key battery MITSUBISHI ECLIPSE 1991 Service Manual

BRAKES - Anti-lock Braking System Troubleshooting5-13With the ignition key in the “ON”
posi-Nol
tion, do other warning lights illuminate?
II
YesCheck fuse No. 11. If it is
blown, correct the cause of
the blown fuse and then
replace the fuse.
Does voltage between
har-NoThe harness between thenessconnector terminalcombination meter from
No. 14 and ground indicate) fuse No.1 1 is broken.
battery voltage?
II
Yes
Repair harness.Circuit in combination meter
is broken.Repair or replace
com-
* bination meter.
Turn the ignition switch OFF an
(check.
IIs the ABS warning light normal? (Check
for burned bulb.)
No L A&zed%rning light bulb -Are instrument panel wiring harness,
_Noengine compartment wiring harness,~ Connect connectors firmly.
(Check for pins pulled out or
bent, repair as needed.) body wiring harness and ABS wiring
harness connectors connected properly?drive circuits. Check and repair both

5-14BRAKES - Anti-lock Braking System Troubleshooting
aCheck ABS ECU.
Does the voltage between ECU harness
Not Broken wire between ABSRepair harness.connector terminal No.25 and groundwarning light and ECU
indicate battery voltage?
Yes
Replace ABS ECU.Check ABS valve relay.
I

Is valve relay normReplace valve relay.I
YesInstall the valve relay and, with the
(gnition key in the “ON” position>remove the HU connector and check.
IDoes voltage between the HU harnessNow Broken harness wire be-connetor terminal No.8 and ground
indi-tween ABS warning light
cate battery voltage?and HU
Yes
7II1/---I Repair harness.
Is there continuity between HU harnessNo* Broken harness wire be-Repair harness.connector terminal No.9 and ground?tween HU and groundI
YesHU malfunction
Replace HU.

5-16BRAKES - Anti-lock Braking System Troubleshooting
SUB
IGNITION
FUSIBLE
SWITCHLINK
@W.2)
I I18
ABS ECU9
SELF-DIAGNOSISCHECKCONNECTOR
No - Correct cause of blown
fuse and replace fuse.
YesWith the ignition key in the
“ON” position,
does ,thf
E;;;; relay make a click
’ Yes ’Disconnect ECU connector
and check harness
connec-
tor.
YesWith the ignition key in the
“ON” position, does voltage
between ECU connector ter-
minal No. 18 and ground in-
dicate the battery voltage?
---j-z-
III
I -11 Repair harness.I
YesMalfunction of ABS ECU
Replace ABS ECU.

BRAKES - Anti-lock Braking System Troubleshooting5-17
CABS warning light does not illuminate when ignition key is in “START” position.
-.[Explanation]
The ABS ECU uses the
IG2 power source which is
turned off in the “START” position. The ABS
warning light uses the
IGI power source which is
not turned off even in the “START” position.
Consequently, in the “START” position, power is offand the ECU turns the valve relay OFF. If the
warning light does not illuminate at this time, there
is trouble in the warning light circuit on the valve
relay side.
MAINIGNITIONFUSIBLESWITCHLINK @(iG1)I
J/B58
15
ABS ECUWith the ignition key in the
“ON” position, does voltagebetween body connector
terminal
No.8 and groundindicate the battery voltage?
Yes

5-18BRAKES - Anti-lock Braking System Troubleshooting
DABS warning light blinks once after the ignition key is turned to the “ON” position. It
illuminates in the “START” position and blinks once again when turned to the “ON” position.
[Explanation]
When power flows, the ABS ECU turns on the
harness between the ECU and the warning light, thewarning light for approximately 1 sec. while itlight illuminates only when the valve relay is off in
performs a valve relay test. If there is a break in thethe valve relay test, etc.
125
El
ABS ECU
14A0597connector and check with
I
In the ignition key “ON”
_ No ~ Harness wire between
position, does voltage
be-ABS warning light and
tween terminal No.25 andECU is broken.
ground indicate battery vol-
tage?
YesRepair harness.
tMalfunction of ABS ECU
Replace ABS ECU.

5-28BRAKES -Anti-lock Braking System Troubleshooting
With the ignition key in the “ON”
posi-NoCheck fuse No.ll. If it is
tion, do other warning lights illuminate?blown, correct the cause of
the blown fuse and then
replace the fuse.
YesTurn the ignition switch OFF and
Does voltage between
har-NOThe harness between the
nessNo. 14 and ground indicate
battery voltage?) fuse No.1 1 is broken.
YesCircuit in combination meter
is broken.
tRepair or replace com-
bination meter.II
IIIs the ABS warning light normal? (CheckNO) ABS warning light bulbReplace ABS warning
for burned bulb.)
burned.* light bulb.
I
Yes
- No
Are instrument panel wiring harness,
engine compartment wiring harness,
body wiring harness and ABS wiring
harness connectors connected properly?
c Connect connectors firmly.
(Check for pins pulled out or
bent, repair as needed.)
YesBroken wire in ECU, valve relay or both
drive circuits. Check and repair both
circuits.

BRAKES - Anti-lock Braking System Troubleshooting5-31
SUBIGNITION
%TB(kEzYCH
IODE
;LLF-FIAGNOSIS
CONNECTOR
I Yes1,
With the ignition key in the
No _ Is power relay normal?
“ON” position, does the
(Refer to P.5-52.)power relay make a “click”:
noise?LDisconnect ECU connector
and check harness connec-Replace power relay.
tor.
YesWith the ignition key in the
“ON” position, does voltage
between ECU connector ter-
minal No. 18 and ground in-
dicate the battery voltage?
Yes
Yes
Replace ABS ECU.

5-32BRAKES -Anti-lock Braking System Troubleshooting
CABS warning light does not illuminate when ignition key is in “START” position.
[Explanation]The ABS ECU uses the
IG2 power source which isand the ECU turns the valve relay OFF. If the
turned off in the “START” position. The ABSwarning light does not illuminate at this time, there
warning light uses the
IGI power source which isis trouble in the warning light circuit on the valve
not turned off even in the “START” position.relay side.
Consequently, in the “START” position, power is off
MAINIGNITIONFUSIBLESWITCHLINK @I(IGl)J/B
“62
I .1411213141516l7l61911112113114115U6i,79
@COMBINATIONAL METER
“58ABS ECU
1410000
hydraulicunit (HU) connector and
>\/I
1With the ignition key in the
“ON” position, does voltage
between body connector
terminal No.8 and ground
indicate the battery voltage?
Is there continuity between
No~Broken line between HU
body connector terminaland body groundNo.9 and ground?
I
YesIs there continuity between
HU connector terminal No. 8and terminal
No.9?
YesRemove the valve relay. Is
there continuity between
terminal No. 87a and No. 30?
I
Yes1 Replace valve relay.
HU harness malfunction
I
1 Replace HU.

BRAKES - Anti-lock Braking System Troubleshooting5-33
DABS warning light blinks once after the ignition key is turned to the “ON” position. It
illuminates in the “START” position and blinks once again when turned to the “ON” position.*-_
[Explanation ]When power flows, the ABS ECU turns on the
harness between the ECU and the warning light, thewarning light for approximately 1 sec. while itlight illuminates only when the valve relay is off in
performs a valve relay test. If there is a break in the
the valve relay test, etc.
Y
x %l4
9
4
n. 58
ABS ECU
14A0597
EC
4connector and check with
he harness connector. /\/
IIn the ignition key “ON”
position, does voltage be-
tween terminal
No.25 andground indicate battery vol-
tage?
Replace ABS ECU.I

5-36BRAKES - Anti-lock Braking System Troubleshooting
E-3Abnormality of G sensor circuit
[Explanation]The ABS ECU turns on the warning light in the
following cases.
lOFF trouble turning G sensor OFF (It is judged
that the
G sensor continues to be OFF for more
than approximately 13 seconds except when the
lWhen there is a broken wire or short circuit in
the harness for the
G sensor system.
PlUN; F;SIBLEIGNITIONSWITCH (IG2)J/B
G-SENSOR
E-lABSECU
14AO609
Is G sensor normal? (ReferNoto
P.5-86.)Replace G sensor.
I YesWith the ignition key “ON”
_ No m The harness between the
does the voltage betweenG sensor and the ABS
terminal No.6 and groundECU is broken.
indicate battery voltage?
IG sensor circuit is normal.I