ECO mode MERCEDES-BENZ M-CLASS SUV 2011 Owner's Guide

Usefu
linfor mati on
i This Owner's Manual describes all models
and all standard and optional equipment
available to your vehicle at the time of pub-
lication of the Owner's Manual. Country-
specific deviation sare possible .Please
not ethat your vehicle ma ynot be equipped
with all featur es described. This also
applies to safety-releva ntsystems and
functions.
i Please read the information on qualified
specialist workshops (Y page 24).Important safet
ynotes G
WARNING
Tyres, wheels or accessories whic hhaven ot
been approved by Mercedes- Benz foryour
vehicle or are not used as they should be, can
impair driving safety. As aresult, you could
cause an accident .Befor epurchasing and
using them, enquire about their suitability,
legal stipulations and factory recommenda-
tions at aMercedes-Benz Ser vice Centre.
Modificatio nwork on the brake system and
wheels is not permitted, nor is the use of
spacer plate sorbrake dust shields. This inva-
lidates th eGeneral Operatin gPermit for the
vehicle.
i Further information about tyres and
wheels can be obtained from any
Mercedes-Benz Ser vice Centre. Oper
ation Notes on driving
R While driving, pay attention to vibrations,
noises and unusual handling characteris-
tics ,e.g. pulling to one side. This may indi-
cate that the wheels or tyres are damaged.
If you suspect that atyre is defective,
reduce your speed immediately. Stop the vehicle as soo
naspossible to chec kthe
wheels and tyres for damage. Hidden tyre
damage could also be causing the unusual
handling characteristics. If you fin dno
signs of damage, hav ethe wheels and tyres
examined at aqualified specialist work-
shop, e.g. aMercedes-Ben zService
Cent re.
R When parkin gyour vehicle, make sure that
the tyres do not get deformed by the kerb
or other obstacles. If it is necessary to drive
over kerbs, speed humps or similar eleva-
tions, tr ytodosos lowly and at an obtuse
angle. Otherwise, the tyres, particularly the
sidewalls, can get damaged. Notes on regularly inspecting wheels
and tyres
R Regularly chec kthe wheels and tyres of
your vehicle for damage (e.g. cuts, punctu-
res, tears, bulges on tyres and deformation,
crack sorseverecorrosion on wheels), at
least ever y14d ays, as well as after driving
off-road or on rough roads. Damaged
wheels can cause aloss of tyr epressure.
R Regu larly check th etyre tread depth and
the conditio nofthe tread across the whole
widt hofthe tyr e(Ypage 357). If neces-
sary, tur nthe front wheels to full lock in
orde rtoi nspect the inner sid eofthe tyre
surface.
R All wheels must hav eavalve cap to protect
the valve against dirt and moisture. Do not
fit anything onto the valve (such as tyre
pressure monitorin gsystems) othe rthan
the standar dvalve cap or other valve caps
approved by Mercedes-Ben zfor your vehi-
cle.
R Regularly chec kthe pressur eofall the tyres
including the emergenc yspare wheel or the
spare wheel, particularly prior to long trips,
and correc tthe pressur easnecessary
(Y page 359). 356
OperationWheels and tyres

M+S tyres
At temperature sbelo w+ 7† ,use winter tyres
or all-season tyres .Both types of tyr eare
identified by th eM+S marking.
Onl ywinter tyres bearing the isnowflake
symbol in addition to the M+S marking pro-
vide the best possible grip in wintr yroad con-
ditions. Only these tyres will allow driving
safet ysystems such as ABS and ESP ®
to
function optimally in winter, as thes etyres
have been designed specifically for driving on
snow.
Use M+S tyres of the same make and tread
on all wheels to maintain safe handling char-
acteristics. G
WARNING
M+S tyres with atrea ddepth of less than
4mmm ust be replaced. They are no longer
suitable for winter use and can no longer pro-
vide sufficien tgrip. This could cause you to
lose control of your vehicle and cause an acci-
dent.
Always observe the maximum permissible
speed specified for the M+S tyres you have
fitted.
If you fit M+S tyres which have alower max-
imu mpermissible speed than that of the vehi-
cle, affix an appropriate warning sign in the
driver' sfield of vision. This can be obtained
at aq ualified specialist workshop, e.g. at a
Mercedes-Ben zService Centre.
Under these circumstances, you should also
restrict the maximu mspeed of the vehicle
using permanent SPEEDTRONIC so that it
does not exceed the maximum permissible
speed for the M+S tyres(Y page 174).
When you have fitted the M+S tyres:
X Check the tyr epressures (Y page 359).
X Restart th etyre pressure los swarning sys-
tem (Y page 360). G
WARNING
If you fit the spare wheel when driving with M
+S tyres, bear in mind that driving stability will be impaired due to unstable cornerin
gchar-
acteristic scaused by the different tyres. You
shoul dtherefore adapt your drivin gstyle and
drive carefully.
Have the spare whee lreplaced at the nearest
qualified specialist workshop which has the
necessar yspecialist knowledge and tools to
carry out the work required. Mercedes-Benz
recommends that you use aMercedes-Benz
Ser vice Centre for thi spurpose. In particular,
work relevant to safety or on safety-related
systems must be carried out at aqualified
specialist workshop. Snow chains
For safety reasons ,Mercedes-Benz recom-
mends that you only use snow chain sthat
hav ebeen specially approved for your vehicle
by Mercedes-Benz ,orthat ar eofac orre-
spondin gstandard of quality.
! Vehicle swith the ON&OFFROAD package
or the AIRMATIC package: do not drive in
ADS SPORT mode when drivin gwith snow
chains fitted.
If you intend to fit snow chains, please bear
the following point sinmind:
R it is not permissible to attac hsnow chains
to all wheel-tyre combinations ;see the
information under "Wheel/tyre combina-
tion s"int he "Wheels and tyres" section.
R snow chains must not be fit tedtoe mer-
gency spare wheels ,e.g. a"Minispare"
emergency spar ewheel.
R fit snow chains only in pair sand only to the
rear wheels .Observ ethe manufacturer's
installation instructions.
! Vehicle swith steel wheels: if you wish
to fit snow chains to steel wheels, make
sure that you remove the respective
wheels' hubcaps first .The hubcaps may
otherwise be damaged. 358
Winter operationWheels and tyres

obtained from any Mercedes-Benz Service
Centre.
! Retreaded tyres ar eneither tested nor
recommended by Mercedes-Benz, since
previous damage can nota lways be detec-
ted on retreaded tyres. As aresult,
Mercedes-Benz can notg uarantee vehicle
safety if retreaded tyres are fitted. Do not
fit used tyres if you have no information
about their previous usage.
! Large wheels: the lower the section width
for acertain wheel size, the lower the ride
comfor tisonp oor roadsurfaces. Roll com-
fort and suspensio ncomfort ar ereduced
and the risk of damage to the wheels and
tyres as aresult of driving over obstacles
increases.
i You will fin datable of tyre pressures on
the inside of your vehicle's fuel filler flap.
For further information on tyre pressure,
see (Y page 359).
i Notes on the vehicle equipment –always
fit the vehicle:
R with tyre softhe sam esize on agiven axle
(left/right)
R with the same type of tyre satagiven
tim e(sum mertyres, winter tyres,
MOExtended tyres)
i Vehicles with MOExtended tyre sare not
equippe dwithaTIREFIT kit at th efactory.
It is therefore recommended that you addi-
tionally equip your vehicle with aTIREFIT kit
if yo ufit tyre sthat do not fea ture run-flat
prope rties, e.g. winter tyres. ATIREFIT kit
can be obtaine dfrom aMercedes-Benz
Servic eCentre.
i Overview of abbreviation sused in the fol-
lowin gtyre tables:
R BA: both axles
R FA: front axle
R RA: rear axle In the following table, the wheel/tyre combi-
nations are allocate
dtothe vehicle models
through variants, e.g. V1 ,V2etc.: V1
V2
V3
i
Not all wheel/tyre combinations can be
mounted at the factory in all countries. Wheel and tyr
ecombinations
365Wheels andtyres Z
ML 25
0BlueTEC 4MATIC
ML 350 4MATIC
ML 350 BlueTEC 4MATIC

Usefu
linfor mati on
i This Owner's Manual describes all models
and all standard and optional equipment
available to your vehicle at the time of pub-
lication of the Owner's Manual. Country-
specific deviation sare possible .Please
not ethat your vehicle ma ynot be equipped
with all featur es described. This also
applies to safety-releva ntsystems and
functions.
i Please read the information on qualified
specialist workshops (Y page 24).Note
sont hetechnical data
You can fin dtechnica ldatao nthe Internet at:
http://www.mercedes-benz.com
i The technical dat awas determined in
accordance wit hECDirectives. All data
applies to th evehicle's standard equip-
ment. Therefore, th edatam ay differ for
vehicles wit hoptional equipment. You can
obtain further information from a
Mercedes- BenzService Centre. Genuine Mercedes-Ben
zparts
Mercedes-Ben ztests genuin eparts and con-
version parts and accessories which have
been specifically approved for your vehicle for
their reliability, safety and suitability. Despite
ongoing market research, Mercedes -Benz is
unabl etoe valuat eother parts. Mercedes-
Benz therefore accepts no responsibility for
the use of such parts in Mercedes-Ben zvehi-
cles, even if they have been independently or
officially approved.
In Germany and some other coun tries, certain
parts are only officially approved for installa-
tion or modification if they comply with legal
requirements. All genuine Mercedes-Benz
parts meet this requirement .The use of non- approved parts ma
yinvalidat ethe vehicle's
general operating permit. This is the case if:
R they cause achange of the vehicle type
from that for whic hthe vehicle' sgeneral
operating permit was granted.
R other road users could be endangered.
R the emission or noise levels are adversely
affected. G
WARNING
Drivin gsafety may be impaired if non-
approved parts, tyres and wheels or safety-
relevant accessories are used.
This could lead to malfunctions in safety-rel-
evant systems, e.g. the brake system. This
could cause you to lose control of your vehicle
and cause an accident.
For this reason, Mercedes-Benz recommends
that you use genuine Mercedes-Benz parts or
parts of equal quality. Only use tyres, wheels
and accessories that have been specifically
approved for your vehicle.
! Airbags and sea tbelt tensioners, as well
as control unit sand sensors for these
restraint systems may be installed in the
following areas of your vehicle:
R doors
R doo rpillars
R door sills
R seats
R dashboard
R instrument cluster
R centre console
Do not install accessories such as audio
systems in these areas. Do not carr yout
repairs or welding .You coul dimpair the
operating efficie ncyoft he restraint sys-
tems.
Hav eaftermarket accessories installe dat
aq ualified specialist workshop. Mercedes-
Benz recommends that you use a
Mercedes -Benz Ser vice Centre for thi spur-
pose. 370
Genuine Mercedes-Benz partsTechnical data

AdBlue
®
residue crystallises afte racertain
amount of time and soils the affecte dsur-
faces.
Hig houtside temperatures If AdBlue
®
is heate dtoabove 50 †for an
extended perio doftime,AdBlue ®
may start
to decom pose,e .g.d ue to direc tsunlight on
the AdBlue ®
tank. Ammonia vapour sdevelop
as aresult. G
WARNING
Ammonia vapours may escape if the
AdBlue ®
tan kcap is opened at high tempera-
tures. Ammonia vapours have apungent
odour and are particularly irritating to the
skin, to mucous membranes and to the eyes.
You may experienc eaburning sensation in
your eyes, nose and throat ,aswell as cough-
ing and waterin goftheeyes.
Do no tinhale ammoni avapours.
Lo wo utside temperatures AdBlue
®
freezes at atemperatur eofapp rox-
imatel y–11 †. Th evehicle is equip pedw ith
an AdBlue ®
preheating system at the factory.
Winter operatio ncan thus be guaranteed
even at temperatures below –11 †.
Additives !
Only use AdBlue ®
in accordan cewit hISO
22241. Do not us eadditives wit hAdBlue ®
an ddon ot dilute AdBlue ®
with water. This
may destroy th eBlueTEC exhaust gas after-
treatmen tsystem.
Purity Assuring the purity of AdBlue
®
is particularly
important with respect to avoiding malfunc-
tions in the exhaus tgas aftertreatment sys-
tem.
If AdBlue ®
is pumped out of the AdBlue ®
tank,
e.g. during repair work, do not use this fluid to refill the tank
.The purity of the fluid can no
longer be guaranteed.
! Impuritie sinAdBlue ®
(e.g. due to other
service products, cleaning agents or dust)
lead to:
R increased emission values
R damage to the catalytic converter
R engine damage
R ®
exhaust
Tota lcapacity of the AdBlue ®
tank Model Total
capacity 27.5 l
Engine oil
Th
eq uality of engine oils is decisive for the
function and service life of an engine. After
extensive tests, Mercedes-Benz approves
engine oils that correspond to the current
technical standard.
Therefore, only Mercedes-Benz approved
engine oils may be used in Mercedes-Benz
engines.
Further information on tested and approved
engine oils can be obtained from any
Mercedes-Benz Service Centre. Mercedes-
Benz recommends that you have the oil
change carried out at aMercedes-Benz
Ser vice Centre. Mercedes-Ben zapproval is
indicated on the oil container by the inscrip-
tion "MB Approval" and the cor respondi ng
designation, e.g. MB Approval 22 9.51.
Th et able shows which engine oils have been
approved for your vehicle. Petrol engines MB Approval
M3
50 4MATIC 22
9.3, 229.5 Servic
eproducts and capacities
375Technicaldata Z
malfunctions in the BlueTEC
gas aftertreatment system
ML 250 BlueTEC 4MATIC
Please bear the following in mind ML
350 BlueTEC 4MATIC

Diesel engines MB Approval
228.51,
229.31 ,229.51 engine oils on the Interne
tat
http:/ /bevo. mercedes -benz.com by enter-
ing the designation, e.g. 22 9.5.
i If the engine oils listed in the table are not
available ,you ma yadd the followin gengine
oil su ntil the next oil change:
R vehi cles with apetrol engine: MB
Approval 22 9.1orA CEAA3
R vehicles wit hadiesel engine: MB
Approval 229.1 or ACE AC3
Engine oil may only be adde donce, and no
mor ethan 1. 0lmay be added.
Capacities The following values refer to an oil change
including the oil filter. Model Capacity
7.0 l
7.8 l
8.0 l
Additives
!
Do not use additive sinengine oil .This
could damage the engine.
Engine oil viscosity Viscosit
ydescribes the flow characteristi cs
of afluid. If an engin eoil has ahigh viscosity
rating, it flows slowly; the lower the viscosity,
the faster it flows.
Engine oil selection is based on the respective
outside temperatures and in accordance with
the SA Eclassification (viscosity). The table
below shows you which SA Eclassifications are to be used. The low-temperature proper-
ties of engin eoils can be significantly
impaired durin goperation due to, for exam-
ple, ageing or soot and fuel accretion. It is
therefore strongly recommende dtoobserve
regula roil changes using an approved engine
oil with the appropriate SA Eclassification. Brake fluid
G
WAR
NING
Over aperiod of time, the brak efluid absorbs
moisture fro mthe air ;This lower sits boiling
point.
If the boiling point of the brake fluid is too low,
vapour pockets may form in the brake system
when the brakes are applied hard (e.g. when
driving downhill). Thi simpairs brakin geffi-
ciency.
Yo us hould hav ethe brake fluid renewed at
regular intervals. The brake fluid change inter-
vals can be found in the Servic eBooklet.
Only use brak efluid approved by Mercedes-
Benz .Information abou tapproved brak eflu-
ids can be obtained from any Mercedes-Benz
Service Centr eoronthe Internet at
http://bevo. mercedes-benz.com
i There is usuall yanoticeint he engine
compartmen ttoremin dyou when the next
brake fluid change is due. 376
Service products and capacitiesTechnical data
You can cal
lupanoverview of ap proved
ML
350 BlueTEC 4MATIC
Vehicles wit
hadiesel particle filter
ML 250 BlueTEC 4MATIC
ML 350 4MATIC
ML 350 BlueTEC 4MATIC
ML
250 BlueTEC 4MATIC

Coolant
Important safety notes The coolan
tisamixture of water and anti-
freeze/corrosio ninhibitor. It performs the
following tasks:
R anti-corrosio nprotection
R antifreeze protection
R raising th eboiling point
i When the vehicle is first delivered, it is fil-
led with acoolant mixtur ethat ensures
adequate antifreeze and corrosion protec-
tion.
! Only add coolant that has been premixed
with the desired antifreeze protection. The
engin ecould otherwise be damaged.
Further information on coolants and on fill-
ing can be found in the Mercedes-Benz
Specifications for Servic eProducts ,MB
Approval 310.1 ,e.g. on the Internet at
http ://bevo.mercedes-benz.com .You can
also consult aMercedes-Benz Service
Centre.
! Alway suseasuitable coolant mixture,
even in countries where high temperatures
prevail.
Otherwise, the engine cooling system is not
sufficiently protected from corrosion and
overheating.
If antifreeze/corrosio ninhibitor is present in
the correc tconcentration, the boilin gpoint of
the coolant during operation will be around
13 0†.
The antifreeze/ corrosion inhibitor con centra-
tion in the engine cooling system should:
R be at leas t50%. This wil lprotect the engine
coolin gsystem agains tfreezin gdown to
around -3 7†.
R not excee d55% (antifreeze protection
down to -45 †);otherwise, heat will not be
dissipated as effectively.
If the vehicle has los tcoolant, top it up with
equal amount sofwater and antifreeze/cor- rosion inhibitor. Mercedes-Benz recom-
mends an antifreeze/corrosion inhibitor
which has been approved for Mercedes-Benz.
! The engin ecoolin gsystem is filled with
coolant that must be renewed after 15
years, or after 250,000 km at the lates t. Vehicl
edata
Pleas enotet hat for the speci fied vehicle
data:
R the height sspecified may var yasaresult
of:
- tyres
- load
- conditio nofthe suspen sion
- optional equipment
R item sofo ptional equipmen tincrease the
unlade nweight and reduc ethe maximum
payload. The unladen weight is speci fied in
accordanc ewith EC directive and includes:
- driver (68 kg)
- luggage (7 kg)
- all fluids (fuel tan k90% full)
R veh icle-specific weigh tinformation can be
found on the vehicl eidentification plate
(Y page 37 2).
R only for cer tain countries: you can find vehi-
cle-specific vehicle data in the COC docu-
ment s(CERTIFICATE OF CONFORMITY).
Thes edocuments ar edelivered with your
vehicle.
Missing values were not available at tim eof
going to print. All models
Vehicle lengt
h(ECE) 480
4mm Vehicle width
including exterior
mirrors
214
1mm Vehicle width with-
out exterior mirrors 192
6mm Vehicl
edata
377Techni caldata Z

All models
Wheelbase
2915 mm
Unladen weight
Maximu
mroofload 10
0kg Vehicle height
178
8mm Ground clearance
191 mm
1796 mm
Ground clearance
202 mm
Tailg
ateo pening dimensions Models with: :
Opening
height ;
Maximum
headroom Stee
lsuspen-
sion 2195 mm 1987 mm
Steel suspen-
sion
33 2187 mm 1980 mm
AIRMATIC
package
34 2140 –
2215 mm 1931 –
2006 mm Traile
rtow hitch Mounting dimensions
G
WARNING
Only have atrailer tow hitch retrofit tedata
qualified specialist workshop which has the
necessary specialist knowledge and tools to
carry out the work required. Mercedes-Benz
recommends that you use aMercedes-Benz
Ser vice Centre for thi spurpose. In particular,
work relevant to safety or on safety-related
systems must be carried out at aqualified
specialist workshop.
! If you have atrailer to whitchr etrofit ted,
changes to the cooling system and drive
train may be necessary, depending on the
vehicle type.
observe the anchorage points on th echas-
sis frame.
! trailer tow hitc hfitted retrospectively with-
out changing the engine cooling system
and the drive train ,the braked and
unbraked tota ltowing weight (trailer
weight plus load weight) is reduced. Miss-
ing values wer enot available at tim eof
going to print. If higher towin gweight sare
used ,this can result in damage to your
vehi cle's engine. An ydamage that may
33
34 On vehicles with the ON&OFFROAD package, the value increases by 30 mm. 378
Trailer tow hitchTechnica
ldata
ML 250 BlueTEC 4MATIC
ML 350 4MATIC
Vehicle height
ML
350 BlueTEC 4MATICC
ML 250 BlueTEC 4MATIC:if you have a
If you have
atrailer to whitchr etrofit ted,
ML 25 0BlueTE C4MATIC.