belt MITSUBISHI 380 2005 Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2005, Model line: 380, Model: MITSUBISHI 380 2005Pages: 1500, PDF Size: 47.87 MB
Page 500 of 1500
TRIMS
INTERIOR52A-11
TRIMS
REMOVAL AND INSTALLATIONM1521001100455
1. FRONT SCUFF PLATE
2. COWL SIDE TRIM
REAR SEAT CUSHION (REFER
TO P.52A-55.)
3. REAR SCUFF PLATE
FRONT SEAT BELT LOWER
ANCHOR BOLT
4. FRONT SEAT BELT SASH GUIDE
COVER
5. FRONT SEAT BELT SHOLDER
ANCHOR BOLT
6. CENTER PILLAR COVER
7. CENTER PILLAR TRIM LOWER
8. FRONT DOOR OPENING TRIM
<>9. FRONT PILLAR TRIM
10. REAR DOOR OPENING TRIM
11. CENTER PILLAR TRIM UPPER
REAR SEATBACK ASSEMBLY
(REFER TO P.52A-55.)
12. REAR PILLAR TRIM
13. CHILD RESTRAINT LID
14. REAR SHELF SPEAKER
GARNISH
15. CHILD RESTRAINT LID
16. SEAT BELT GARNISH
17. REAR SHELF TRIM
18. CHILD RESTRAINT FITTING
19. TRUNK ROOM FLOOR BOARD
20. REAR END TRIM
21. TRUNK TRIM SIDE RH
22. TRUNK TRIM, FRONT
23. TRUNK TRIM SIDE LH
24. PARCEL NET ANCHOR
25. JACK ACCESS PANEL
Page 503 of 1500
DOOR TRIM
INTERIOR52A-14
DOOR TRIM
REMOVAL AND INSTALLATIONM1521006400332
Required Special Tool:
MB990784: Ornament Remover
REMOVAL STEPS
<>1. INSIDE HANDLE COVER
<>2. POWER WINDOW SWITCH
PANEL ASSEMBLY
3. ASSIST GRIP CAP
4. BELT LINE INNER
WEATHERSTRIP
5. FRONT DOOR TRIM ASSEMBLY
7. ARMREST BRACKETINSTALLATION STEPS
7. ARMREST BRACKET
6. BELT LINE INNER
WEATHERSTRIP AND FRONT
DOOR TRIM ASSEMBLY
3. ASSIST GRIP CAP
2. POWER WINDOW SWITCH
PANEL ASSEMBLY
1. INSIDE HANDLE COVER
Page 504 of 1500
DOOR TRIM
INTERIOR52A-15
Required Special Tool:
MB990784: Ornament Remover
REMOVAL STEPS
<>1. INSIDE HANDLE COVER
<>2. POWER WINDOW SWITCH
PANEL ASSEMBLY
3. BELT LINE INNER
WEATHERSTRIP
4. REAR DOOR TRIM ASSEMBLY5. ARMREST BRACKET
6. REAR DOOR PANEL BRACKETREMOVAL STEPS (Continued)
Page 510 of 1500
FRONT SEAT ASSEMBLY
INTERIOR52A-21
FRONT SEAT ASSEMBLY
REMOVAL AND INSTALLATIONM1522001300560
Before removing the front seat assembly, refer to GROUP 52B, Service Precautions
P.52B-16 and Air Bag Module and Clock Spring P.52B-237.
2. HEADREST
FRONT SEAT ASSEMBLY
REMOVAL STEPS
3. SEAT BELT SWITCH
CONNECTOR
4. POWER SEAT CONNECTOR RH
6. POWER SEAT CONNECTOR
CONNECTOR
8. FRONT SEAT REAR ANCHOR
COVER
>>A<<10. FRONT SEAT ASSEMBLYFRONT SEAT ASSEMBLY
REMOVAL STEPS (Continued)
Page 511 of 1500
FRONT SEAT ASSEMBLY
INTERIOR52A-22
INSTALLATION SERVICE POINT
.
>>A<< FRONT SEAT ASSEMBLY INSTALLATION
Install the front passenger's seat assembly before install-
ing the outer seat belt.
1. Temporarily tighten the nuts in mounting locations shown in
the illustration with no weight on the front seat cushion and
check the operation of the seat slide.
2. Temporarily tighten the bolts in mounting locations shown in
the illustration with no weight on the front seat cushion.
3. Tighten the nuts and bolts in all mounting locations to the
specified torque.
Page 525 of 1500
Page 530 of 1500
Page 536 of 1500
REAR SEAT CUSHION TRIM COVER
INTERIOR52A-47
REAR SEAT CUSHION TRIM FITMENT
.
1. Locate the new trim onto the pad by aligning the Velcro strip
with the grooves. Use an intersection in order toalign both
directions. Whenever possible work from the centre of the
trim toward the outside.
2. Pull the cover around the sides of the pad.
3. Pull trim through the seat belt slots as shown and attach to
wires
Page 547 of 1500
FRONT SEAT BELT
INTERIOR52A-58
FRONT SEAT BELT
REMOVAL AND INSTALLATIONM1523001300370
SRS: Before removing and installing the seat belts with pre-tensioner, refer to GROUP 52B, Seat
Belt with Pre-tensioner P.52B-250.
NOTE:
*If so equipped
Pre-removal and Post-installation Operation
Turn the ignition key to the LOCK (OFF) position.
Disconnect the negative battery terminal.Post-installation Operation
Adjustment Procedures of Special Function (refer to GROUP
52B, On-Vehicle Service P.52B-250.)
1. EXTENDER SEAT BELT
ASSEMBLY*
OUTER SEAT BELT REMOVAL
STEPS
2. SASH GUIDE COVER
CENTER PILLAR TRIM LOWER
(REFER TO P.52A-11.)
3. OUTER SEAT BELT (REFER TO
GROUP 52B, SEAT BELTS WITH
PRE-TENSIONER P.52B-250.)4. CENTER PILLAR TRIM UPPER
(REFER TO P.52A-11.)
5. ADJUSTABLE SEAT BELT ANCOR
INNER SEAT BELT
6. SEAT BELT SWITCH
CONNECTOR
SHIELD COVER (REFER TO
P.52A-33.)
7. INNER SEAT BELTOUTER SEAT BELT REMOVAL
STEPS (Continued)
Page 548 of 1500
REAR SEAT BELT
INTERIOR52A-59
INSPECTIONM1523004400116.
SEAT BELT SWITCH CONTINUITY CHECK
REAR SEAT BELT
REMOVAL AND INSTALLATIONM1523001600371
ITEM TESTER
CONNECTIONSPECIFIED
CONDITION
Fastened seat belt 1
2 Open circuit
Unfastened seat belt 1
2 Less than 2 ohms
REMOVAL STEPS
REAR SEAT CUSHION
ASSEMBLY (REFER TO
P.52A-55.)
1. INNER SEAT BELT
2. CENTER SEAT BELT INNERREAR SHELF TRIM (REFER TO
P.52A-11.)
3. OUTER SEAT BELT
4. CENTER SEAT BELT OUTERREMOVAL STEPS (Continued)