table MITSUBISHI ENDEAVOR 2004 Service Service Manual

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Fig. 101: Data List Reference Table (2 Of 2)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
PCM TERMINAL VOLTAGE REFERENCE CHART FOR AUTO-CRUISE CONTROL SYSTEM
OPERATION 1. Disconnect the PCM connectors, and connect special tool MB991923 in
between.
2. Measure the voltage between each check connector terminals of special tool
MB991923 and
ground terminals 63 or 76.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

Fig. 102: Identifying Special Tool
-Power Plant ECU Check Harness Connector
(Component Side)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 103: Auto Cruise Control System Operation Table (1 Of 2)

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Fig. 104: Auto Cruise Control System Operation Table (2 Of 2)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ON-VEHICLE SERVICE AUTO-CRUISE CONTROL MAIN SWITCH CHECK 1. Turn the i
gnition to the "ON"
position.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

Fig. 111: Identifying Condition Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
TRANSMISSION RANGE SWITCH ("N" POSITIN) Refer to ESSENTIAL SERVICE
.
THROTTLE POSITION SENSOR Refer to THROTTLE ACTUATOR CONTROL MOTOR CHECK
.
AUTO-CRUISE CONTROL SWITCH CHECK 1. Remove the auto-cruise control switch. (Refer to AUTO
-CRUISE
CONTROL
).
2. Measure the resistance between terminal 2 and terminal 3 when each of the
"COAST/SET", "ACC/RES", "CANCEL" and "CRUISE" (MAIN) switches is

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

pressed. If the values measured at the time correspond to those in the table below, the resistance values are correct.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

Fig. 112: Checking Auto Cruise Control Switc
h
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 113: Identifying Switch Position And Specified Condition Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
AUTO-CRUISE CONTROL REMOVAL AND INSTALLATION
WARNING:Before removal of the air bag module, refer to AIR
BAG SAFETY PRECAUTIONS
and DRIVER
-SIDE AIR
BAG MODULE & CLOCKSPRING
.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

2 .
3. Turn the ignition switch to the ON position and select BELT TENSION
MEASUREMENT from the menu screen on Scan Tool (MB991958).
4. Hold Microphone (part of Belt Drive Meter Set) (MB991668) near the center
of the drive belt between the pulleys away from the rear surface of the belt and
perpendicular to the belt (no more then 15 degrees in either direction). See Fi
g.
3 and Fig. 4
.
5. Gently tap the middle of the belt between the pulleys with your finger, and
check that the vibration frequency of the belt is within specification. See Fig. 3
and Fig. 4
. See DRIVE BELT ADJUSTMENT SPECIFICATIONS
table.
CAUTION: Temperature of the surface of the belt should be
as close possible to underhood temperature.
CAUTION: DO NOT let contaminants such as water or oil get
onto the microphone. If strong gusts of wind
blow against the microphone or if there are any
loud sources of noise nearby, the values
measured by the microphone may not
correspond to actual values. DO NOT take
measurement while engine is running.

2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor

Fig. 4: Checking Vibration Frequency (Power Steering Pump Belt)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Using Tension Gauge Use a belt tension gauge to check that the belt tension is within specification. See
Fig. 5
an
d Fig. 6
. See DRIVE BELT ADJUSTMENT SPECIFICATIONS
table.

2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor

Fig. 6: Checking Drive Belt Tension (Power Steering Pump Belt)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Measuring Belt Deflection Apply 22 lbs. (98 N) of force to the middle of the drive belt between the pulleys.
See Fig. 7
and Fig. 8
. Check that amount of deflection is within specifications. See
DRIVE BELT ADJUSTMENT SPECIFICATIONS
table.

2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor

1. Loosen the tensioner pulley fixing bolt. See Fig. 9
.
2. Temporarily tighten the tensioner pulley fixing nut to 7-15 ft. lbs. (10-20 N.m).
Ensure belt frequency, tension, or deflection is to specification. See DRIVE
BELT ADJUSTMENT SPECIFICATIONS
table.
Fig. 9: Adjusting Generator Drive Belt

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Power Steering Pump Belt 1. Loosen the tensioner pulley lock nut. See Fig. 10
.
NOTE: The tension will increase when the turning the adjusting
bolt clockwise, and decrease when turning adjusting
bolt counterclockwise.

2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor