lock MERCEDES-BENZ GLC 2019 Workshop Manual

XInsert new bulb into bulb holderD.
XInsert bulb holderDinto groove with lug attop.
XPush bulb holderDdown until it engagesaudibly.
XPress on housing coverCand turn it clock-wise.
Turn signals
XRemove the cover in the front wheel housing(Ypage 115).
XTurn bulb holderCcounter-clockwise usingthe grip under the headlamp casing andremove it downwards with bulb.
XTurn defective bulb counter-clockwise andremove it from bulb holderC.
XInsert new bulb into bulb holderC.
XInsert bulb holderC, turn it clockwise andlock.
XReplace the cover in the front wheel housing(Ypage 115).
Removing and installing the cover in the
front wheel housing
You must remove the cover of the front wheelhousing before you can change the front turnsignal lamp.
XTo remove:switch off the lights.
XTurn the front wheels inwards.
XTurn rotary knobC180° outwards until itstops using a suitable object.CoverDis released.
XFold coverDup.
XTo install:insert coverDinto the left, rightand two lower catches.
XTurn rotary knobC180° inwards until itstops using a suitable object.CoverDis locked.
Windshield wipers
Switching the windshield wipers
on/off
!Do not operate the windshield wipers whenthe windshield is dry, as this could damagethe wiper blades. Moreover, dust that has col-lected on the windshield can scratch the glassif wiping takes place when the windshield isdry.
If it is necessary to switch on the windshieldwipers in dry weather conditions, always usewasher fluid when operating the windshieldwipers.
!If the windshield wipers leave smears on thewindshield after the vehicle has been washedin an automatic car wash, wax or other resi-dues may be the reason for this. Clean thewindshield using washer fluid after washingthe vehicle in an automatic car wash.
!Intermittent wiping with rain sensor: due tooptical influences and the windshield becom-ing dirty in dry weather conditions, the wind-shield wipers may be activated inadvertently.This could then damage the windshield wiperblades or scratch the windshield.
Windshield wipers115
Lights and windshield wipers
Z

Problems with the windshield wipers
ProblemPossible causes/consequences andPPSolutions
The windshield wipersare jammed.Leaves or snow, for example, are obstructing windshield wiper move-ment. The wiper motor has been deactivated.
XSwitch off the engine.
XRemove the SmartKey from the ignition lock.
or, on vehicles with KEYLESS-GO or KEYLESS‑GO start function:
XOpen the driver's door.The vehicle electronics are now in position

Vehicles with 3-zone automatic climate control:use the "Residual heat" function if you want toheat or ventilate the vehicle interior when theignition is switched off. The residual heat func-tion can only be activated or deactivated withthe ignition switched off. The residual heat func-tion is deactivated when the ignition is switchedon.
DYNAMIC SELECT switch (except
Mercedes-AMG GLC 63 4MATIC/
GLC 63 S 4MATIC)
You can choose between various drive programswith the DYNAMIC SELECT switch(Ypage 139).
If you have selected drive programE:
Rwhen heating, the electrical heater booster isdeactivated and heat output is reduced as aresult
Rthe rear window defroster running time isreduced
If you have selected drive programC,SorS+,the current climate settings are maintained.
ECO start/stop function
During automatic engine switch-off, the climatecontrol system only operates at a reduced capa-city. If you require the full climate control output,you can switch off the ECO start/stop functionby pressing the ECO button (Ypage 137).
Operating the climate control sys-
tems
Activating/deactivating climate con-
trol
General notes
When the climate control is switched off, the airsupply and air circulation are also switched off.The windows could fog up. Therefore, switch offclimate control only briefly
Switch on climate control primarily using theXrocker switch (Ypage 123).
Activating/deactivating
XTurn the SmartKey to positionHin the igni-tion lock (Ypage 131).
XTo switch on:set the airflow to level1orhigher using theHrocker switch.
XTo switch off:set the airflow to level0usingtheHrocker switch.
i3-zone automatic climate control: when cli-mate control is switched off, "OFF" appears inthe rear-compartment display.
Switching cooling with air dehumidification on/off
General notes
If you deactivate the "Cooling with air-dehumidification" function, the air inside the vehicle will notbe cooled. The air inside the vehicle will also not be dehumidified. The windows can fog up morequickly. Therefore, only deactivate the "Cooling with air-dehumidification" function briefly.
The "Cooling with air dehumidification" function is only available when the engine is running. The airinside the vehicle is cooled and dehumidified according to the temperature selected.
Condensation may drip from the underside of the vehicle when it is in cooling mode. This is normaland not a sign that there is a malfunction.
Activating/deactivating
XPress theZrocker switch up or down.The indicator lamp above the rocker switch lights up or goes out.
122Operating the climate control systems
Climate control

Problems with the "Cooling with air dehumidification" function
ProblemPossible causes/consequences andPPSolutions
The indicator lamp abovetheZrocker switchremains off. The coolingwith air dehumidificationfunction cannot be acti-vated via the multimediasystem any longer(Ypage 273).
Cooling with air dehumidification has been deactivated due to a mal-function.
XVisit a qualified specialist workshop.
Setting climate control to automatic
General notes
In automatic mode, the set temperature is main-tained automatically at a constant level. Thesystem automatically regulates the temperatureof the dispensed air, the airflow and the air dis-tribution.
During automatic controlling, the "Cooling withair dehumidification" function is activated.
Automatic control
XTurn the SmartKey to positionHin the igni-tion lock (Ypage 131).
XTo activate:press theXrocker switch upor down.The indicator lamp above theXrockerswitch lights up.
XSet the desired temperature using the

Setting the temperature in the front com-
partment using the front control panel
XTurn the SmartKey to positionHin the igni-tion lock (Ypage 131).
XTo increase or reduce:press rocker switch

3-zone automatic climate control
XActivate or deactivate the "Synchronization"function using the multimedia system(Ypage 273).
The synchronization function is deactivated:
Rif the settings for the front-passenger side arechanged
Rthe settings for the rear compartment arechanged
Defrosting the windshield
General notes
You can use this function to defrost the wind-shield or to clear a fogged up windshield or frontside windows on the inside.
Switch off the "Windshield defrosting" functionas soon as the windshield is clear again.
Switching the "Windshield defrosting"
function on or off
XTurn the SmartKey to positionHin the igni-tion lock (Ypage 131).
XTo switch on:press rocker switchdonthe front control unit up or down.The indicator lamp above thedrockerswitch lights up. The current climate controlsettings are deactivated.
The climate control system switches to thefollowing functions:
Rhigh airflow
Rhigh temperature
Rair distribution to the windshield and frontside windows
Rair-recirculation mode off
iIf necessary, the "Cooling with air dehumid-ification" function is activated. In this case,the indicator lamp above theZrockerswitch remains switched off.
XTo switch off:press rocker switchdup ordown.The indicator lamp above thedrockerswitch goes out. The previously selected set-
tings are restored. Air-recirculation moderemains deactivated.
Removing condensation from the win-
dows
Windows fogged up on the inside
XActivate the "Cooling with air dehumidifica-tion" function with theZrocker switch.
XSwitch on automatic mode using theXrocker switch.
XIf the windows continue to fog up, activate the"Windshield defrosting" function using thedrocker switch.
iYou should only select this setting until thewindshield is clear again.
Windows fogged up on the outside
XActivate the windshield wipers.
XSwitch on automatic mode using theXrocker switch.
iIf you clean the windows regularly, they donot fog up so quickly.
Rear window defroster
General notes
The rear window defroster has a high currentdraw. You should therefore switch it off as soonas the rear window is clear. Otherwise, the rearwindow defroster switches off automaticallyafter several minutes.
If the battery voltage is too low, the rear windowdefroster may switch off.
Activating/deactivating
XTurn the SmartKey to positionHin the igni-tion lock (Ypage 131).
XPress rocker switchlup or down.The indicator lamp above rocker switchllights up or goes out.
Operating the climate control systems125
Climate control

Problems with the rear window defroster
ProblemPossible causes/consequences andPPSolutions
The rear windowdefroster has deactiva-ted prematurely or can-not be activated.
The battery has not been sufficiently charged.
XSwitch off any consumers that are not required, e.g. reading lamps,interior lighting or the seat heating.When the battery is sufficiently charged, the rear window defrostercan be activated again.
Switching air-recirculation mode
on/off
General notes
You can also temporarily deactivate the flow offresh air manually if unpleasant odors are enter-ing the vehicle from outside. The air alreadyinside the vehicle will then be recirculated.
If you switch on air-recirculation mode, the win-dows can fog up more quickly, in particular atlow temperatures. Only use air-recirculationmode briefly to prevent the windows from fog-ging up.
Activating/deactivating
XTurn the SmartKey to positionHin the igni-tion lock (Ypage 131).
XTo activate:press therrocker switch upor down.The indicator lamp above therrockerswitch lights up.
Air-recirculation mode switches on automati-cally:
Rat high outside temperatures
Rat high levels of pollution (3-zone automaticclimate control only)
Rin a tunnel (vehicles with a navigation systemonly)
The indicator lamp above therrockerswitch is not lit when automatic air-recirculationmode is activated. Outside air is added afterabout 30 minutes.
XTo deactivate:press therrocker switchup or down.The indicator lamp above therrockerswitch goes out.
Air-recirculation mode deactivates automati-cally:
Rafter approximately five minutes at outsidetemperatures below approximately 41 ‡(5 †)
Rafter approximately five minutes if coolingwith air dehumidification is deactivated
Rafter approximately 30 minutes at outsidetemperatures above approximately 41 ‡(5 †) if the "Cooling with dehumidification"function is activated
Switching the residual heat on or off
General notes
The residual heat function is only available with3-zone automatic climate control.
Once the engine is switched off, it is possible tomake use of the residual heat of the engine tocontinue heating or ventilating the front com-partment of the vehicle for approximately30 minutes. The heating or ventilation timedepends on the interior temperature that hasbeen set.
Activating/deactivating
XTurn the SmartKey to position

XTo refill the perfume vial:unscrew the lid ofthe empty perfume vial to refill it yourself.
XFill the perfume vial with a maximum of0.5 fl. oz. (15 ml) of the desired liquid per-fume.
XScrew the lid back on to the vial.
!Only refill the perfume vial when you areoutside the vehicle. Otherwise, liquid perfumecould drip into the interior and contaminate it.
Always refill the empty refillable vial with thesame perfume. Otherwise, you might not ach-ieve optimum results from the perfume atom-izer.
Problems with the perfume atomizer
ProblemPossible causes/consequences andPPSolutions
The vehicle interior is notperfumed although theperfume atomizer is acti-vated.
The perfume vial has not been pushed into the holder as far as it willgo.
XSlide the perfume vial into the holder as far as it will go.
The perfume vial is not filled sufficiently.
XPre-filled vials:dispose of the empty vial.
XUse a new pre-filled vial.
XRefillable vials:refill the vial with a maximum of 0.5 fl. oz. (15 ml)of the same perfume.
The perfume atomizer is faulty.
XHave the perfume atomizer checked at a qualified specialist work-shop.
Ionization
Ionization is used to purify the air in the vehicleinterior and attain an improved interior climate.
The ionization of the interior air is odorless andcannot be perceived directly in the vehicle inte-rior.
You can switch ionization on/off using the mul-timedia system (Ypage 273).
Ionization can only be operated when the auto-matic climate control is switched on. The side airvent on the driver's side must be open.
Air vents
Important safety notes
GWARNING
Very hot or very cold air can flow from the air
vents. This could result in burns or frostbite in
the immediate vicinity of the air vents. There
is a risk of injury.
Make sure that all vehicle occupants always
maintain a sufficient distance to the air out-
lets. If necessary, redirect the airflow to
another area of the vehicle interior.
In order to ensure the direct flow of fresh airthrough the air vents into the vehicle interior,please observe the following notes:
Rkeep the air inlet between the windshield andthe hood free of blockages, such as ice, snowor leaves.
Rnever cover the air vents or air intake grilles inthe vehicle interior.
128Air vents
Climate control

GWARNING
If you switch off the ignition while driving,
safety-relevant functions are only available
with limitations, or not at all. This could affect,
for example, the power steering and the brake
boosting effect. You will require considerably
more effort to steer and brake. There is a risk
of an accident.
Do not switch off the ignition while driving.
GWARNING
If the parking brake has not been fully
released when driving, the parking brake can:
Roverheat and cause a fire
Rlose its hold function.
There is a risk of fire and an accident. Release
the parking brake fully before driving off.
!Do not warm up the engine while stationary.Pull away immediately. Avoid high enginespeeds and full throttle until the engine hasreached its operating temperature.
In vehicles with automatic transmission,engage positions P and R only when the vehi-cle is stationary.
Where possible, avoid spinning the drivewheels when pulling away on slippery roads.You could otherwise damage the drive train.
!Mercedes-AMG vehicles:at low engine oiltemperatures below 68 ‡ (+20 †), the max-imum engine speed is restricted in order toprotect the engine. To protect the engine andmaintain smooth engine operation, avoid driv-ing at full throttle when the engine is cold.
Key positions
SmartKey
ZTo remove the SmartKey
GPower supply for some consumers, such asthe windshield wipers
HIgnition (power supply for all consumers)and drive position
ITo start the engine
iThe SmartKey can be turned in the ignitionlock even if it is not the correct SmartKey forthe vehicle. The ignition is not switched on.The engine cannot be started.
Start/Stop button
General notes
When you insert the Start/Stop button into theignition lock, the system needs approximatelytwo seconds recognition time. You can then usethe Start/Stop button.
Pressing the Start/Stop button several times insuccession corresponds to the different Smart-Key positions in the ignition lock. This is only thecase if you are not depressing the brake pedal.
If you depress the brake pedal and press theStart/Stop button, the engine starts immedi-ately.
A check which periodically establishes a radioconnection between the vehicle and the Smart-Key determines whether a valid SmartKey is inthe vehicle. This occurs, for example, whenstarting the engine.
Driving131
Driving and parking
Z

To start the vehicle without actively using theSmartKey:
Rthe Start/Stop button must be inserted in theignition lock.
Rthe SmartKey must be in the vehicle.
Rthe vehicle must not be locked with theSmartKey or KEYLESS-GO. (Ypage 78)
Do not keep the SmartKey:
Rwith electronic devices, e.g. a mobile phoneor another SmartKey.
Rwith metallic objects, e.g. coins or metal foil.
Rinside metallic objects, e.g. a metal case.
This can affect the functionality of the Smart-Key.
If you lock the vehicle with the SmartKey remotecontrol or with KEYLESS-GO, after a short time:
Ryou will not be able to switch on the ignitionwith the Start/Stop button.
Ryou will no longer be able to start the enginewith the Start/Stop button until the vehicle isunlocked again.
If you lock the vehicle centrally using the buttonon the front door (Ypage 83), you can continueto start the engine with the Start/Stop button.
The engine can be switched off while the vehicleis in motion by pressing and holding the Start/Stop button for three seconds. This functionoperates independently of the ECO start/stopautomatic engine switch-off function.
Key positions with the Start/Stop button
CStart/Stop button
DIgnition lock
As soon as the ignition is switched on, all theindicator lamps in the instrument cluster lightup. Warning and indicator lamps: see(Ypage 256).
If Start/Stop buttonChas not yet beenpressed, this corresponds to the SmartKeybeing removed from the ignition.
XTo switch on the power supply:pressStart/Stop buttonConce.The power supply is switched on. You can nowactivate the windshield wipers, for example.
The power supply is switched off again if:
Rthe driver's door is opened and
Ryou press Start/Stop buttonCtwice when inthis position
XTo switch on the ignition:press Start/StopbuttonCtwice.The ignition is switched on.
The ignition is switched off again if:
Ryou do not start the engine from this positionwithin 15 minutes
Ryou press Start/Stop buttonConce when inthis position
The power supply is switched off again if:
Rthe driver's door is opened and
Ryou press Start/Stop buttonConce when inthis position
Removing the Start/Stop button
You can remove the Start/Stop button from theignition lock and start the vehicle as normalusing the SmartKey.
It is possible to switch between Start/Stop but-ton mode and key operation only when thetransmission is in position].
XRemove Start/Stop buttonCfrom ignitionlockD.
You do not have to remove the Start/Stop but-ton from the ignition lock when you leave thevehicle. You should, however, always take theSmartKey with you when leaving the vehicle. Aslong as the SmartKey is in the vehicle:
Rthe vehicle can be started using the Start/Stop button
Rthe electrically powered equipment can beoperated
132Driving
Driving and parking