fuel MITSUBISHI 3000GT 1991 Service Manual

33B-20 ELECTRONIC CONTROL SUSPENSION (ECS)-llwmtk Positkm .semor I stop tight switch I POriticm DetsctionSWitEh 1 DPmping Force changeover Acluatc., / EC3 Indii.ar l.igil*
THROTTLE POSITION SENSORM33ZKA6
INSPECTION AND ADJUSTMENTIRefer to GROUP 13
- Fuel System.‘lJ ’
STOP LIGHT SWITCHM33ZCAC
To remove or mount the stop light switch, refer to GROUP 35 -
Brake Pedal.
INSPECTIONRefer to GROUP 35
- Brake Pedal.
POSITION DETECTION SWITCH and
DAMPING FORCE CHANGEOVER
ACTUATORM33ZCAD
To remove or mount the position detection switch and dampingforce changeover actuator, refer to GROUP 33A
- Strut LJAssembly and GROUP 34
- Shock Absorber Assembly.
CautionThe position detection switch and damping force
changeover actuator are built into the shock absorber
assemblies of front and rear suspensions. Since they are ofthe non-disassembly type, remove or mount them in the
form of a strut assembly or shock absorber assembly.
ECS INDICATOR LIGHTM33ZLAB
To remove or mount the ECS indicator lights, refer to GROUP54
- Meters and Gauges.
TSB Revision

42-1
BODY
CONTENTSM42AA- -
CENTER PILLAR GLASS........................................................32
CENTRAL DOOR LOCKING SYSTEM
................................55
DOOR ASSEMBLY....................................................................40
DOOR GLASS AND REGULATOR
........................................42
DOOR HANDLE AND LATCH
................................................54
DOOR TRIM AND WATERPROOF FILM
............................41
DRIP LINE WEATHERSTRIP....................................................65
ENGINE HOOD........................................................................18
FENDER*....................................................................................23
FUEL TANK FILLER DOOR
....................................................22
LIFTGATE....................................................................................20
LIFTGATE GLASS....................................................................37
LOOSE PANEL
........................................................................24
POWER WINDOW
....................................................................43
QUARTER WINDOW GLASS
................................................33SERVICE ADJUSTMENT PROCEDURES
............................
Door Adjustment................................................................Door inside Handle Play Check............................................Door Window Glass Adjustment........................................Floor Pan inspection............................................................Fuel Filler Door Adjustment................................................Hood Adjustment................................................................Liftgate Adjustment............................................................
SPECIAL TOOLS........................................................................
SPECIFICATIONS....................................................................
General Specifications........................................................Sealants and Adhesives........................................................
ServiceSpecifications........................................................
TROUBLESHOOTING............................................................
WINDOW GLASS....................................................................
WINDSHIELD............................................................................
13
14
16
14
17
14
13
13
4
2
2
3
3
5
25
28
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the
SRS or any SRS-related component.

42-14BODY - Service Rdiustment ProceduresMB990834-0118A0381
18Ac-46118A0465FUEL FILLER DOOR ADJUSTMENT
M42FDAFLoosen the fuel filler door mounting screw and adjust the fuel
filler door so that the clearance around the fuel filler door is
even without any height differences.
DOOR ADJUSTMENT
M42FEAG
1.Use the special tool to loosen the hinge mounting bolts on
the body side, and then adjust the clearance around the
door so that it is uniform on all sides.
2.If the door is not flush with the body, remove the spring pin
from the door check, use the special tool to loosen the bolts
for mounting the door hinges to the door. Move the door to
adjust the door position along the body surface.
CautionAttach protection tape to the fender edges where the
hinge is installed.
3.If the door does not open freely, adjust the engagement of
the striker with the door latch by means of the striker
mounting shim and move the striker up and down or from
side to side.DOOIR WINDOW GLASS ADJUSTMENT
M42FFAL
1. Remove the door trim and waterproof film. (Refer to
P.42-41.)2. Remove the front pillar trim.
3. Remove the drip line weatherstrip.
4. Loosen the bolts and nuts of the following parts.
l Glass guide front track
l Glass guide rear track
l Delta sash
l Stabilizer inner front
l Stabilizer inner rear
. up stop
l Door belt line outer weatherstrip
NOTEMove the window glass down to the lowest position before
removing the delta sash bolt.
1 TSB Revision-1

42-22BODY - Fuel Tank Filler Door
FUEL TANK FILLER DOOR
REMOVAL AND INSTALLATION
M42JAAS
Pre-removal and Post-installationOperationl Removal and Installation of Rear
Side Trim, Quarter Trim and Scuff Plate
(Referto GROUP 52A-Trims.)
18FOO86
18FOO69Removal steps
1. Fuel filler door
2. Fuel filler door hook
3. Release handle cover
4. Fuel filler door lock release handle
5. Fuel filler door lock release cableLA’TSB Revision