key battery MITSUBISHI 3000GT 1991 User Guide

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-33
1i, 1 CheckABSECU. ,
Remove the ECU connector and
check.Does the voltage between ECU harness
> Broken wire between ABSj Repair harness.
connector terminal No. 25 and ground
warning light and ECU
indicate battery voltage while the
ignition key is in the “ON” position?
Yes
> ABS ECU malfunction> Replace ABS ECU.
Remove valve relay and check.
I
1Nois valve relay normal? (Refer to
P.35-62.)) Valve relay malfunction+ Replace valve relay.IYes
Install the valve relay, remove the HU
connector and check.
Does voltage between the HU harness
uLEm-h[ Repair harness.
connector terminal No. 8 and ground
indicate battery voltage
while the
ignition key is in the “ON” position?
Yes
r7; t%$~?$!Je~~~g~undIIs there continuity between HU harness9 Repair harness.
connector terminal No. 9 and ground?
Is there continuity between HU harness
connector terminals No. 8 and No. 9?Yes+ HU malfunctionI+ Replace HU.
b Connector not connected
securely.- Replace connector.
1 TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
35-35
IGNITIONSWITCH(IG2)
R&RRELAY
DIODE
KX35-AK-R35028PREVIOUS PAGE
With the ignition key in the
“ON” position, does voltage
between ECU connector
terminal No. 18 and ground
indicate the battery voltage?
Is there continuity between
body harness terminals No. 9
and No. 34, and ground?
Repair harness.
vNoIs there continuity between-body harness connector ter-diagnosis inspection
minals No. 23 and No. 24,terminal and ABS ECU
and diagnosis inspection ter-
minals No. 4 & No. 1 O?Yes
”Malfunction of ABS ECU
Replace ABS ECU.
TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-37
DABS warning light blinks once after the ignition key is turned to the “ON” position. It
Lilluminates in the “START” position and blinks once again when turned to the “ON” position.
[Explanation]
1 sec. while itharness between the ECU and the warning light, the
light illuminates only when the valve relay is off in
performs a valve relay test. If there is a break in the
the valve relay test, etc.
IGNITIONSWITCH(IG1)I
J/B
F
2
r+im
md
/
L/
COMBINATION
METER
ABS-ECU-____
KK35-KK-It3503In the ignition key “ON”
position, does voltage
between terminal No. 25 and
ground indicate battery
voltage?ABS warninglight and
Yes
Repair harness.
vMalfunction of ABS ECU
+ Replace ABS ECU.
TSB Revision

35-40SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-3When diagnosis code “21 G SNSR.” is displayed
[Explanation]
The ABS-ECU outputs this trouble code in the
following cases.
l G sensor OFF trouble (It is judged that the G
sensor continues to be OFF for more than
approximately 13 seconds except when thevehicle is stopped or when there is stop light
switch input.)
lWhen there is a broken wire or short circuit in
the harness for the G sensor system.
FUSIBLE LINK@
4
pilGGRq;
I4
Bd
pEmg=1
--a
2
__1
It
I,1II1 Ii II II II Ii II II I/ II ;/ II II II II !: II//IIII/.--A
X35-LK-R9505
I
IiNo IfIs G sensor normal? (Refer
to
P.35-92.)Replace G sensor.
I
Yes
Remove the ABS-ECU
connector and check at
the harness connector.
With the ignition key “ON”,
does the voltage between
terminal No. 6 and groundindicate battery voltage?
Repair harness.
”
ABS-ECU malfunctionIJP Replace ABS-ECU.
TSB Revision

SERVICE. BRAKES -Anti-lock Braking System Troubleshooting35-43
E-6When diagnosis code “51 VALVE RELAY” is displayed
I
L[Explanation]
When the ignition switch is turned ON, the ABS
normal. In addition, normally it monitors whether or
ECU switches the valve relay OFF and ON for annot there is power in the valve power monitor line
initial check, compares the voltage of the signal tosince the valve relay is normally ON. If the supply of
the valve relay and valve power monitor line voltagepower to the valve power monitor line is inter-
to check whether the valve relay operation is
rupted, this trouble code will be output.
b
L
IGNlTIONSWITCH(IG1)
-I--
iz
=pi7TEaq
dI
6
7
Ed
COMBINATION
METER
--;Gm1 I 11
I /I
--- --
710 4Ii+
mI%
~d10 2
--- -- -?
ii3Dz62 27
iE b
1112j31a15(6/71618/10(11112113/14/15j16/17(18118~20~21~2~3~4~5~~~2@~~~0~31~2~3~~~35
KX35-AK-K3503
r-TSB I
( ;;reove;d ch; the>
4.IWhen the valve relay is checked,
are the following conditions
found?
No. 85
- No. 86: Resrstance
value 60 - 120 IINo. 30-No. 87a: Continuity
No. 30 - No. 87: No continuity
When batterv voltaoe IS aooliedbetween terminalsho. 86 and
No. 85.
No. 30
- No. 87: Contrnurty
No. 30 - No. 87a: No continurtyNo
I1-----+Valve relay malfunction
+l
IReplace valve relay.I
Yes
&I/ No1IWith the ignition key “ON”,
does the voltage between the
connector terminal No. 52 and
ground indicate battery voltage?
Yes
Connect the HU harness and
\ remove the ECU connector.
+II NnrIground Indicate battery voltage.
Replace ABS
ECIJ.
vision

42-56BODY - Central Door Locking System
CHECKING INDIVIDUAL PART AND CIRCUIT (IGNITION KEY REMINDER SYSTEM)
1. ETACS POWER-SUPPLY AND GROUND CIRCUITS
L-
Batterv
$1,\ .
\I \/ \I
‘/1,\/2-“1
m+,2T.,l\ ,.c.i -
151
Junction block (Multi-purpose fuse)
Jumper connector
ETACS unit(ECU)
“I : Vehicles without theft-alarm system
“2: Vehicles with theft-alarm systemz1116FO314Description of operation
The battery supplies a stabilized 5V power supply to the electronic control unit, via the constant-voltage circuit
and terminal (51) directly connected to the battery. If there is an abnormal condition of the power-supply
circuit, other ETACS functions also will not operate.
Electronic control unit terminal voltage (Connection status of electronic control unit connector)
ECU terminal No. Signal
StatusTerminalvoltage
I
51Electronic control unit power supply
At all timesSystem
voltage
IChecking the ground circuit (Disconnect the connector and check the wiring harness side.)
IIII1Terminal No.Connected to/measured part
MeasurementTesterconnectionCheck conditionsStandard57”’
Electronic control unit ground
Resistance57*‘-groundAt all timesContinuity
59”)59*2-ground
NOTE
“I : Vehicles without theft-alarm system.“2: Vehicles with theft-alarm system
TSB Revision

INTERIOR - Troubleshooting52A-7OPERATION
Key-reminder warning
L0 Battery voltage is always supplied, through
fusible link No. 6 to the key-reminder switch.
l When the driver’s seat is opened while the
ignition key is still in the key cylinder, the door
switch is switched ON, electricity flows to
fusible link No. 6, the key-reminder switch, the
buzzer, the door switch, and ground, and the
buzzer sounds.
Seat belt warning
lBattery voltage is applied, through fuse No. 11
to the ETACS unit when the ignition key is at the
“ON” position.
l Electricity flows to fusible link No. 6, the seat
belt warning light, the ETACS unit, and ground,
and the seat belt warning light flashes for
approx. 6 seconds.
lIf the driver does not buckle the seat belt, the
seat belt switch is switched ON, electricity
flows to fusible link No. 6, the key-reminder
switch, the buzzer, the seat belt switch, the
ETACS unit, and ground, and the buzzer sounds
for approx. 6 seconds.
lWhen the driver buckles the seat belt, the seat
belt switch is switched OFF and the buzzer
stops.
COMPONENT LOCATION
Name1 Symbol (
ETACS unitIA t19FO134TROUBLESHOOTING HINTS
Key-reminder warning
The key-reminder warning doesn’t sound.
(I) The seat belt warning function is OK.
l Check the door switch.
(2) The seat belt warning also doesn’t function.
l Check the buzzer.
Seat belt warning
1. The seat belt warning doesn’t function.
(I) The seat belt warning light flashes.
l Check the seat belt switch.
(2) The seat belt warning light also does not
function (and the key-reminder warning also
does not function).
l Check the key-reminder switch.
2. The buzzer doesn’t stop even though the driv-
er’s seat belt has been buckled.
l Check the seat belt switch.
3. The seat belt warning light doesn’t flashes (but
the buzzer sounds).
l Check the light bulb.
NOTEFor the inspection of the ETACS unit, refer to
P.52A-25.16FO35
1 TSB Revision

SUPPLEMENTAL RESfRAlNT SYSTEM (SRS) - Troub!eshooting 52B-17TROUBLESHOOTING
M52ECAA
idSRS DIAGNOSTIC PROCEDURES
- INITIAL STEPS’FOLLOW THESE STEPS WHEN BEGINNING ANY SRS SERVICE:
/II/ ,- -u’ 16FO304
SRS warning light
Multi-use fester
(MB991341)RbM pack(MB991359)
Diagnosis/
service data
output
Ground
16LOO9
[TSB
1. Check the SRS fuses (multi-purpose fuses No. 11 and No.
18).If either is loose, tighten it; if damaged or blown, replace it.
.
2.After performing step 1, start engine. Does “SRS” warning
light
illumi.nate for about 7 seconds and then turn OFF? If
yes, SRS system is functioning properly.
If no, continue with following steps.
NOTEIf the battery power supply (multi-purpose fuses No. 11 or
No. 18) is disconnected with the ignition key in the “ON”
position, the SRS warning light will continue to illuminate
even after the fuses are replaced in their original positions.
In this case, the SRS warning light can be extinguished by
turning the ignition switch ON and OFF
10 times.
3. Turn the ignition key to the “LOCK” position.
4. Insert ROM pack into the Multi-use Tester and connect
tester to Diagnosis Check Connector in glove compart-
ment.
5. Start the SRS diagnosis,by conducting TEST 1
(SRSwarninq liqht does not extinguish) or TEST 2 (SRS warning
light does- not illuminate.) which begins on next page or
page
[52B-191.
ivision

52B-20 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - Troubleshooting
SELF-DIAGNOSIS QUICK REFERENCE CHART
Fault
No.
-
11
32
Diagnosis code name
[Failure mode]
(NORMAL)
G-SENS. TRBL
1[Short circuit]
G-SENS. TRBL 2[One open-circuit]
G-SENS. TRBL 3[Two open-circuit]
SQUIB TRBL 1[Short circuit]
SQUIB TRBL 2
[Open-circuit]
CONDENS. VO. HI
CONDENS. VO. LO
CRANKING TRBL
CONN. UNLOCKED
Explanation
Normal. The SRS is in goodorder.
The circuits for the front impact sensor are shortedto each other.
Right or left impact sensor cirucit is open or the
wire from the sensor to the SDU is open-circuit.
Right and left impact sensor circuits are open or thewires from the sensors to the SDU areopen-circuit.
The circuits for the air bag module (squib) are
shorted to each other or the circuit isgrounded.
The air bag module Isquib) circuit is open or the wire
from the air bag to the SDU (clock spring) is open-circuit.
The capacitor (integrated in the
SDU) terminal voltage
is higher than the specified value for 5 seconds.
The capacitor (integrated in the
SDU) terminal voltage
is lower than the specified value for 5 seconds.
The circuit for the cranking signal is shorted to
some power supply circuits.
It takes at least 45 seconds that the SDU detects
this fault.
The lock switch (short bar) of the SDU double lockconnector isopen.Service
Perform TEST 5
Perform TEST 6(I) Turn the ignition key
to the “LOCK” posi-
tion, disconnect the
negative battery
cable and tape the
terminal.
(2) After waiting atleast 30 seconds,
replace the SDU.
(Refer to P.52B-59.)
Perform TEST 7
Perform TEST 8NOTE
- IMPORTANT
(1) After repairing the SRS, reconnect the battery cable, erase the diagnosis code memory from theMulti-use Tester and check the SRS warning light operation to verify the system functions
properly. (Refer to TEST 1.)
(2) SDU
= SRS Diagnosis Unit
1 TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - Troubleshooting 52B-21
/
id
FaultDiagnosis code nameNo.[Failure mode]Explanation
Service
41
IG VOLT LOW 1The multi-purpose fuse (No. 18) is blown or the wirefrom the fuse to the SDU is open-circuit or itsresistance value is increased.
It takes at least 5 seconds that the SDU detects
this fault.
Perform TEST 9
42
IG VOLT LOW 2The multi-purpose fuse (No. 11) is blown or the wirefrom the fuse to the SDU is open-circuit or itsresistance value is increased.
It takes at least 5 seconds that the SDU detects
this fault.
Perform TEST 10
SRS LMP TRBL 1
i
The SRS warning light circuits are open or the wireWhen SRS warning lightOpen circuit orfrom the light to the SDU is grounded.does not extinguish:43ground shortIIt takes at least 5 seconds with the light OFF thatPerform TEST 11the SDU detects this fault.When SRS warning light
does not illuminate:
Perform TEST 12
SRS LMP TRBL 2The SRS warning light drive transistor (integrated
(1) Turn the ignition key
44SRS warning light
[I
in the SDU) is open-circuit.to the “LOCK” posi-
drive transistortion, disconnet the
is open-circuitnegative battery
cable and tape the
SRS DIAG. UNITThe EEP ROM or A/D converter (integrated in the SDU)terminal.is defective.(2) After waiting at
45least 30 seconds,
replace the SDU.
(Refer to P.52B-59.)
/NOTE -IMPORTANT
b(1) After repairing the SRS, reconnect the battery cable, erase the diagnosis code memory from theMulti-use Tester and check the SRS warning light operation to verify the system functions
properly. (Refer to TEST 1.)
(2) SDU
= SRS Diagnosis Unit
1 TSB Revision