Air con MITSUBISHI LANCER 2005 Owners Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2005, Model line: LANCER, Model: MITSUBISHI LANCER 2005Pages: 788, PDF Size: 45.98 MB
Page 440 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-52
STEP 2. Connector check: Combination meter
connector C-06 and engine coolant temperature
gauge unit connector B-112
Q: Is combination meter connector C-06 and engine
coolant temperature gauge unit connector B-112 in
good condition?
YES :
Go to Step 3.
NO : Repair or replace the damage
component(s).
STEP 3. Check the wiring harness between
combination meter connector C-06 (terminal 50)
and engine coolant temperature gauge unit
connector B-112 (terminal 1).
AC303784
Connector: B-112
<4G1-MPI>
Harness side
B-112 (B)
AF
AC303792
AE
Connector: B-112
<4G6-MPI>
B-112 (B) Harness side
AC303798
Connector: C-06
Harness side
C-06 (L)
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
AV
AC303814AU
Connector: C-06
Harness side
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
C-06 (L)
AC303784
Connector: B-112
<4G1-MPI>
Harness side
B-112 (B)
AF
AC303792
AE
Connector: B-112
<4G6-MPI>
B-112 (B) Harness side
AC303798
Connector: C-06
Harness side
C-06 (L)
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
AV
AC303814AU
Connector: C-06
Harness side
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
C-06 (L)
Page 441 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-53
NOTE:
Prior to the wiring harness inspection, check
intermediate connectors C-13
C-137
connector C-06 (terminal 50) and engine coolant
temperature gauge unit connector B-112 (terminal
1) in good condition?
YES :
Go to Step 4.
NO : Repair or replace the damage
component(s).
STEP 4. Retest the system
Q: Is the engine coolant temperature gauge normal?
YES :
The procedure is complete. If no
malfunctions are found in all steps, an
intermittent malfunction is suspected (Refer
to GROUP 00, How to Use
Troubleshooting/Inspection Service
Points-How to Cope with Intermittent
Malfunction P.00-5).
NO : Replace the combination meter.
AC303800
Connector: C-13
Harness side
AG
AC303818
AM
Connector: C-137
Harness side
Page 443 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-55
DIAGNOSIS PROCEDURE
STEP 1. Voltage measurement at combination
meter connector C-04 in order to check the
battery circuit of power supply system to the
combination meter.
(1) Disconnect the combination meter connector
C-04 and measure the voltage at combination
meter connector C-04 harness side.
(2) Measure the voltage between terminal 7 and
earth.
OK: System voltage
Q: IS the check result normal?
YES :
Go to Step 4.
NO : Go to Step 2.
STEP 2. Connector check: Combination meter
connector C-04.
Q: Is combination meter connector C-04 in good
condition?
YES :
Go to Step 3.
NO : Repair or replace the connector. Check to
see that all meters operate.
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
AC301541
Connector C-04
(Harness side)
EZ
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
Page 444 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-56
STEP 3. Check the wiring harness between
combination meter connector C-04 (terminal 7)
and battery.
NOTE: .Prior to the wiring harness inspection, check
intermediate connectors C-27
C-115
and repair if necessary.
Q: Are the wiring harness between combination meter
connector C-04 (terminal 7) and battery in good
condition?
YES :
There is no action to be taken.
NO : Repair or replace the wiring harness. Check
to see that all meters operate.
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
AC303798AX
Connector: C-27
Harness side
AC303802
Connector: C-103
Harness sideC-103 (GR)
AG
AC303818
AO
Connector: C-103
Harness side
C-103 (GR)
AC303816
Connector: C-115
Harness side
AZ
Page 445 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-57
STEP 4. Voltage measurement at combination
meter connector C-04 to check the battery circuit
of power supply system to the combination
meter.
(1) Measure at combination meter connector C-04
without disconnecting the connector.
(2) Turn the ignition switch to “ON” position.
(3) Measure the voltage between terminal 9 and
earth.
OK: System voltageQ: Is the check result normal?
YES :
Go to Step 7.
NO : Go to Step 5.
STEP 5. Connector check: combination meter
connector C-04
Q: Is combination meter connector C-04 in good
condition?
YES :
Go to Step 6.
NO : Repair or replace the connector. Check to
see that all meters operate.
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
AC301541
Connector: C-04
(Harness side)
FA
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
Page 446 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-58
STEP 6. Check the wiring harness between
combination meter connector C-04 (terminal 9)
and ignition switch (IG1).
NOTE: Prior to the wiring harness inspection, check
Junction block connectors C-210 and C-212, joint
connector C-03
necessary.
Q: Are the wiring harness between combination meter
connector C-04 (terminal 42) and ignition switch
(IG1) in good condition?
YES :
There is no action to be taken.
NO : Repair or replace the wiring harness. Check
to see that all meters operate.
AC303798AU
Connector: C-03, C-04
C-03 (B)
C-04 C-03 Harness side
AC303814
Connector: C-04
Harness side
AT
AC303809
Connector: C-210, C-212
C-212
C-210
C-210 Harness side
C-212
AX
Front view
AC303823
Connector: C-210, C-212
C-210
C-212Front view
Harness side
C-210
C-212
AU
Page 447 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-59
STEP 7. Resistance measurement at combination
meter connector C-04 to check the earth circuit
to the combination meter.
(1) Disconnect the combination meter connector
C-04 and measure the resistance at combination
meter connector C-04.
(2) Measure the resistance between terminal 1 and
earth.
OK: 2 ohms or less
(3) Measure the resistance between terminal 2 and
earth.
OK: 2 ohms or lessQ: Is the check result normal?
YES :
Repair or replace the connector.
NO : Go to Step 8.
STEP 8. Connector check: Combination meter
connector C-04.
Q: Is combination meter connector C-04 in good
condition?
YES :
Go to Step 9.
NO : Repair or replace the wiring harness. Check
to see that all meters operate.
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
AC301541FB
Connector: C-04
(Harness side)
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
Page 448 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-60
STEP 9. Check the wiring harness between
combination meter connector C-04 (terminal 1
and 2) and earth.
Q: Are the wiring harness between combination meter
connector C-04 (terminal 1 and 2) and earth in
good condition?
YES :
This procedure is complete.
NO : Repair or replace the wiring harness. Check
to see that all meters operate.
ON-VEHICLE SERVICE
SPEEDOMETER CHECKM1543000900423
Adjust the pressure of tyres to the specified level.
(Refer to GROUP 31, On-vehicle Service P.31-7.)
CAUTION
Do not operate the clutch suddenly. Do not
increase/decrease speed rapidly while testing.
1. Set the vehicle onto a speedometer tester and
use wheel chocks to hold the rear wheels.2. To prevent the front wheel from moving from side
to side, attach tension bars to the tie-down hook,
and secure both ends to anchor plates.
3. To prevent the vehicle from moving, attach a chain
or wire to the rear retraction hook, and make sure
the end of the chain or wire is secured.
4. Check if the speedometer indicator range is within
the standard values.
Standard value:
5. If not to the standard value, inspect for proper tyre
size. If not correct, replace the tyres with original
size tyres and retest. If correct, replace the
speedometer. If still not to standard value, replace
the vehicle speed sensor.
TACHOMETER CHECKM1543001000434
1. Attach an external high quality tachometer to the
engine speed detection connector on the harness
side (such as with a paper clip).
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
AC305135AB
Wheel stopper
Standard indicator
km/h (mph)Allowance range km/h
(mph)
20 (12) 20 − 24 (12 − 15)
40 (25) 40 − 44 (25 − 28)
80 (50) 80 − 85 (50 − 53)
120 (75) 121 − 127 (75 − 79)
160 (100) 162 − 169 (100 − 105)
200 (125) 203 − 211 (126 − 131)
AC001288
Tension bar
Front
Anchor plate
AB
AC305138AB
Engine speed
indicator
Paper clip
Probe for detection
of engine speed
Page 473 of 788
HAZARD WARNING LAMP SWITCH
CHASSIS ELECTRICAL54A-85
HAZARD WARNING LAMP SWITCH
TROUBLESHOOTING
M1542000701333
FLASHER TIMER FUNCTION
The hazard warning lamps (flasher timer function)
are controlled by the Smart Wiring System (SWS).
For troubleshooting, refer to respective Groups
below.•Not using SWS monitor: GROUP 54B, SWS
Troubleshooting P.54B-38.
•Using SWS monitor: GROUP 54C, SWS
Troubleshooting P.54C-22.
SPECIAL TOOL
M1542000600935
AC304717AB
2
1 3 4
56
Removal steps
1. Licence plate lamp lens
2. Packing
3. Licence plate lamp body4. Socket
5. Licence plate lamp bulb
6. HarnessRemoval steps (Continued)
Tool Number Name Use
MB990784 Ornament remover Removal of centre panel and
centre air outlet panel
MB990784
Page 474 of 788
HAZARD WARNING LAMP SWITCH
CHASSIS ELECTRICAL54A-86
HAZARD WARNING LAMP SWITCH
REMOVAL AND INSTALLATIONM1542006600449
INSPECTIONM1542011200920
HAZARD WARNING LAMP SWITCH
CONTINUITY CHECK
AC304721AB
3
4
2
15
Removal steps
1. Knob
2. Centre panel
3. Meter bezel4. Centre air outlet panel
5. Hazard warning lamp switchRemoval steps (Continued)
AC305304
Switch position Tester
connectionSpecified
condition
Released 1 − 2 Open circuit
Pressed 1 − 2 Less than 2
ohms