-Mll EYE BOLT K?T,31. GEAR---- 1-M12 2-116 2-L12 2-N5 COVER,5OIE-CC1----------- 2-Ki COVER,HOLE-ANTENNA------- 2-El4 COVER,HOLE-LIFT GATE----- 2-Dl0 COVER,INNER HANDLE----.--- 2-M9 COVER,INTERIOR MIRRORm--- 2-F16 COVER,JOINT-LOWER-------- 1-112 COVER,JOINT-UPPER-------- 1-112 COVER,LEVER-OPENER------- 2-L7 COVER,MAIN FUSE BLOCK---- 2- I1 4 COVER,OIL PUMP----------- COVER,REAR--------------- 1-N4 1-J3 1-K12 COVEK,RE&R-ALTERNATOR---- 1-C7 CQVER,RELAy------------..- 2-H1! COVER,ROD---------------- 1-1.6 COVER,SELECT LEVER------- 1-616 COVERISERVICE HOLE------- Z-F5 COVER,SERVO-------------- COVER,SIDE--------------- 1-N7 2-K7 COVERISPARE TIRE--------- 2-Cl6 COVER,l'HERHO------------- 1-D5 CQVER,THERMOSTAT--------- 1-D5 COVER,TIMING EELT-C. ----- 1-13 GASKET------------------- 1-C5 1-C15 1 -F3 1-H7 1-J14 1-L4 1 - L 14 1-N7 2- ~4 GASKET 8 SEAL KIT-------- 1-M9 GASKET KIT,COMPRESSOR---- 2-K11 GASKET SET ,CYL HEAD----- i -D3 GASKET SETIENGINE-------- 1-DY GASKET(C1 ,TIMING BELTCL) - 1-13 GASKEl'(INN),TIHIHG BELTCL 1-13 BASKET(L)---------------- GASKET,CAP--------------- 1-13 1-114 GASKETICONPRESSOR-------- 2-K11 GASKET,CONVERTER--------- !-Dl4 G0.SKET ,COVER PLATE------- 1-K6 GASKET,CYl.INDER WEAD----- 1-F3 GASKET,DRAIN PLUG-------- 1-li14 GASKETIDRUM SUPPORT- ----- 1 - D8 CASKET.E.G.R. VALVE------ 1-L4 CORD NO.1,HI.TENSION----- 1 -M6 CORD NO.2.HI.TENSION----- 1 -M6 CORD NO.~;HI.TENSION----- 1 -M6 CORD NU.4,HI.TENSION----- 1 -M6 CORD SET,HI.TENSION------ 1 -M6 CORa,EARTH--------------- 2-c14 2-Nl:! CORE,HEATER Ub!IT--------- 2-Dl1 COTTER,VALVE-IN.--------- 1 -N3 COUPLERISOLENOID VALVE--- 1-E0 COVER-------------------- l-Cl6 2-C6 COVER NO.l,ADJ-FRT------- 2-66 COVER NO.2,ADJ-FRT-a+----- 2-60 COVER N0.3.ADJ-FRT------- 2. SC COVER(C),SENSOK---------- 2-H9 COVER(L),BELT LINE------- 2-Kli COVER(L).BRACE BAR------- 2-C6 COVER,UNDER-------------- 2-C6 COVER,VALVE BODY--------- 1-10 COVER,WASHER TANK-------- 2-F1E COVER,WHEEL CORE--------- 1-Hli COVER, WIPER ARM-FRONT--- - 2-H15 COVER'L1,HYDRAULIC UNIT-- 1-Ml5 COWLING,RADIATOR--------- CRANKSHAFT--.. -- ------ ---- 1-E5 1 -K3 CUPISECONDARY------------ 1-H15 CUSHION(L),FRT SEAT------ 2-N8 CUSHIOW(R),FRT SEAT------ 2-K8 CUSHION,LID HINGE-------- 2-H4 CUSHION.RUBBER----------- 2-17 2-Ll CYL.,CLUTCH MASTER------- I -El4 CYL.,CLUTCH RELEASE------ 1-El4 CYL,,TAHDEM MASTER------- 1-F15 1-61 5 1-H15 /~ASKET;EX.MANIFOLD------- 1-E4 GASKET,EXH.PIPE-CONVERTER 1-Dl4 GASKET,EXTENSION--------- 1-C8 GASKET,FILLER PIPE------- 1-H14 GASKET ,FRONT COVER--- .--- I-C6 GASKET,HEAD COVER-------- 1-fi3 GASKET,IN.MANIFOl.D------- 1-D4 GASKET.LICENSE LAMP------ 2-H4 COVER( L) ;DECK LOCK------- 2- Jli COVER(I.),DRAIN-SOFT TOP-- 2-Hli COVER(L),DUST------------ 1-El2 1-Fl? COVER(L),HINGE----------- 2-D9 COVER( L) ,HOLE----------- - 2-Nl! COVER(L),KNUCKLE--------- 2-NB COVER(L).SEAT BACK------- 2-N8 - ... CLIP SET,DRlVE SI!AFT----- 1-DlI CLIP(L1 ,FORM PLATt .------ 2-El2 CLIP(R),FORM PLATE------- CLIP,CABiE--------------- 2-El2 1-Dl6 CLIP ,ENGINE HARNESS------ 2-N141 CLIP,FLEXIBLE Hi3SE------- 1-C16' l-~ld I-Ml5 2-1314 FASTENER SET ,TOP CLOTH--- 2- Dl2 FASTENER,BONNET RELEASE-- 2-KG FASTENER,DOOR TRIM------- 2-rl0 2-#7 GASKET,OIL PUMP---------- 1- J7 GASKET ,OIL STRAINER-- ---- 1-C5 1-rJ4 GASKET.RR.COH0.---------- 2-F4 1-1jsl CQv~~(~);S~~so~-l-------- 2-H9 I I-K~SI COVER( L) ,SENSOR-AIR BAG-- 2-H9 CLIP,HAHNESS------------- 2-E15: COVER(R),REL'I LINE------- FKl4 2-G13! COVER(R),BRACE BAR------- 2-C6 , 2-M14' CUVER(W),DECK LOCK------- 2-1121 2-N14( COVERIR) ,DRAIN-SOFT TOP-- 2-HIZi CLlP,HARNESS-HAND BRAKE-- 2-M7 I COVERCR) ,DUST.----------- 1-E13i CLlP,HEATER COtITKOL--- - -- 2-Elli 1-F131 CLIP, HOSE- SUB T.8 VATFR H 1 -F5 i COVER(R) ,HINGE- ---------- 2-C9 ! CLIP,OIL FJPE-------. ---- 1-L7 I CLIP ,PIPE--- -..- ---------. 2-N8 j I-El6: COVER(R),HOLE------------ Z-N1S1 x-~I(+ COVER(RI,KNUCKLE--------- 2-18 I 1-Fl6, COVER(R) ,SEAT BACK------- 2-K8 I FASTEHERILIFT GATE TRIM-- 2-F14 FASTENERBRAIN RAIL-REAR-- %-Eli FASTEHER; RAIN FASTENER. REAR 1 SIDE TUXN- - .SPRANG CAP- FASTEYER,SEEL------------ 1- J3 1-K4 FASTENER, STOP LAMP-HI . --- II D f FEEDER-ANTENNA- - - - - -- - - - - 2-F14j GASKET~VAC POWER ASSIST- !-El5 I )t s FILTER ,AIR--------..------ 2 - N 12 1-G15 FILTER, FUEL- - ..- - - - - - ----.. ~%*t*~x*rfi**tf%%w 1-F4 1 SASK6T.W.PUMP INLET------ 1-D5 I FII.TEP,FUEL PUMP--------- 1-H14 GASKET,WATER PUMP------ - 1-05 IlAl~,FRONT-WIND.---------- 2-~111 FINISHEPIWEAR------.----- 2-i4 GASKET,WINDOW REGULATOR-- 2-C10 . . . . . . . -. . . . . . -- .. - -- ------- L.- -.- --- -.-- CAT. AUNA04-03 F.-002 Gartner Banana

ALPHABETICAL INDEX *** ENGLISH **E SPRING,SHIFT ROD ENS----- SPRING,SHIFT ROD-REVERSE- SPRING,SYNCHRO. KEY------ SPRlNG.SYNCHR0 .KEY------- I-LB SPRING,3-4 SHIFT--------- 1-K8 STABILIZER,FRONT--------- 1-K13 STABXLIZER,RR------------ STARTER..----------------- 1-El2 1-E7 STATOR ---.-.---- - 1-67 1 -C7 STAY(L1,RR. RUMPER------- 2-H3 STAYCR) ,RR. BUMPER------- 2-H3 STA~,B~NNET-------------- 2-K4 STAY,LOCK-BONNET--------- 2-N4 STAY,MANIFOLD------------ 1-D4 S~EM,PJSTON-------------- 1-N7 STEH,PISTON BAND--------- STOPPER SET-------------- 1-E8 1-E7 1-67 STOPPER,RUMP------------- 1 -C12 1-H13 STOPPERICONSOLE LID------ 2-N7 STOPPER,FILLER LID------- 1-K14 STOPPEK,GLASS------------ 2-L'3 STOPPERILINK-HOOD-------- 2-Dl2 STOPPERISOFT TOP--------- 2-L12 STOPPER,LIPPEP-BACK WINDO 2-El2 STRAINER,INNER----------- 1 -K8 STRAINER,OJL-------- ----- 1-18 1-J8 1-144 STRAP ,ALTERNATOR--------- 1 -M6 STRIKER-- ------ ----- ---- - 2-C10 2- J7 STRIKER(L),LOCK-TOP------ 2- J12 STRIKEK(R),LOCK-TOP------ 2- J1.2 STRIKER,LID---..---------- 2-M4 STRUT,BAND--------------- 1 -n7 STUD--------------------- 1-E3 1 -E4 STUD,EX. MANIFOLD------- -- 1-E3 STUD,HEX-HYD. UHJT------- 1 -MI5 SUN VISOR(L)-----------..- 2-F16 SUN v~so~(~)------------- 2-Fl6 §UPPORT(L),MOUNTING------ 1-F11 1-613 SUPPOHT(R),MOUNTING------ 1-F11 1-G13 SUPPORT,C€NTER----------- 1 -G9 SUPPORT,DRUH------------- 1 -D8 SUPPORT.OIL PIPE--------- 1-L7 SUPPURTER,ACTUATOR------- 1-K9 SUPPORTER,FORK----------- 1-C6 ..- - . - - - - --.- - - CAT. AUNA04 - 03 2-~12 SWITCH(R),CLUSTER-------- 2-El3 SWITCH,BACK UP LAMP------ 2-N12 SWITCH,Cl.UTCH------------ 1-L14 SWITCH ,CLUTCH CUT-------- 1 -HI4 SWITCHICOMBINATION------- SWJTCH,DOOR-------------- 2.-F13 2-113 SWITCHIFAN-HEATER CONTROL 2-Ell SWITCH,IGNITION---------- 2-C3 SWITCH,INHIBITOR--------- 2-C13 SWITCH,LEVEL-WASHER TANK- 2-El5 SWITCH,MAIN-------------- 2-El3 SWITCHIOIL PRESSURE------ 2-N12 SWITCH,OVER DRIVE CONTROL 1-616 SWITCH,PARKING LAMPe----- 1-Dl6 SWITCH,POWER WINDOW------ 2-N7 SWITCH,RMT.MIRROR--------- 2-El3 SWITCH,RR.DEF.----------- 2-El3 SWITCH,STOP-LAMP--------- 1-Dl5 1-M14 1-N14 2-Fi5 TANK,WASHEH-FRONT-------- 2-C15 2-El5 TAPE,EDGE PROTECTOR-CTR-- Z-K12 TAPE,PROTECTOR-STOPPER--- 2-El0 TAPE,SEAL-RAIN RAIL------ 2-El2 TENSIONER,T.BELT--------- 1 -C4 TERMINAL SET------------- 1-D7 THERMOSTAT SET----------- 1 -D5 THERMOSTAT,COOLIHG UNIT-- 2-Mll TIMER & BUZZER----------- TIRE ---..- ----------..----- 2-013 TOOL SET----------------- 1-L13 2-Dl6 TRA~,ASH----------------- 2-D7 TRAY,BATTER~--------.----- 1-17 TRAYIREAR PACKAGE-------- 2-L15 TRIMIL),'A'PILLAR-------- 2-K15 TRIM(L1,DOOR------------- 2-61 0 2-HlO TRIM(L1,FRONT SIDE------- 2-l.15 TRIMCL) ,UUARTER---------- 2-116 TRIM(L),SEAT BACK-------- 2-CY 2-D9 TRIM(L1,SEAT CUSHION----- 2-NO TRIM(L),TRUNK SIDE------- 2-M15 TRIM(R),'A'PILLAR-------- 2-K15 TRIM(R),DOOR------------- 2-F10 2-61 0 TRIM(R),FRONT SIDE------- 2-L15 TRIM(R),OUARTER---------- 2-116 TRIMCR) ,SEAT BACK----.---- 2-M8 TRIM(K),SEAT CUSHION----- 2-KO TKIH,FRONT HEADER------ -- 2-K15 TRIM,TRUNK END--------- -- 2-MIS TUBE,FILLER---------TuBE,FILLER------------..---TuBE,FILLER------------..-TuBE,FILLER------------..-- I -D8 TUBE,HEAD LAMP----------- 2-C4 TUBEIOIL FILTER-UPPER-- -- 1-00 TU3E,SILJCOq------------- 1-J3 TUBE,VACUUH-------------- 1 -F4 1-17 1-L4 TUNER 8 DEC.:,COHB.------- 2-M13 VALVE,CONTROL------------ 1-00 VALVE,CONTROL BACK UP---- VALVE,E,G.R. ..----------a- 1 -K8 1-L4 VALVE,EXHAUST------------ 1-N3 VALVE,EXPAHSION---------- 2-Ml VALVE,FUEL VAPOR.-------- 1-11 VALVE,IDLE AIR CONTPOL--- 1-K4 VALVE,INLET-.------------- VALVE,MANUAL----------..-- 1-N3 1-00 VAL,VE,MODIFIER----------- 1 .H8 VALVE,NON RETURN--------- 1-11 VALVE,OIL JET------------ 1-H3 VALVE,ONE WAY------------ 1-E8 1-K8 VALVEjORIFICE CHECK------ VALVE,P.B.---------------- 1-Ha 1-11 1-Ki VALVE,P.C.V.------------- 1 -F3 VALVE,REDUCING----------- 1 -18 VALVE,REGULATOR---------- 1 -GB VALVE,RELIEF------..------ 2-Kl VALVE,SHIFT 3-4---------- 1-U8 VALVEISOLENOID----------- 1-L4 2-Hl VALVE,SOLENOID N01------- 1-K8 VALVE,ST. GEAR----------- 1-N1 YALVE,THREE WAY---------- 1-L4 2-Nl VALVE,THROTTLE----------- 1-Ha VALVE,THROTTLE BACK-UP--- 1-H8 VALVE,l-2 REDUCING------- 1-18 VALVE,l-2 SHIFT---------- 1-G8 VALVE,2-3 SHIFT---------- 1 -G8 VALVE,3-4 SHIFT-COAST---- 1 -K8 WASHER------------------- 1 -F9 1-H1 1-H1 1-11 1-K1 1-L1 1 -Ml 2- J1 2-L3 WASHER SET--------------- 2-Ll 1-E7 WASHER,DISHED------------ 1 -KB WASHER,FASTEN€k-RAIN PAIL 2-El WASHER,FRONT CLUTCH------ 1-E9 WASHER,HOOKmA'----------- 2-1.1 WASHER,HOOK'A'LIB'------- 2-K1 WASHERIHYD. UNIT--------- 1-Hl WASHER,LID OPENER-------- 1-K14 WASHER,LOCK-PUMP FILTER-- 1-H14 WASHERIPLAIN------------- 1-C8 1-H9 1-J7 1-N7 WASHERIPLAIN CYL. HEAD--- 1-E3 WASHER,PLAIN-FRAME------- 1-C14 WASHERISETTING----------- 2-J9 MASHER,STOP-------------- 1-F12 WASHER,THRUST-----------• 1-F6 1-Gh 1-16 WASHER,THRUST LOCK-OVER T 1-H6 1-16 WASHER,THRUST-REVERSE IDL 1-H6 WASHEW,TOOTHED----------- 2- J15 WASHER WAVE-CHANGE C0NT.C 1-L6 WASHER. A' DECK LOCK------ 2-112 WASHERIB',DECK LOCK------ 2- J12 WEATHERSTRIP N0.1-------- 2-El0 WEATHERSTRIP N0.2-------- ?-El0 WEATHERSTRIP(L1---------- 2-K9 WEATHERSTRIP(L1,DOOR----- 2-K9 2-L9 UEATHERSTRIP(L),OUT/---- 2-El0 WEATHERSTRIP(R)---------- 2-K9 WEATHERSTRIP(R),DOOR------ 2-K9 WEATHERSTRIPCR) ,OUT, ------ 2-El0 WEATHERSTRIP, BONNET-REAii- 2-K4 WEATHERSTRIP,D.TOP-REAR-- 2-K12 WEATHEWSTRIP,LID---me---- 2 -H4 WEDGE,DOOR-FRONT--------- 2-Dl0 WEIGHT,DISC WHEEL-ALUMI-- :-HI3 WEIGHTIDISC WHEEL-STEEL-- 1-L:3 1-M13 WIRING~INJECTOR---------- 2-114 WREHCH,HUB NUT----------- 2-Dl6 WRENCHIWHEEL CAP--------- 2-Dl6 WTHSTP NO.l(L),LINK------ 2-Gl2 WTHST? tiO.l(R) ,LINK------ 2-612 WTHSTP H0.2CL) ,LINK------ 2-01 2 WTHSTP NO.?(R),LINK------ 2-812 WTHSTP NU.3(L),LINK------ 2-612 WTHSTP H0.3(K),LINK------ 2-612 WTHST?(L),CAB SIDE------- 2-H12 WTHFiP(L),ROOF PANEL----- 2-K12 WTH'TP(R),CAB SIDE------- 2-H12 WT'iSTP(R),ROOF PANEL----- 2-K12 G'IHSTP,FROHT HEADER------ 2-612 YOKE------------.-------- 1 -E7 1-67 YOKE SETISUPPORT-ST. GEAR 1-L12 YOKE,DTFFEREHTIAL-------- 1-Jl1 Gartner Banana