fuel MITSUBISHI 3000GT 1991 Owners Manual

FUEL SYSTEM - On-vehicle Inspection of MPI Components13-73
INSPECTION
Using Multi-use Tester
FunctionItem No. Data displayCheck conditionCheck content
Normal stateData reading 22
Crankingl Engine cranking
Compare cranking speedIndicated speed
speedl Tachometer connectedand multi-use tester(check on and off ofto agree
reading
primary current of
ignition coil bytachometer)
NOTE(1)The tachometer indicates a third of the actual engine speed. Therefore, 3 times the tachometer indication is theactual engine speed.(2)When the tachometer is set to the 2-cylinder range, it indicates actual engine speed.
FunctionItem No. Data displayCheck conditionCoolant temperatureStandard value
Data reading22Idle speedl Engine: Running atAt -20°C (-4°F)1,300 - 1,500 rpm
idle
l Idle position switch:ONAt 0°C (32°F)At 20°C (68°F)
At 40°C (104°F)
At 80°C (176°F)1,250
- 1,450 rpm
1
,I 00 - 1,300 rpm
950-1,150rpm
600 - 800 rpm
-m-2,-5v
f-lov
---Normal waveform
Using Oscilloscope
(1) Run the engine at idle speed.
(2) Connect the probe to the oscilloscope pick-up point as
shown in the circuit diagram, and check the waveform.
1 TSB Revision

13-74FUEL SYSTEM - 0n-vehicle Inspection of MPI Components
HARNESS INSPECTION
J1@ Harness side
connector
1
7FUO496
Measure the power supply voltage.
IsvRepair the
harness.
(@I@ - Con-
trol relay)
r2
t-@ Harness side
connector
Check for continuity of the groundcbrcux.l Connector: Disconnected
7FUO497
3
‘L‘7FUO498
El3
Repair the
harness.
!?.!!ni )
Check the voltage of the output cir-cuit.l Connector: Disconnected
l lgnrtion switch: ON
Voltage
(VI4.8
- 5.2
TSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components
L
L
IGNITION SWITCH-ST
lgnitlon switch (ST)
I
Enaine control unit connector
7FUO653
Engine control unit
1 FU0638
OPERATION
lThe ignition switch-ST inputs a high signal to the engine control unit while the engine is cranking. Theengine control unit provides fuel injection control, etc., at engine startup based on this signal.
lWhen the ignition switch is set to START, the battery voltage at cranking is applied through the ignitionswitch to the engine control unit, which detects that the engine is cranking.
INSPECTION
Using Multi-use Tester
FunctionItem No. Data displayCheck conditionEngineNormal indication
Data reading18Switch stateIgnition switch: ONstopOFF
CrankingON
HARNESS INSPECTION
1
L6FU1258
2
1
Engine control
side connector
IY-6FU1259
Measure the input voltage to theengine control unit.nlEngine control unit connector:Disconnectedl Ignition switch: START
Check for continuity of the groundcircuit.
lEngine control unit connector:Disconnected
Repair the
harness.
(m - Ground)
iTSB Revision

13-76FUEL SYSTEM - On-vehicle Inspection of MPI Components
IGNITION SWITCH-ST AND INHIBITOR SWITCH
lqnition switch (ST)
@ Equipment side
connectorStarter S Control
terminalrelay
f,BL
Engine control unit connector7FUO625
Engine control unit
@ Harness side
connector
7FUO653
OPERATIONl
The ignition switch-ST inputs a high signal to the engine control unit while the engine is cranking. Theengine control unit provides fuel injection control, etc., at engine startup based on this signal.
l
When the ignition switch is set to START, the battery voltage at cranking is applied through the ignitionswitch and inhibitor switch to the engine control unit, which detects that the engine is cranking.
In case the selector lever is in a position other than the P/N range, the battery voltage is not applied to theengine control unit.
l
The inhibitor switch converts the selector lever position (whether it is at the P/N range or at others) into
high/low voltage and inputs it to the engine control unit, which then controls the idle speed control servobased on this signal.
l
The battery voltage in the engine control unit is applied through a resistor to the inhibitor switch. When the
selector lever is set to the P/N range, continuity is produced between the inhibitor switch terminal of the
engine control unit and ground through the starter motor, thereby making the terminal voltage go low.
TROUBLESHOOTING HINTS
If the inhibitor switch harness and individual part check have resulted normal but the inhibitor switch output isabnormal, poorly adjusted control cable is suspected.
TSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components13-77INSPECTION
Using Multi-use Tester
LIGNITION SWITCH-ST
FunctionItem No. Data displayCheck conditionEngineNormal rndrcation
Data reading18Switch stateIgnition switch: ON
stopOFF
CrankingONINHIBITOR SWITCH
FunctionItem No. Data displayCheck conditionSelect lever positionNormal indicationData reading 29
Shift
Ignition switch: ONP or NP or Nposition
D.2,L or RD.2.L or RHARNESS INSPECTION
@ Harness sideconnector
OlA0206
2
@ Harness srdeconnectorl
Engine control unit connector:
Connectedl
InhibItor switch connector: Dis-6a
L-J
cl3
connectedl Ignition switch: ON
Repair the
harness.Voltage
(VI@El - El)
OlA0206LII
Engine control
unit harness
side connector
Measure the power supply voltage of
the inhibitor switch.
-lEngine control unit connector:
Disconnectedl
lnhibrtor switch connector: Dis-
connectedl Ignition switch: START
Voltage
(V)
rLlltXK IlIt:Lpower supplycircuit.
Measure the inhibitor switch terminalinput voltage.
Measure the input voltage of enginecontrol unit.lEngine control unrt connector:DisconnectedlFer;it;r switch connector: Con-
1 TSB Revision

13-78FUEL SYSTEM - 0n-vehicleInspection of MPI Components
VEHICLE SPEED SENSORMIBYPM
Vehrcle speed sensor
(reed switch\)Speedometer
Terminal voltage
(V)
@ Equipment side
Vehicle speed [km/h (mph)]
162461
Engine control unit
7FUO925
Engine control unit connector7FUO653
OPERATION
lThe vehicle speed sensor which is located in the speedometer converts the vehicle speed into a pulse
signal and inputs it to the engine control unit, which then provides the idle speed control, etc. based on
this signal.
lThe vehicle speed sensor generates the vehicle speed signal by repeatedly opening and closing betweenthe voltage of about 5 V applied from the engine control unit and ground using a reed switch.
TROUBLESHOOTING HINTS
If there is an open or short circuit in the vehicle speed sensor signal circuit, the engine may stall when thevehicle is decelerated to stop.
HARNESS INSPECTION
unit harness
side connectorCheck the vehicle speed sensor out-
put circuit for continuity.
lEngine control unit connector:
Disconnected
lMove the vehicle.
TSB Revision
1
d

FUEL SYSTEM - On-vehicle lnwection of MPI ComDonents
2Measure the power supply voltage ofthe vehicle speed sensor.
@ Harness sidel Connector: Dlsconnectedl Ignition switch: ON
8)
6FU1265l Connector: Disconnected
SENSOR INSPECTIONRefer to GROUP 54
- Meters and Gauges.
TSB Revision

13-80FUEL SYSTEM - 0
n-vehicle Inspection of MPI Components
POWER STEERING OIL PRESSURE SWITCHMlOYQAA
B
$-
Engine control unit
'107
@ Harness side
connector
ml-
Power steering oil
Pressure switch
7FUO536700-2.000 1.500-2.000(100-284) (213-284)Pressure [kPa (psi)]
0, l.oIu
OPERATIONl
The power steering oil pressure switch converts presence/absence of power steering load into low/high
voltage and inputs it to the engine control unit, which then controls the idle speed control servo based on
this signal.l The battery voltage in the engine control unit is applied through a resistor to the power steering oil
pressure switch. Steering operation causes the power steering oil pressure to increase, turning the
switch on. As a result, continuity is produced between the battery voltage applied and ground. This
causes the power steering oil pressure terminal voltage to go from high to low.
TSB Revision

FUEL SYSTEM- On-vehicle Inspection of MPI Components13-81
INSPECTIONUsing Multi-use Tester
Function
Data readingItem No. Data displayCheck conditionSteering wheelNormal indication
27Switch stateEngine: IdlingSteering wheel neutralOFFposition (wheels
straight-ahead direction)
Steering wheel half turn
ON
Checking Oil Pressure
Steering wheelOil pump delivery pressure (ref. value)
Straight forward700 - 1,200 kPa (100 - 171 psi)
Turned1,500
- 2,000 kPa (213 - 284 psi)
HARNESS INSPECTION
i1
@ Harness side
connector
Measure the power supply voltage.
SENSOR INSPECTIONRefer to GROUP 37
- Service Adjustment Procedures.
TSB Revision

13-82FUEL SYSTEM - On-vehicle Inspection of MPI Components
AIR CONDITIONER SWITCH AND POWER RELAY
\
*I \\-- \
Air conditronerAir conditioner
control unitAir conditioner
compressor lock
controllerr
Engine control unit
Dual pressureswitch
M13YRAA2
b1IFF
Air conditioner
compressor
Engine control
unit connector
7FUO966
7FUO653
OPERATION
lThe air conditioner switch applies the battery voltage to the engine control unit when the air conditioner is
turned on.
lWhen the air conditioner ON signal is input, the engine control unit drives the idle speed control servo and
turns ON the power transistor. As a result, the air conditioner power relay coil is energized to turn on therelay switch, which activates the air compressor magnetic clutch.
TROUBLESHOOTING HINTS
If the air compressor magnet clutch is not activated when the air conditioner switch is turned on during idling,faulty air conditioner control system is suspected.
INSPECTION
Using Multi-use Tester
AIR CONDITIONER SWITCH
Function1 Item No. 1 Data display 1Check condition) Air conditioner switch 1 Normal indication IData reading 28
Switch stateEngine: Idling (airOFFOFFcompressor to be running
when air conditionerONONswitch is ON)\k”JTSB Revision