key MITSUBISHI 3000GT 1991 Workshop Manual

BODY - Central Door Locking System42-57
2. DOOR LOCK ACTUATOR INPUT CIRCUIT
L
ETACS
unit (ECU)
Fusible link @
Junction block
(Multi-purpose fuse)
r7‘?r p O.BBBI
“1 : Vehicles without theft-alarm system
“2: Vehicles with theft-alarm systemU-U16(RI-U16FO316
‘IL/Description of operation
If the door is opened with the ignition key inserted and then locking is made by means of inside lock knob, the
door lock actuator is brought to the OFF position, sending H signal to the electronic control unit.
This signal operates the timer. circuit of the electronic control unit and the driving circuit operates to actuator
all the door lock actuators.
Electronic control unit terminal voltage (Connection status of electronic control unit connector)
ECU terminal No. Signal
ConditionTerminal
voltage
ll”,13”’ (LH)Door lock actuator switchDoor lock actuator switchsignalLock (OFF)5v
12”‘. 14”:’ (RH)Unlock (ON)ov
Door lock actuator switch circuit test (Disconnect the connector of the electronic control unit and
check the wiring harness side.)
ECU TerminalConnected to/No.measured partMeasurementTester
connectionCheck conditionsStandard
Door lock actuator
ll*‘, 13”’ (LH) switch signalResistance11 *‘-groundDoor lockLock (OFF)12*‘-groundactuator switchNo continuity
12”‘. 14”’ (RH)13*:-ground14*‘-groundUnlock (ON) Continuity
NOTE*1 : Vehicles without theft-alarm system
“2: Vehicles with theft-alarm systemChecking the individual part
Door lock actuator: Refer to
P.42-62.
1 TSB Revision

42-58BODY - Central Door Locking SystemI3. DOOR LOCK POWER RELAY ACTIVATION CIRCUIT
Fusible link 0
“I : Vehicles without theft-alarm system“2: Vehicles with theft-alarm system
Door lockactuator:
(LH)
‘d
Door lockactuator(RH)16FO329’Description of operation
If the door is opened with the ignition key inserted and then door locking is made, transistor Tr of the
electronic control unit is turned ON to operate the door lock power relay (unlock side) and the door lock
actuator is unlocked.
NOTEBefore locking the front seat passenger door, make sure that the driver door lock actuator is in the LOCK
position. If the driver door lock actuator is in the UNLOCK position, the front passenger door lock actuator
does not operate.
Electronic control unit terminal voltage (Connection status of electronic control unit connector)
ECU terminal No. Signal
ConditionTerminalvoltage
1XI, 3”’Door lock power relaySystem(unlock side) signalAt all times (except when door unlock isin operation)voltage
NOTE“I : Vehicles without theft-alarm system
“2: Vehicles with theft-alarm system
Checking the individual part
Door lock power relay: Refer to
P.42-63.
LJ
TSB Revision

BODY - Central Door Locking System
4. KEY REMINDER SWITCH INPUT CIRCUIT42-59

Fusiblelink@
ETACSunit(ECU)
16FO319
Junction block
(Multi-purpose fuse)
Key reminder
switch
ETACSunit(ECU)
16FO318
bDescription of operation
Insert the key in the ignition key cylinder, and the key reminder switch will be turned OFF, sending H signal to
the electronic control unit. Pulling the key out of the cylinder will turn on the key reminder switch, sending L
signal to the electronic control unit.
If there is any abnormality in the key reminder switch input circuit, abnormal key reminder buzzer will result.
Electronic control unit terminal voltage (Connection status of electronic control unit connector)
ECU terminal No. Signal
ConditionTerminal
voltage60”’
Key reminder switch signalKey is pulled outov
64”’
Key is inserted5v
Checking the key reminder switch circuit (Disconnect the connector of the electronic control unit and
check the wiring harness side.)
Terminal No.Connected to/measured partMeasurementTesterconnectionCheck conditronsStandard60”’
Key reminder swatchResistance60*‘-groundKey is pulled outContinuity
Key is insertedNo continuity
NOTE“I : Vehicles without theft-alarm system*2: Vehicles with theft-alarm system
/Checking the individual part
’Key reminder switch: Refer to GROUP 54 - Ignition Switch.
TSB Revision

EXTERIOR - Troubleshooting
i.l
L
ELECTRIC REMOTE CONTROLLED MIRRORMSlEBBFCIRCUIT DIAGRAM
BEI
LLIfs
9LF?
PWATED
1
@iOA
w&
:ERIGNITIONSWITCH(ACC)-I
d
4
J/B
@ ::::15A
9
C-82
m
$i$iiq
:I1I’II
,IIIIIIII
IttI
1II,I
IIII
IIIt,
---------------------2 2
f
D-42
'-14
7
83296m9
-?;'9:c:a > c3> u,
REMOTEfjI#;"o;LLE'
EFti
tIL-------------q+1~-I~---------------------)L13w
.D-43 ‘1'8--- ---- ------------------ +’'7at2 D-41
/liRmqtI.) El::
:
1
(LH)(RH)
REMOTEiy;;I$)LLED:l:VEHICLES WITH MIRROR HEATERKXS-AC-R13C3-NYX2:VEHICLES WITHOUT MIRROR HEATEFOPERATION
l When the remote controlled mirror switch is
operated while the ignition key is in “ACC” or
“ON” position, current flows through fuse No.@ remote controlled mirror switch, remote
controlled mirror,remote controlled mirror
switch, and ground, causing the mirror to move.TROUBLESHOOTING HINTS
Neither right nor left mirror operates
1) Also cigarette lighter does not operate
l Check multi-purpose fuse No.
0.2) Cigarette lighter operates
l Check remote controlled mirror switch.
TSB Revision

51-10EXTERIOR - Service Adjustment Procedures
68FOO51
Multl-use tester
,SERVICE ADJUSTMENT PROCEDURES
INSPECTION OF ACTIVE AERO SYSTEM
1. INSPECTION BY WARNING LIGHT
d!Turn the ignition switch from “OFF” to “ON” to see if the
warning light is lit for approx. three seconds and then goes
out. If not, replace the control unit.
NOTE
(1) The active aero control unit has a self-check function
which is designed as follows: Turn the ignition switch
from “OFF” to “ON”. If the unit is in normal condition,
the warning light is lit for approx. three seconds and
then goes out.
(2) If the front venturi skirt does not return to the standard
condition properly in normal use, the warning light
comes on
2. INSPECTION BY ACTIVE AERO SWITCH AT AUTO 2
(1) With the vehicle stopped, insert the key in the ignition
key cylinder.
(2) Set the active aero switch to AUTO 2 to make sure that
the active aero system is placed in the operative
condition and the indicator light comes on. Then turn off
the active aero switch to confirm that the system
LCJreturns to the standard condition and the indicator light
goes out.
(3) If there is abnormality, check the following parts.
l Active aero switch
l Lighting monitor switch
l Air dam link assembly and rear spoiler
l Wiring harness
3. INSPECTION WITH MULTI-USE TESTER
Using pseudo vehicle speed input function of the multi-use
tester, inspection can be made by means of vehicle speed.
(1) Set the multi-use tester to the diagnosis connector.
(2) Turn the ignition switch to “ACC” or “ON”.
(3) Place the active aero switch to AUTO 1.
(4) Using the multi-use tester, increase the vehicle speed
to approx. 80 km/h (50 mph) or more to make sure that
the active aero system is placed to the operative
condition. Then decrease the vehicle speed to approx.
50 km/h (30 mph) or less to confirm that the system
returns to the standard condition.
1 TSB Revision

INTERIOR - Troubleshooting52A-7OPERATION
Key-reminder warning
L0 Battery voltage is always supplied, through
fusible link No. 6 to the key-reminder switch.
l When the driver’s seat is opened while the
ignition key is still in the key cylinder, the door
switch is switched ON, electricity flows to
fusible link No. 6, the key-reminder switch, the
buzzer, the door switch, and ground, and the
buzzer sounds.
Seat belt warning
lBattery voltage is applied, through fuse No. 11
to the ETACS unit when the ignition key is at the
“ON” position.
l Electricity flows to fusible link No. 6, the seat
belt warning light, the ETACS unit, and ground,
and the seat belt warning light flashes for
approx. 6 seconds.
lIf the driver does not buckle the seat belt, the
seat belt switch is switched ON, electricity
flows to fusible link No. 6, the key-reminder
switch, the buzzer, the seat belt switch, the
ETACS unit, and ground, and the buzzer sounds
for approx. 6 seconds.
lWhen the driver buckles the seat belt, the seat
belt switch is switched OFF and the buzzer
stops.
COMPONENT LOCATION
Name1 Symbol (
ETACS unitIA t19FO134TROUBLESHOOTING HINTS
Key-reminder warning
The key-reminder warning doesn’t sound.
(I) The seat belt warning function is OK.
l Check the door switch.
(2) The seat belt warning also doesn’t function.
l Check the buzzer.
Seat belt warning
1. The seat belt warning doesn’t function.
(I) The seat belt warning light flashes.
l Check the seat belt switch.
(2) The seat belt warning light also does not
function (and the key-reminder warning also
does not function).
l Check the key-reminder switch.
2. The buzzer doesn’t stop even though the driv-
er’s seat belt has been buckled.
l Check the seat belt switch.
3. The seat belt warning light doesn’t flashes (but
the buzzer sounds).
l Check the light bulb.
NOTEFor the inspection of the ETACS unit, refer to
P.52A-25.16FO35
1 TSB Revision

52A-26
INTERIOR - Seat Belt
Problem
The warning light flashes, but
the warning buzzer does not
sound.Probable cause
Damaged or discon-netted
wiring of the
seat belt warning
buzzer activationcircuit
Check method
Check by following in-dividual part and the
circuit check No. 2
procedures (P.52A-28).
Remedy
Repair the wiring
harness,
The warning buzzer sounds, but
the warning light does not flash.
The warning light stays on.
The warning light keeps blinking
Malfunction of theReplace the warning
warning buzzerbuzzer.
Malfunction of theReplace the key re-key reminder switch orminder switch or the
the seat belt switchseat belt switch.
Damaged or discon-Check by following in-Repair the wiringnetted wiring of thedividual part and theharness.seat belt warning lightcircuit check No. 2activation circuitprocedures (P.52A-28).
Bulb worn outReplace bulb.
Short-circuit of theCheck by following in-Repair the wiringseat belt warningdividual part and cir-harness.
light and buzzer
cuit check No. 2 pro-activation circuit
cedures (P.52A-28).
Malfunction of theReplace the electron-electronic control unitic control unit.
Malfunction of the-Replace the electron-electronic control unitic control unit.
‘dTSB Revision

52A-28INTERIOR - Seat Belt2. SEAT BELT WARNING LIGHT AND BUZZER ACTIVATION CIRCUIT
Fusible link @
Junctron block(Multr-purpose fuse)
ETACS unit (ECU)Description of operation
Place the ignition switch in the ON position, and the transistor will be turned on, blinking the warning light and
sounding the buzzer four times. However, the warning buzzer will not sound unless the key-reminder switch
and seat belt switch are in the ON position.
Electronic control unit terminal voltage (Disconnect the connector of the electronic control unit andcheck the wiring harness side.)
IIIIIECU terminal No. Signal
ConditionTerminal
voltageI\!
Warning light signalAt all timesSystem
6*1voltage
Warning buzzer signal
Key-reminder switch or seat belt switch “OFF”ov8*2
Key-reminder switch and seat belt switch “ON”System
voltage
NOTE“1. Vehicles without theft-alarm system
“2: Vehicles with theft-alarm systemChecking the individual part
Key-reminder switch: Refer to GROUP 54
- Ignition Switch.dSeat belt switch: Refer to
P.5?A-30.
1 TSB Revision

52B-2SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - General informationGENERAL INFORMATION
INTRODUCTIONThe Supplemental Restraint System (SRS) is de-
signed to supplement the driver’s seat belt to help
reduce the risk or severity of injury to the driver by
activating and deploying a driver’s-side air bag in
certain frontal collisions.
The SRS consists of: left front and right front impact
sensors located, one each, on the right and left front
upper frame lowers; an air bag module located in
the center of the steering wheel, which contains the
folded air bag and an inflator unit; the SRS diagnosis
unit located under the rear console assembly, which
monitors the system, and which contains a safing
impact sensor; an SRS warning light located on the
instrument panel, which indicates the operational
status of the SRS; a clock spring interconnection
located within the steering column; system wiring
and wiring connectors; and a knee bolster located
SRS warning light
M52BAAFunder the steering column.
The SRS is designed so that the air bag will deploy
when the safing sensor, plus either or both of the
left front and right front impact sensors simul-
taneously activate while the ignition switches
“ON”.
That is designed to occur in frontal or near-frontal
impacts of moderate to severe force.
Only authorized service personnel should do work
on or around the SRS components. Those service
personnel should read this manual carefully before
starting any such work. Extreme care must be used
whenservicing the SRS, to avoid injury to the
service personnel (by inadvertent deployment of the
air bag) or the driver (by rendering the SRS inopera-
tive).
SELF-DIAGNOSIS/SRS WARNING LIGHT FUNCTION
The diagnosis unit monitors the SRS system and stores data
concerning any detected faults in the system. When the
ignition key is in “ON” or “START” position, the SRS warning
light should illuminate for about 7 seconds and then turn off.
That indicates that the SRS system is in operational order. If the
SRS warning light does any of the following, immediate
inspection by an authorized dealer is needed.
(1) The SRS warning light does not illuminate as described
above.
(2) The SRS warning light stays on for more than 7 seconds.
(3) The SRS warning light illuminates while driving.
If a vehicle’s SRS warning light is in any of these three
conditions when brought in for inspection, the SRS system
must be inspected, diagnosed and serviced
In accordance wrth
this manual.
TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - General lnform=*ion52B-5
r1.c
L
E.
,
iiCAUTION: SRS diagnosis unit
This unit cannot be repaired.
If defective, remove and replace entire unit per
service manual instructions.
Do not disassemble or tamper.
See service manual for handling and storage
instructions.Driver’s air bag information
This vehicle
ha% an air bag which will supple-
ment the driver’s seatbelt in certain frontal
collisions. The air bag is not a substitute for the
driver’s seatbelt in any type of collision. The
driver, and all other occupants, should wear
seatbelts at all times.
WARNING!
If the “SRS” warning light does not come.on
for about 7 seconds when ignition key is turned
to “ON” or engine is started, or if it stays on
while driving, drive the vehicle to your nearest
authorized dealer right away. Also do so if
vehicle’s front end is damaged or if air bag has
deployed.
The air bag system must be inspected by an
authorized dealer ten years after vehicle manu-
facture date shown on certification label lo-
cated on left front door-latch post or door
frame.Read “SRS” section of your owner’s manual
before driving, for important information, about
Dperation, service and disposal of the air bag
svstem.
Do no drop: keep dry.
Failure to follow instructions could render air
bag inoperative and result in driver injury.
F. CAUTION: SRS
Before replacing steering wheel, read service
manual, center front wheels
ahd align SRS
clock spring neutral marks.
Failure to do so may render SRS system
inoperative, risking serious driver injury.
I.
J.WARNING: SRS
This air bag module cannot be repaired. Do not
disassemble or tamper.
Do not perform diagnosis. Do not touch with
electrical test equipment or probes. Refer to
service manual for further instructions, and for
special handling, storage and disposal proce-
dures.
Tampering or mishandling can result in injury.
Danger! Poison. Keep out of the reach of
children.
Contains sodium acid and potassium nitrate
contents are poisonous and extremely flamm-
able. Contact with acid, water, or heavy metals
may produce harmful and irritating gases or
explosive compounds. Do not dismantle, in-
cinerate or bring into contact with electricity or
store at temperatures exceeding
(93.3”C)
200°F.Fast aid: If contents are swallowed induce
vomiting. For eye contact flush eye with water
for 15 minutes. If gases from acid or water
contact are inhaled, seek fresh air. In every
case, get prompt medical attention.
For additional information, see material safety
data sheet (MSDS) for this product.
CAUTION: SRS clock spring
This is not a repairable part. Do not disassem-
ble or tamper.
If defective, remove and replace entire unit per
service manual instructions.
Before replacement, read service manual, cen-
ter front wheels and align neutral marks.
Failure to
foHow instructions may render SRS
system inoperative, risking serious driver in-
jury.CAUTION: SRS
Before removal of steering gearbox, read ser-
vice manual, center front wheels and remove
ignition key.
Failure to do so may damage SRS clock spring
and render SRS system inoperative, risking
serious driver injury.
TSB Revision