key MITSUBISHI 3000GT 1991 Workshop Manual

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
35-35
IGNITIONSWITCH(IG2)
R&RRELAY
DIODE
KX35-AK-R35028PREVIOUS PAGE
With the ignition key in the
“ON” position, does voltage
between ECU connector
terminal No. 18 and ground
indicate the battery voltage?
Is there continuity between
body harness terminals No. 9
and No. 34, and ground?
Repair harness.
vNoIs there continuity between-body harness connector ter-diagnosis inspection
minals No. 23 and No. 24,terminal and ABS ECU
and diagnosis inspection ter-
minals No. 4 & No. 1 O?Yes
”Malfunction of ABS ECU
Replace ABS ECU.
TSB Revision

35-36\
SERVICE BRAKES -‘\Anti-lock Braking System Troubleshooting
CABS warning light does not illuminate when the ignition key is in the “START” position.
[Explanation]
The ABS ECU uses the
IG2 power source which is
turned off in the “START” position. The ABS
warning light uses the
IG, power source which is
not turned off even in the “START” position.
Consequently, in the “START” position, power is off
LJand the ECU turns the valve relay OFF. If the
warning light does not illuminate at this time, there
is trouble in the warning light circuit on the valve
relay side.
EfiE-
9B
wIGNSW1--
J/BF
COMBINATIONMETER
G-R 11 G-
IN;IGl)
ITSB IRemove the hydraulic
unit (HU) connector andcheck.
Yes
c-No -Is there continuity between-> Broken line between HUbody connector terminal No. 9
and body ground
and ground?
-No 7Is there continuity between> Valve relay malfunction orHU connector terminal No. 8
break in HU harness wire
and terminal No. 9?
YesYes
&
Replace valve relay.I
1
HU harness malfunctionj Replace HU.
NOTEWhen performing the check marked *, note polarity of the diode
(refer to the circuit diagram).
visionI

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-37
DABS warning light blinks once after the ignition key is turned to the “ON” position. It
Lilluminates in the “START” position and blinks once again when turned to the “ON” position.
[Explanation]
1 sec. while itharness between the ECU and the warning light, the
light illuminates only when the valve relay is off in
performs a valve relay test. If there is a break in the
the valve relay test, etc.
IGNITIONSWITCH(IG1)I
J/B
F
2
r+im
md
/
L/
COMBINATION
METER
ABS-ECU-____
KK35-KK-It3503In the ignition key “ON”
position, does voltage
between terminal No. 25 and
ground indicate battery
voltage?ABS warninglight and
Yes
Repair harness.
vMalfunction of ABS ECU
+ Replace ABS ECU.
TSB Revision

35-40SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-3When diagnosis code “21 G SNSR.” is displayed
[Explanation]
The ABS-ECU outputs this trouble code in the
following cases.
l G sensor OFF trouble (It is judged that the G
sensor continues to be OFF for more than
approximately 13 seconds except when thevehicle is stopped or when there is stop light
switch input.)
lWhen there is a broken wire or short circuit in
the harness for the G sensor system.
FUSIBLE LINK@
4
pilGGRq;
I4
Bd
pEmg=1
--a
2
__1
It
I,1II1 Ii II II II Ii II II I/ II ;/ II II II II !: II//IIII/.--A
X35-LK-R9505
I
IiNo IfIs G sensor normal? (Refer
to
P.35-92.)Replace G sensor.
I
Yes
Remove the ABS-ECU
connector and check at
the harness connector.
With the ignition key “ON”,
does the voltage between
terminal No. 6 and groundindicate battery voltage?
Repair harness.
”
ABS-ECU malfunctionIJP Replace ABS-ECU.
TSB Revision

SERVICE. BRAKES -Anti-lock Braking System Troubleshooting35-43
E-6When diagnosis code “51 VALVE RELAY” is displayed
I
L[Explanation]
When the ignition switch is turned ON, the ABS
normal. In addition, normally it monitors whether or
ECU switches the valve relay OFF and ON for annot there is power in the valve power monitor line
initial check, compares the voltage of the signal tosince the valve relay is normally ON. If the supply of
the valve relay and valve power monitor line voltagepower to the valve power monitor line is inter-
to check whether the valve relay operation is
rupted, this trouble code will be output.
b
L
IGNlTIONSWITCH(IG1)
-I--
iz
=pi7TEaq
dI
6
7
Ed
COMBINATION
METER
--;Gm1 I 11
I /I
--- --
710 4Ii+
mI%
~d10 2
--- -- -?
ii3Dz62 27
iE b
1112j31a15(6/71618/10(11112113/14/15j16/17(18118~20~21~2~3~4~5~~~2@~~~0~31~2~3~~~35
KX35-AK-K3503
r-TSB I
( ;;reove;d ch; the>
4.IWhen the valve relay is checked,
are the following conditions
found?
No. 85
- No. 86: Resrstance
value 60 - 120 IINo. 30-No. 87a: Continuity
No. 30 - No. 87: No continuity
When batterv voltaoe IS aooliedbetween terminalsho. 86 and
No. 85.
No. 30
- No. 87: Contrnurty
No. 30 - No. 87a: No continurtyNo
I1-----+Valve relay malfunction
+l
IReplace valve relay.I
Yes
&I/ No1IWith the ignition key “ON”,
does the voltage between the
connector terminal No. 52 and
ground indicate battery voltage?
Yes
Connect the HU harness and
\ remove the ECU connector.
+II NnrIground Indicate battery voltage.
Replace ABS
ECIJ.
vision

STEERING - Steering Wheel and Shaft37A-13
STEERING WHEEL AND SHAFTM37GA- -
L
REMOVAL AND INSTALLATION
Post-installation Operation
l Checking of Steering Wheel Positlonwith Wheels Straight Ahead
\5Nm
4 ft.lbs.I7
12 Nn8ft.lb
\1
40 Nm
29 ftlbs.
i
13FOO35Removal steps
/
L
Mb1. Air bag module*I) l a2. Steering wheel
3. Lower column cover;: E;feTn switch assembly
4. Upper column cover9. Key interlock cable
I
(Refer to GROUP 23 -
5. Knee protectorIO. Slide leverTransaxle Control.)
(Refer to GROUP
52A- Instrument Panel.)11. Steering column assembly
6. Lap cooler duct and foot shower duct12. Column support assemblyTSB Revision

42-12
BODY - Troubleshooting
OPERATIONl When the door lock switch is set to the LOCK side (or
UNLOCK side), the LOCK side (or UNLOCK side) of the
door lock relay is turned ON and the door actuators of
alIsadoors operate.
lIf the driver seat side door (or assistant seat side door) is
opened and the driver seat side inside lock knob (or
assistant seat side inside lock knob) is locked with the key
inserted in the ignition switch, the ETACS unit grounds the
unlock side circuit of the door lock relay to unlock all doors.
This way, failure to remove the key is prevented.
NOTEThe door lock actuator contains a PTC thermister to prevent
damage caused by overheating of the motor. If the central
door lock is frequently used, the actuator may temporarily
fail to operate. If it returns to normal in a few minutes, it is
not defective.
TROUBLESHOOTING HINTS
1. One of the door lock actuators fails to operate.
l Check the door actuator which fails to operate.
2. The ignition key reminder system does not function.
l For information concerning ETACS control, refer to
P.42-55.

42-54
BODY - Door Handle and Latch
DOOR HANDLE AND LATCHM42MDCAREMOVAL AND INSTALLATION
18FOO42
I11.I
I18FOO41
Pre-removal and Post-installationlWO202
Door inside handle removal
Door Inside Handle Play Check (Refer to
P.42-16.)1. Door inside handle
Door outside handle and latch removal steps
2. Door key cylinder unlock switch connector
(Vehicles with theft-alarm system)
3. Door outside handle
4. Ring
5. Door lock key cylinder
6. Door latch assembly
INSPECTION
DOOR KEY CYLINDER UNLOCK SWITCH
The key cylinder unlock switch is normal if there is not
continuity between terminals 1 and 2 when the key is turned
approx. 20” clockwise or counterclockwise from the neutral
position, and there is continuity when it is turned further.
TSB Revision

BODY - Central Door Locking System42-55
Ground ETACS
,611338Nith voltmeterCENTRAL DOOR LOCKING SYSTEM M42ZDAJ
IGNITION KEY REMINDER TROUBLESHOOTING
GUIDE
INPUT CHECK
Using the multi-use tester or voltmeter, check whether or not
the input signals from each switch are being input to the
ETACS unit.
(1) Connect the multi-use tester to the diagnosis check
connector located at the right side of the junction block or
connect the voltmeter between the ETACS terminal and
the ground terminal.
(2) Check if the buzzer of the multi-use tester sounds or the
needle of the voltmeter moves when each switch noted
below is operated.
If the buzzer sounds or the needle moves,. the input signals
are being input to the ETACS unit, so that switch can be
considered to be functioning normally. If not, the switch or
switch input circuit is faulty. Check the switch and the
switch input circuit.
l Door lock actuator
l Door switch
l Key reminder switch
IGNITION KEY REMINDER TROUBLESHOOTING QUICK-REFERENCE TABLE
CENTRAL DOOR LOCKING SYSTEM
Problem
No unlock operation can be made by
pressing door lock knob after
fulfil-ment of following conditions.
l Insertion of key in ignition switch
(key reminder switch OFF)
l Opening of door(door switch ON)Probable causeCheck methodRemedy
Key reminder switchIf found defective afterCorrect harness or
input circuit shortedinput check, check circuit
bench test No. 4
rep:a~~~ key reminder
Key reminder
(P.42-59).switch shorted
Door switch inputIf found defective afterCorrect harness or
circuit brokeninput check, check circuit
replace door switch
bench test No. 5
Breaks in door switch
(P.42-60).Faulty electronic
-Replace the electronic
control unitcontrol unit
NOTE“ECU” (Electronic Control Unit) indicates the ETACS unit
1 TSB Revision

42-56BODY - Central Door Locking System
CHECKING INDIVIDUAL PART AND CIRCUIT (IGNITION KEY REMINDER SYSTEM)
1. ETACS POWER-SUPPLY AND GROUND CIRCUITS
L-
Batterv
$1,\ .
\I \/ \I
‘/1,\/2-“1
m+,2T.,l\ ,.c.i -
151
Junction block (Multi-purpose fuse)
Jumper connector
ETACS unit(ECU)
“I : Vehicles without theft-alarm system
“2: Vehicles with theft-alarm systemz1116FO314Description of operation
The battery supplies a stabilized 5V power supply to the electronic control unit, via the constant-voltage circuit
and terminal (51) directly connected to the battery. If there is an abnormal condition of the power-supply
circuit, other ETACS functions also will not operate.
Electronic control unit terminal voltage (Connection status of electronic control unit connector)
ECU terminal No. Signal
StatusTerminalvoltage
I
51Electronic control unit power supply
At all timesSystem
voltage
IChecking the ground circuit (Disconnect the connector and check the wiring harness side.)
IIII1Terminal No.Connected to/measured part
MeasurementTesterconnectionCheck conditionsStandard57”’
Electronic control unit ground
Resistance57*‘-groundAt all timesContinuity
59”)59*2-ground
NOTE
“I : Vehicles without theft-alarm system.“2: Vehicles with theft-alarm system
TSB Revision