ECU MITSUBISHI 3000GT 1991 Service Manual

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-37
DABS warning light blinks once after the ignition key is turned to the “ON” position. It
Lilluminates in the “START” position and blinks once again when turned to the “ON” position.
[Explanation]
1 sec. while itharness between the ECU and the warning light, the
light illuminates only when the valve relay is off in
performs a valve relay test. If there is a break in the
the valve relay test, etc.
IGNITIONSWITCH(IG1)I
J/B
F
2
r+im
md
/
L/
COMBINATION
METER
ABS-ECU-____
KK35-KK-It3503In the ignition key “ON”
position, does voltage
between terminal No. 25 and
ground indicate battery
voltage?ABS warninglight and
Yes
Repair harness.
vMalfunction of ABS ECU
+ Replace ABS ECU.
TSB Revision

[Explanation][Hint]
The ABS ECU detects breaks in the wheel speedIn addition to a broken wire/short circuit in the wheel
sensor wire. This trouble code is output if the wheelspeed sensor, also check whether the sensor gap is
speed sensor signal is not input (or short circuited)too large, sensor harness wire is broken, or sensor
or if its output is low when starting to drive or whileharness and body connector are not properly con-
driving.
netted.E-2 When diagnosis code“15 VEH. SPD. SNSR.” is displayed
[Explanation]l Broken sensor harness
This trouble code is output when there is anl Poor connection of connector
abnormality (other than broken wire or short circuit)
NOTEin any of the wheel speed sensor output signals
(1) If contact is poor, check the sensor cable by
while driving.bending and lightly stretching it.
[Hint](2) Except for the case where a fault condition
The following can be considered as the cause of theexists in the system, but the inspection results
wheel speed sensor output abnormality.are normal; if an abnormality cannot be found in
l Distortion of rotor, teeth missingthe sensor. circuit displayed as abnormal, erase
lLow frequency noise interference when sensorthe diagnosis code and turn the ignition switch
harness wire is brokento OFF once, and then test-drive again.
l Noise interference in sensor signalIf the same trouble code is output, replace the
lSensor output signal is below the standard valueABS ECU. If the trouble does not occur any-or amplitude modulation is over the standardmore, the problem is likely to be with the ABS
ECIJ.\value. Using an oscilloscope to measure the
wave shape of the wheel speed sensor output
signal is very effective.
I\-- -.(If the trouble is in the speed sensor circuit, butdis difficult to recreate, it will recur even after the
ABS ECU has been replaced.)35-38
SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-lWhen the following diagnosis codes are displayed “11 FR SNSR. OPEN”
“12 FL SNSR. OPEN” “13 RR SNSR. OPEN” “14
RL SNSR. OPEN”
d
SPEED SENSOR
FRONTCLH) FRONTGWR!%R(LH) REARmi
m I@m @
If?All110130125ASS-ECI.+tB5
8
8I
TSB Revision

35-40SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-3When diagnosis code “21 G SNSR.” is displayed
[Explanation]
The ABS-ECU outputs this trouble code in the
following cases.
l G sensor OFF trouble (It is judged that the G
sensor continues to be OFF for more than
approximately 13 seconds except when thevehicle is stopped or when there is stop light
switch input.)
lWhen there is a broken wire or short circuit in
the harness for the G sensor system.
FUSIBLE LINK@
4
pilGGRq;
I4
Bd
pEmg=1
--a
2
__1
It
I,1II1 Ii II II II Ii II II I/ II ;/ II II II II !: II//IIII/.--A
X35-LK-R9505
I
IiNo IfIs G sensor normal? (Refer
to
P.35-92.)Replace G sensor.
I
Yes
Remove the ABS-ECU
connector and check at
the harness connector.
With the ignition key “ON”,
does the voltage between
terminal No. 6 and groundindicate battery voltage?
Repair harness.
”
ABS-ECU malfunctionIJP Replace ABS-ECU.
TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-41E-4 When diagnosis code“22 STOP LAMP SW” is displayed
ii’ [Explanation][Hint]
The ABS-ECU outputs this trouble code in theIf the stop light operates normal, the harness for the
following cases.stop light switch input circuit is broken or there is a
lStop light switch remains on for more than 15malfunction in the ABS-ECU.
minutes while the ABS is not functioning.
lThe harness wire for the stop light switch may
be open.
L
FUSIBLE,LINK@
J/B
0
I
I
ABS-ECU29
j 1 ) 2 13 14) 5 / 6 17 / 9 j 9 ~10~11~12~13(14~15(161171~9~~'9~0l21~2~3l9~~~6~~~9~~0l31l321U13l35l
KX35-AK-33306
F Check the stop light related
go out
normally?circuit and repair problem
spots.
When the brake pedal is pressed
between connector terminal No.
29 and ground indicate battery
I1 voltage! , Yes /Repair harness.
Is the voltage between No.
1terminal and ground equal to the
battery voltage when measured
wrth resistor connector discon-
nected?
YesRepair harness.
6NoIs resistor resistance 780 to
860 sl?) Replace resistor.
YesIs there continuity between No. 2
FpylReplace ABS-ECU.
visionI

35-42SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-5When diagnosis codes “41 FR SOL. VALVE”,
“42 FL SOL. VALVE” or “43 VALVE DRIFT”
are displayed.
‘LJ[Explanation]
The ABS-ECU normally monitors the solenoid valve
drive circuit.
If no current flows in the solenoid even if the ECU
turns the solenoid ON or if it continues to flow even
when turned OFF, the ECU determines thesolenoid coil wire is broken/short-circuited or the
harness is broken/short-circuited, and then these
trouble codes are output.
ABS-ECU controls the solenoid valve current and if
the current value of the solenoid valves differs from
j:
z!d
9
E6T
mA9f#;NATIOM
I-N----_---____IGNITION
SWITCH(IG2)Fw
"50
fm!EaqG-R
?,I G-RI
X35-AK-K3507each other in the same mode, solenoid valve drift
error is produced and the ABS-ECU goes into the
failsafe mode.
1No
In the resistance value forthe solenoid valve withinthe range of the standard
values?
Standard value: 1.1 - 1.3 R
Yes
”
) Replace HU.
Connect HU 1 OP connector,
\ ci;;;;;;;t EC,U connector,)
Yes
+The harness wire for the
solenoid valve circuit
whose resistance value is
outside the range of the
standard value is brokenor short circuited.
Repair harness.
1 Malfunction of ABS-ECU4 Replace ABS-ECU.I IIII1
TSB Revision

SERVICE. BRAKES -Anti-lock Braking System Troubleshooting35-43
E-6When diagnosis code “51 VALVE RELAY” is displayed
I
L[Explanation]
When the ignition switch is turned ON, the ABS
normal. In addition, normally it monitors whether or
ECU switches the valve relay OFF and ON for annot there is power in the valve power monitor line
initial check, compares the voltage of the signal tosince the valve relay is normally ON. If the supply of
the valve relay and valve power monitor line voltagepower to the valve power monitor line is inter-
to check whether the valve relay operation is
rupted, this trouble code will be output.
b
L
IGNlTIONSWITCH(IG1)
-I--
iz
=pi7TEaq
dI
6
7
Ed
COMBINATION
METER
--;Gm1 I 11
I /I
--- --
710 4Ii+
mI%
~d10 2
--- -- -?
ii3Dz62 27
iE b
1112j31a15(6/71618/10(11112113/14/15j16/17(18118~20~21~2~3~4~5~~~2@~~~0~31~2~3~~~35
KX35-AK-K3503
r-TSB I
( ;;reove;d ch; the>
4.IWhen the valve relay is checked,
are the following conditions
found?
No. 85
- No. 86: Resrstance
value 60 - 120 IINo. 30-No. 87a: Continuity
No. 30 - No. 87: No continuity
When batterv voltaoe IS aooliedbetween terminalsho. 86 and
No. 85.
No. 30
- No. 87: Contrnurty
No. 30 - No. 87a: No continurtyNo
I1-----+Valve relay malfunction
+l
IReplace valve relay.I
Yes
&I/ No1IWith the ignition key “ON”,
does the voltage between the
connector terminal No. 52 and
ground indicate battery voltage?
Yes
Connect the HU harness and
\ remove the ECU connector.
+II NnrIground Indicate battery voltage.
Replace ABS
ECIJ.
vision

35-44SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-7When diagnosis code “52 MOTOR RELAY” is displayed
[Explanation]
The ABS ECU outputs this trouble code for the
motor relay and motor in the following cases.
l When the motor relay does not function
lWhen there is trouble with the motor itself and it
does not revolve
lWhen the motor ground is disconnected and the
motor does not revolve
l When the motor continues to revolve
[Hint]
If there is motor operation noise during MUT forced
drive mode, there is a broken or short circuited
motor monitor wire.
FUSIBLE LINKa
=
::
s* m’ IL% Q7
plGizq”+-103 1
----..-___I _-
3%ECU2526L--h h
Th v-sTIII
14 ’
+---I
i”
’-ll21314 15 16 17 16 ~8~10)11~12~13~14~15~16~17~16~li1Q~0~1~~23~4~*6~2?~E~Q~30~1~2~33~~~5J
X35-AK-R3500during MUT forced drive mode?
Remove the motor relay.
I
1 ;;pa4r&&rness between 1
5Remove the motor relay and
check resistance values.
No. 85
- No. 86: Resistance
value 30 - 60 fiNo. 30 - No. 87: No continuity
Battery voltage is applied
kotw8esfn terminals No. 85 and
No. 30
- No. 87: ContinuityReplace motor relay.
1Yes
L
+I, NoIIIs pump motor ground connected
normally?Connect ground wire.
I
YesInstall motor relay and remove
HU connector.
@Vyiground indicate battery voltage?
I Yes
IConnect the HU connector
and remove the ECU connectorRepair harness.
J- No
Is resistance between bodyP Malfunction of harness
connector terminal No. 2
Lrbetween HU and ECU
and No. 26 30 - 60 a?
ItNc-11 I<
r 1 Repair harness.;~~:;$$a$?%dABS ECU malfunction
> Replace ABS ECU.
TSB Revision

SERVICE BRAKES - Set-vice Adiustment Procedures35-45lUF51F
Pedal
7\ \!4FOO7.
F14511
F14519
TSB Revision-_.1
SERVICE ADJUSTMENT PROCEDURES
BRAKE PEDAL INSPECTION AND ADJUSTMENT
1.Measure the brake pedal height as illustrated. If the’brakepedal height is not within the standard value, adjust as
follows.
Standard value (A): 177
- 182 mm (7.0 - 7.2 in.)
(I) Disconnect the stop light switch connector, loosen the
lock nut, and move the stop light switch to a position
where it does not contact the brake pedal arm.
(2) Adjust the brake pedal height by turning the operating
rod with pliers (with the operating. rod lock nut
loosened), until the correct brake pedal height is
obtained.
(3) After screwing in the stop light switch until it contacts
the brake pedal stopper (just before the brake pedal is
caused to move), return the stop light switch
l/2 to 1
turn and secure by tightening the lock nut.
(4) Connect the connector of the stop light switch.
(5) Check to be sure that the stop light is not illuminated
with the brake pedal unpressed.
Reference value (6): 0.5
- 1.0 mm (.02 - .04 in.)
2. On vehicles with automatic transaxle, check the shift-lock
mechanism. (Refer to GROUP 23
- Transaxle Control.)
3. With the engine stopped, depress the brake pedal two or
three times. After eliminating the vacuum in the power
brake booster, press the pedal down by hand, and confirm
that the amount of movement before resistance is met (the
free play) is within the standard value range.
Standard value (C): 3
- 8 mm (.I - .3 in.)
If the free play is less than the standard value, confirm that
the clearance between the stop light switch and brake
pedal is within the standard value.
If the free play exceeds the standard value, it is probably
due to excessive play between the clevis pin and brake
pedal arm. Check for excessive clearance and replace faulty
parts as required.
4.Start the engine, depress the brake pedal with approximate-
ly 500 N (110
Ibs.) of force, and measure the clearance
between the brake pedal and the floorboard.
Standard value (D): 80 mm (3.1 in.) or more
If the clearance is less than the standard value, check for air
trapped in the brake line and for brake fluid leaks. If
necessary, check the brake system mechanism (excessive
shoe clearance due to faulty auto adjuster) and repair faulty
parts as required.~1~1
I
I
I
I
I

35-52SERVICE BRAKES - Service Adjustment Procedures
14FOO94
k.!! I14FOO427. Using the following procedure, check the brake drag
torque.@ Start the engine and depress and hold the brake pedal
’for five seconds. [Approx. 200 N (44
Ibs.)]@ Stop the engine.@ Rotate the brake disc ten turns in the forward direction.@ Using a spring balance, check the brake drag force.
8. If the difference between the brake drag force and hub
rotating force exceeds the standard value, disassemble the
piston and check the piston sliding surfaces for dirt and
rust, piston seal for deterioration, and lock pin and guide pin
for sliding motion.
Standard value: 70 N (15.4
Ibs.) [4 Nm (3 ft.lbs.)] or less
INSPECTION OF FRONT BRAKE DISC THICKNESS1. Remove dirt and rust off the surface of the brake disc.
2.Measure the thickness of disc at four or more places of the
pad contacting surface.
Standard value:
24.0 mm (.94 in.)
30.0 mm (1.18 in.)
,Limit:
22.4 mm (.88 in.)
28.4 mm (1.12 in.)
3.If the wear exceeds the limit even at one place, replace the
right and left discs and brake pads as a set.
FRONT BRAKE DISC RUN-OUT CHECKM35FSAF
1. Remove the front brake assembly; and support it with a
wire, etc.
TSB Revision2. Place a dial gauge approximately 5 mm
(.2 in.) from the
outer circumference of the brake disc, and measure the
run-out of the disc.
Limit: 0.10 mm (.004 in.) or less
NOTESecure the disc to the hub with wheel nuts.

SERVICE BRAKES - Service Adjustment Procedures
4. Remove the following parts from caliper support.@ Outer shim@ Pad assembly@ Pad & wear indicator assembly@ Clip@ Inner shim A@ Inner shim B
d
14N0031
f\
/0014N013714A040;14N003:
14AO401
l%FLision
14N01365. Measure hub torque with pad removed to measure brake
drag torque after pad installation.
On vehicles with VCU-equipped LSD, disengage the drive
shaft and companion flange.
NOTESecure the disc to the hub with wheel nuts.
6. Securely attach the pad clip to the caliper support.
Caution
Do not deposit
&ease or other dirt on pad or brake disc
friction surfaces.
7.Clean the piston and then push the piston into the cylinder.
8.With care not to allow the piston boot to be wedged, lower
the caliper assembly and fit the lock pin.
9. Check brake drag torque as follows.
(I) Start engine and hold brake pedal down for 5 seconds.
[Approx. 200 N (44
Ibs.)](2) Stop engine.
(3) Turn brake disc forward
10 times.
(4) Check brake drag torque with spring scale.
If the difference between brake drag torque and hub torque
exceeds the standard value, disassemble piston and clean
piston. Check for corrosion or worn piston seal, andcheck
the sliding condition of the lock pin sleeve and guide
pinl/jsleeve.
Standard value: 70 N (15.4
Ibs,,) [4 Nm (3 ft.lbs.)] or less