light MERCEDES-BENZ METRIS 2020 MY20 Operator’s Manual

Seat belts
Warning/
indicator
lamp
N Signal type
Possible causes/consequences and
M Solutionsü
N After starting the engine, the red seat belt warning lamp lights up or flashes.
A warning tone may also sound.
Only for certain countries: the red seat belt warning lamp lights up for a maxi-
mum of 6 seconds after the ignition is switched on.
The seat belt warning lamp reminds the driver and front-passenger to fasten
their seat belts.
X Fasten seat belt ( Y page 50).ü
N The red seat belt warning lamp lights up after the engine starts, as soon as
the driver's or the front-passenger door is closed.
The driver or front-passenger has not fastened their seat belt.
X Fasten seat belt (Y page
50).
The warning lamp goes out.
On vehicles with the Occupant Classification System (OCS), there are objects
on the front-passenger seat.
X Remove the objects from the front-passenger seat and store them in a safe
place.
The warning lamp goes out. ü
N The red seat belt warning lamp flashes and an intermittent audible warning
sounds.
The driver or front passenger has not fastened their seat belt. At the same time,
you are driving faster than

15 mph (25 km/h) or have briefly driven faster than
15 mph (25 km/h).
X Fasten seat belt (Y page
50).
The warning lamp goes out and the intermittent audible warning ceases.
On vehicles with the Occupant Classification System (OCS), there are objects
on the front-passenger seat. At the same time, you are driving faster than
15 mph (25 km/h

) or have briefly driven faster than 15 mph (25 km/h).
X Remove the objects from the front-passenger seat and store them in a safe
place.
The warning lamp goes out and the intermittent warning tone ceases.228
Indicator and warning lamps in the instrument cluster
On-board computer and displays

Engine
Warning/
indicator
lamp
N Signal type
Possible causes/consequences and
M Solutions;
N The yellow Check Engine warning lamp lights up while the engine is running.
There may be a malfunction in the following vehicle systems:
R in the engine management
R in the transmission management
R in the fuel injection system
R in the exhaust system
R in the ignition system (for vehicles with a gasoline engine)
R in the fuel system
The emission limit values may be exceeded and the engine may be running in
emergency mode.
X Have the vehicle checked as soon as possible at a qualified specialist work-
shop. 6
N The yellow reserve fuel warning lamp is on while the engine is running.
The fuel level has dropped to the reserve range.
X Refuel at the nearest gas station. ?
N The red coolant warning lamp comes on while the engine is running.
On vehicles without steering wheel buttons, the coolant temperature gauge is at
the start of the bar display
(Y page 178).
On vehicles with steering wheel buttons, the coolant temperature gauge is at
the start of the scale in the instrument cluster ( Y page 40).
The temperature sensor for the coolant temperature gauge is faulty.
The coolant temperature is no longer being monitored. There is a risk of engine
damage if the coolant temperature is too high.
X Stop the vehicle immediately, paying attention to road and traffic conditions,
and switch off the engine. Do not continue driving under any circumstances.
X Secure the vehicle to prevent it from rolling away (Y page
138).
X Consult a qualified specialist workshop. Indicator and warning lamps in the instrument cluster
233
On-board computer and displays Z

Warning/
indicator
lamp
N Signal type
Possible causes/consequences and
M SolutionsX
Secure the vehicle to prevent it from rolling away ( Y page 138).
X Exit the vehicle and keep a safe distance from the vehicle until the engine has
cooled down.
X Check the coolant level and add coolant, observing the warning notes
(Y page
253).
X If you have to add coolant more frequently, have the engine cooling system
checked.
X Make sure that the air supply to the radiator is not obstructed, by frozen
slush for example.
X Check the coolant temperature:
R using the display in the on-board computer on vehicles without steering
wheel buttons ( Y page

178)
R using the analog display in the instrument cluster on vehicles with steering
wheel buttons ( Y page 40)
X If the coolant temperature is below the maximum value specified below, you
can continue driving to the nearest qualified specialist workshop.
Avoid heavy loads on the engine, e.g. driving in mountainous terrain, and
stop-start traffic.
Under normal driving conditions and at the correct coolant level, the coolant
temperature display may rise to the letter H or to the red mark.Driving systems
Warning/
indicator
lamp
N Signal type
Possible causes/consequences and
M Solutions·
N The red distance warning lamp lights up while the vehicle is in motion.
The distance to the vehicle in front is too small for the speed selected.
X Increase the distance. ·
N The red distance warning lamp lights up while the vehicle is in motion. An
additional warning tone sounds.
You are approaching a vehicle or a stationary obstacle in your line of travel at
too high a speed.
X Be prepared to brake immediately.
X Pay particular attention to the traffic situation. You may have to brake or take
evasive action.
Further information about the distance warning function can be found under
"COLLISION PREVENTION ASSIST"
(Y page 149). Indicator and warning lamps in the instrument cluster
235
On-board computer and displays Z

X
To open: briefly press cover of eyeglasses
compartment :.
The eyeglasses compartment opens down-
wards.
X To close: press the cover of the eyeglasses
compartment : into the overhead control
panel until it engages.
Make sure that the eyeglasses compartment is
always closed while the vehicle is in motion. Stowage net
You can use the stowage nets on the back of
the seat backrests to store small, lightweight
items.
Observe the loading directions ( Y page
242)
and the safety information about the stowage
spaces (Y page 238). Sun visors
Overview
G
WARNING
If the mirror cover of the vanity mirror is fol-
ded up when the vehicle is in motion, you
could be blinded by incident light. There is a
risk of an accident.
Always keep the mirror cover folded down
while driving. Sun visor (example with illuminated vanity mirror)
:
Mirror light
; Retainer
= Retaining clip, e.g. for a parking ticket
? Vanity mirror
A Mirror cover Vanity mirror in the sun visor
X Fold up mirror cover A.
X Turn the key to position 1 or 2 in the igni-
tion lock.
Mirror lamp : lights up. Glare from the side
X Fold the sun visor down.
X Pull the sun visor out of bracket ;.
X Swing the sun visor to the side. Cup holder
Important safety notes
G
WARNING
The cup holder cannot hold a container
secure whilst traveling. If you use a cup
holder whilst traveling, the container may be
flung around and liquid may be spilled. The
vehicle occupants may come into contact
with the liquid and if it is hot, they may be
scalded. You may be distracted from the
traffic conditions and you could lose control
of the vehicle. There is a risk of an accident
and injury.
Only use the cup holder when the vehicle is
stationary. Only use the cup holder for con-
tainers of the right size. Always close the
container, particularly if the liquid is hot.
! Only use the cup holders for containers of
the right size and which have lids. The
drinks could otherwise spill.
Observe the loading guidelines

(Y page 242). Cup holder
239Stowing and features Z

Cup holders in the dashboard
Cup holder in the dashboard (example: left side
of vehicle)
Cup holders
: are located on the left and the
right on top of the dashboard and on the cen-
ter console. Bottle holder
The bottle holders are in front of the stowage
compartments in the front doors.
There are additional bottle holders on the left
and right in the rear compartment side panel-
ing. Observe the safety notes
(Y page 238). Ashtray
Front ashtray
Ashtray
Ashtray with lid : can be inserted into a cup
holder on the dashboard or into a cup holder
in the rear compartment. Cigarette lighter
Important safety notes
G
WARNING
You can burn yourself if you touch the hot
heating element or the socket of the ciga-
rette lighter.
In addition, flammable materials can ignite
if:
R the hot cigarette lighter falls
R a child holds the hot cigarette lighter to
objects, for example
There is a risk of fire and injury.
Always hold the cigarette lighter by the
knob. Always make sure that the cigarette
lighter is out of reach of children. Never
leave children unsupervised in the vehicle.
Above all, pay attention to traffic conditions.
You could otherwise cause an accident and
injure yourself and others. Only operate the
cigarette lighter if traffic conditions permit. 240
Cigarette lighter
Stowing and features

Cigarette lighter in the front com-
partment
X
To use the cigarette lighter: turn the key
to position 1 in the ignition lock
(Y page
127).
X Press in cigarette lighter :.
The cigarette lighter will pop out automati-
cally when the heating element is red-hot.
X Pull the cigarette lighter out of the socket by
its handle.
The cigarette lighter socket can be used for
accessories with a maximum power consump-
tion of 180 W

(15 A).
If you use the sockets to connect accessories
for long periods when the engine is switched
off, the starter battery may discharge. An
emergency cut-off ensures that the on-board
voltage does not drop too low. If the on-board
voltage is too low, power to the socket is auto-
matically cut. This ensures that there is suffi-
cient power to start the engine. 12 V socket
When the key is turned to position 1 in the
ignition lock, the sockets can be used for accessories with a maximum power consump-
tion of

180 W (15 A).
If you use the sockets for long periods when
the engine is switched off, the starter battery
may discharge. If the on-board voltage is too
low, it might then no longer be possible to
start the engine.
The socket in the center console and the
socket in the side of the cargo compartment
are not automatically deactivated if the on-
board voltage is low. The additional sockets in
the rear compartment are automatically deac-
tivated if the on-board voltage is low.
Additional 12 V sockets may be located in the
rear corner trim next to the tailgate and in the
side trim on the left and right-hand sides.
X Lift up the cover of socket :. Mobile communications equipment
G
WARNING
If you operate information and communica-
tion devices while driving, you may be dis-
tracted from the traffic conditions. You
could even lose control of the vehicle. There
is a risk of an accident.
Only operate these devices when the vehicle
is stationary.
Observe the legal requirements for the country
in which you are currently driving when operat-
ing mobile communication equipment.
Please remember, a navigation system does
not supply information on the load-bearing
capacity of bridges or the overhead clearance
of underpasses. The driver remains responsi-
ble for safety at all times.
You and others can suffer health-related dam-
age through electromagnetic radiation. By
using an exterior antenna, a possible health
risk caused by electromagnetic fields, as dis-
cussed in scientific circles, is taken into
account. Only have the exterior antenna instal-
led by a qualified specialist workshop.
Failure to observe the Mercedes-Benz installa-
tion specifications can result in the invalida-
tion of your vehicle's operating permit.
You will find information on retrofitting electri-
cal or electronic equipment under “Vehicle
electronics” (Y page

304). Mobile communications equipment
241
Stowing and features Z

locking). Use rigid load securing aids, such
as wedges, wooden fixings or padding.
X Attach secured and stabilized loads in all
directions to the cargo tie-down rings and
the guide rails in the rear compartment.
Only use tie downs, such as lashing nets
and lashing straps, that have been tested in
accordance with current standards.
When securing a load, always use the clos-
est cargo tie-down rings and pad sharp
edges for protection. Cargo tie-down points (example: Cargo Van)
Fixed cargo tie-down points on the floor
:
Guide/load rails
; Cargo tie-down rings
If your vehicle is equipped with guide/loading
rails : in the floor, you can place lashing rods
directly in front of and behind the load. The
lashing rods directly absorb the potential shift-
ing forces.
Securing loads on the cargo compartment
floor by lashing them down is only recommen-
ded for lightweight loads. Place non-slip mats
(anti-slip mats) under the load to increase load
security.
Spread the load evenly across the cargo tie-
down points/cargo tie-down rings. You will
find information on the maximum loading capacity of the cargo tie-down points under
"Cargo tie-down points and carrier systems"
(Y page
313).
Do not attempt to modify or repair the cargo
tie-down points/cargo tie-down rings or tie
downs. Read the information on qualified spe-
cialist workshops: (Y page 32).
Note for Passenger Vans (vehicle category
M1) on the cargo tie-down points/cargo
tie-down rings on the cargo compartment
floor Lashing angle for optimal load securing (example)
d
Vertical to the cargo compartment floor
e Cargo compartment floor
: Direction of propagation with 75° lashing
angle
; Direction of propagation with 45° lashing
angle
The lashing angle is between the cargo com-
partment floor and the tie downs. For optimal
load securing in accordance with the
ISO 27955 standard, the lashing angle must
be between 45° ; and 75° :. The maximum
nominal tension load of

350 daN for the cargo
tie-down rings in the cargo compartment floor
or in the guide rails may not be exceeded.
Note for commercial vehicles (vehicle cate-
gories N1) without partition
Vehicles that are approved as commercial
vehicles (vehicle category N1) do not meet the
ISO 27956 standard in the currently valid ver-
sion without a partition. The ISO 27956 stand-
ard describes the equipment for correctly
securing a load in delivery vehicles. When
using the vehicle for the transport of goods,
the retrofitting of the partition is strongly rec-
ommended as it is difficult to secure loads cor-
rectly in vehicles without a partition. Securing loads
245
Transporting loads Z

Lashing straps
Important safety notes
G
WARNING
If you attach the tie-down incorrectly when
securing the load, the following may occur in
the event of abrupt changes in direction,
braking maneuvers or an accident:
R the cargo tie-down rings may become
detached or the tie-down may tear if the
permissible load is exceeded
R the load may not be restrained.
This may cause the load to slip, tip over or
be tossed about, striking vehicle occupants.
There is a risk of an accident and injury.
Always tension the tie-downs in the proper
manner and only between the described
cargo tie-down rings. Always use tie-downs
designed specifically for the loads.
! Observe the information on the maximum
loading capacity of the individual cargo tie-
down points.
If you use several cargo tie-down points to
secure a load, you must always take the
maximum loading capacity of the weakest
cargo tie-down point into account.
If you brake hard, for example, the forces
acting could be up to several times the
weight force of the load. Always use multi-
ple cargo tie-down points in order to distrib-
ute the force absorption. Load the ancho-
rages evenly.
Always observe the operating instructions or
the notes of the lashing strap manufacturer for
the operation of the lashing strap.
Securing loads on the cargo compartment
floor by lashing them down is only recommen-
ded for lightweight loads. Place non-slip mats
(anti-slip mats) under the load to increase load
security. Notes and information on:
R the operation of the cargo tie-down rings
and cargo tie-down points can be found in
the "Securing a load" section
(Y page 244)
R the maximum loading capacity of the cargo
tie-down points can be found in the "Techni-
cal data" section ( Y page 313)
R the maximum loading capacity of the lashing
strap can be found on the lashing strap label
If the label is missing or illegible, the lashing
strap is ready to be discarded. Such a lash-
ing strap must be removed from use. If stickers have been included in the delivery:
X Clean the surface before sticker : is
affixed.
The stickers must be affixed to a flat, metal-
lic surface free from grease and dust.
X Affix stickers : on every side of the vehicle
in close proximity to the loading rails in a
clearly visible location. 246
Lashing straps
Transporting loads

X
Guide ratchet strap ? through slotted shaft
A from behind as illustrated and tighten it.
X Swing tensioning lever ; back and forth
until the ratchet strap has wound around
slotted shaft A two to three times.
X Press stop slider = outwards in the direc-
tion of the arrow and swing tensioning
lever ; to detent position 1.
X Release stop slider =.
The ratchet is closed and engaged. Tensioning lever in the release position
X To release the ratchet strap: release ten-
sioning lever ; and swing it into release
position 7.
Lock stop slider = engages in end recess
B.
X Unlock the release catch D by pressing it.
Slotted shaft A can move freely.
X Pull ratchet strap ? out of the ratchet. Securing loads
Load protection net
G
WARNING
The load protection net alone cannot
restrain or secure heavy objects, luggage or
heavy loads. In the event of abrupt changes
in direction, braking maneuvers or an acci-
dent, you may be struck by unsecured loads.
There is a risk of injury, possibly even fatal.
Always stow objects in such a way that they
cannot be tossed about. Secure objects, lug-
gage and loads to prevent them slipping or
tipping over, e.g. by lashing them down,
even when using the load protection net. G
WARNING
If vehicle occupants are seated behind a
load protection net, they may be squeezed
up against the load protection net. There is
a risk of injury, particularly in the event of
braking maneuvers or abrupt changes in
direction.
Never allow vehicle occupants to sit behind
the load protection net.
The load protection net borders the cargo
compartment. It protects vehicle occupants
from light objects and/or luggage slipping or
tipping over. Always observe the notes on
securing loads
(Y page 244).
You can install the load protection net at an
angle behind the front seats or behind the first
row of back seats. Upper retainer
Anchorage (example: fixed cargo tie-down ring)248
Securing loads
Transporting loads

X
Hold support strut ? and lift the hood
slightly.
X Guide support strut ? towards retainer =
and apply slight pressure to make it engage.
X Lower the hood and allow it to fall with
momentum from a height of approximately
1 ft (30 cm
).
The hood locks audibly.
X Check that the hood is correctly locked.
If the hood can be raised slightly, it is not
properly engaged. If the hood is not cor-
rectly engaged, open the hood again. Let
the hood fall with a little more momentum. Overview of the engine compart-
ment
Engine compartment (example)
:
Engine oil filler neck cap (Y page
252)
; Brake fluid reservoir cap (Y page
255)
= Coolant expansion tank cap ( Y page
253)
? Washer fluid reservoir cap (Y page
256)
Regularly check the fluid level and the assem-
bly for leaks. If you detect fluid loss, e.g. oil
stains on the vehicle parking space, consult a
qualified specialist workshop immediately. Engine oil
General notes !
Engine oil gets dirty in the course of opera-
tion and its quality and volume are gradually
diminished. Regularly check the oil level,
and top up or have it replaced as needed.
Observe the information on approved engine
oils and oil consumption under "Service prod-
ucts and capacities" ( Y page

308).You can check the oil level in the engine:
R with the oil dipstick
Checking the oil level using the oil dip-
stick G
WARNING
Opening the hood when the engine is over-
heated or when there is a fire in the engine
compartment could expose you to hot gases
or other service products. There is a risk of
injury.
Let an overheated engine cool down before
opening the hood. If there is a fire in the
engine compartment, keep the hood closed
and contact the fire department. G
WARNING
Certain components in the engine compart-
ment, such as the engine, radiator and parts
of the exhaust system, can become very
hot. Working in the engine compartment
poses a risk of injury.
Where possible, let the engine cool down
and touch only the components described in
the following. Oil dipstick and engine oil filler neck
Only check the oil level when the engine is at
normal operating temperature. X Stop your vehicle as far away from traffic as
possible on level ground.
X Secure the vehicle to prevent it from rolling
away.
X Switch off the engine.
X Wait for five minutes.252
Engine compartment
Maintenance and care