window MITSUBISHI LANCER 2005 User Guide

WINDOW GLASS
BODY42-18
5. Install the glass stopper and window dam to the
specified positions so that there are no adrift or
bent surfaces inside the rear window glass.
6. Install the rear window upper moulding.
7. Install the glass in the same manner as the
windshield. (Refer to P.42-12.)>>B<< REAR WINDOW LOWER
MOULDING INSTALLATION
Install the clips to the rear window lower moulding,
and then fix the rear window moulding to the vehicle
body.
Y0630AU
Y0629AU
AC006075
Glass stopper and window dam installation position
Glass stopper
18 mm
Glass end line
Align the glass
stopper end with
the ceramic notch.
Ceramic line
Rear window
glass
A
ASection A - A
19 mmWindow dam Align the window
dam end with
the ceramic notch.
Mark
Seal line
Ceramic
line
Window dam
19 mm
AB

WINDOW GLASS
BODY42-19
QUARTER WINDOW GLASS
REMOVAL AND INSTALLATIONM1422002500247
Pre-removal and Post-installation Operation
•Quarter Trim Upper Removal and Installation (Refer to
GROUP 52A, Trims P.52A-11).
AC304783
N
N
N
12
3
N3 4
AB
Y1509AU
Y1508AU
Y1507AU
Y1485AU
Y1535AU
AC304784
AAB B
DD
C
C
Mark
Apply the primer and adhesive
along the fictitious lines (seal line)
between each of the marks.
Adhesive: 3M ATD Part No. 8609 Super Fast Urethane Auto Glass Sealant or equivalent and
3M ATD Part No. 8608 Super Fast Urethane Primer or equivalent
1 11
Seal line centrePrimer Section A – A Section B – BSeal line
centre
Primer
Section C – C Section D – D
Seal line
centrePrimer
1Seal line
centre
Units: mm
Primer
16
161616
Ceramic line
AB
Removal steps
<> >>B<<1. Quarter window glass assembly
>>A<<2. Dual lock fastener
>>A<<3. Clip
>>A<<4. GasketRemoval steps (Continued)

WINDOW GLASS
BODY42-20
REMOVAL SERVICE POINT
<> QUARTER WINDOW GLASS
REMOVAL
1. Apply cloth tape to protect the quarter window
glass.
2. Use glass adhesive knife to cut away adhesive.
CAUTION
Inserting the adhesive knife too deeply into
windshield adhesive may damage quarter
window glass.
3. Keep the glass adhesive knife at right angles with
body flange (from inside the vehicle), and put the
blade at body flange. Then cut away adhesive
along the body flange.4. Make mating marks on the quarter window glass
and body.
5. Use special tool glass holder (MB990480) to
remove the quarter window glass.
CAUTION
•Be careful not to remove more adhesive than
is necessary.
•Be careful also not to damage the paintwork
on the body surface with the knife. If the
paintwork is damaged, repair the damaged
area with repair paint or anti-rust agent.
6. Use a knife to cut away the remaining adhesive so
that the thickness is within 2 mm around the entire
circumference of the body flange.
7. Finish the flange surfaces so that they are
smooth.
CAUTION
Allow the cleaned area to dry for at least three
minutes. Do not touch any surface that has been
cleaned.
8. When reusing the quarter window glass, remove
the adhesive still adhering to the quarter window
glass, and clean with isopropyl alcohol.
9. Clean the body side in the same way.
AC103600
ADCloth tape
AC002060
AC301614AB
Glass adhesive knife
AC103605AD
MB990480
ACX00476
AB

WINDOW GLASS
BODY42-21
INSTALLATION SERVICE POINTS
>>A<< GASKET/CLIP/DUAL LOCK
FASTENER INSTALLATION
1. Carry out the following procedure to re-install
quarter window glass.
CAUTION
Do not forget gasket.
(1) Fit clips into body.
(2) Cut away clip fitting convex on quarter window
glass.
NOTE: Convex gets broken when quarter
window glass is removed.
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
2. Use isopropyl alcohol to degrease the inside and
outside of the quarter window glass and the body
flanges.
3. Assemble the dual lock fastener according to the
standard location of the body flange.
4. Assemble the dual lock fastener to the quarter
window glass relative to the body flange dual lock
fastener.
>>B<< QUARTER WINDOW GLASS
INSTALLATION
Remove the quarter window glass using the same
procedure as for the windshield removal (Refer to
P.42-12).
AC103606
AC
Cut off these convex parts
AC304793AB
Dual lock fastener
Install the dual lock fastener
with aligning it onto the bumps
of the body flange.

WINDOW GLASS
BODY42-22
TAILGATE WINDOW GLASS
REMOVAL AND INSTALLATIONM1422003700170
Pre-removal and Post-installation Operation
•Tailgate Trim Removal and Installation (Refer to GROUP
52A, Tailgate Trim P.52A-19).
•Tailgate Spoiler Assembly Removal and Installation
(Refer to GROUP 51, Tailgate Spoiler P.51-19).
•Rear Wiper Arm Assembly Removal and Installation
(Refer to GROUP 51, Rear Wiper and Washer P.51-29).
AC304811
1
2
6 55
4 33 7
AB
N
NN
N
N
N
N
Y1522AU
Y1538AU
AC304812
Y1537AUY1537AU
AB
Units: mm
Adhesive: 3M ATD Part No. 8609 Super Fast Urethane Auto Glass Sealant or equivalent and
3M ATD Part No. 8608 Super Fast Urethane Primer or equivalentSection A – A
13
14
14 Section B – B
Section C – C A
A
CC
B
B Ceramic line
Mark Apply the primer and adhesive
along the fictitious lines (seal line)
between each of the marks.
Seal line
centrePrimer
Seal line
centrePrimer
Seal line
centre
Primer
22
2

WINDOW GLASS
BODY42-23
REMOVAL SERVICE POINT
<> TAILGATE WINDOW GLASS
REMOVAL
Remove the tailgate window glass using the same
procedure as for the windshield (Refer to P.42-12).
INSTALLATION SERVICE POINTS
>>A<< WINDOW SPACER/GLASS
STOPPER/DUAL LOCK
FASTENER/WINDOW DAM
INSTALLATION
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
1. Use isopropyl alcohol to degrease the inside and
outside edges of the tailgate window glass and
the surface of the tailgate flange.
Removal steps
1. Connecting the harness connector
<> >>B<<2. Tailgate window glass
>>A<<3. Window lower dam
>>A<<4. Window side dam
>>A<<5. Dual lock fastener
>>A<<6. Glass stopper
>>A<<7. Window spacerRemoval steps (Continued)

WINDOW GLASS
BODY42-24
2. Assemble the window spacer, glass stopper and
window dam to the tailgate window glass location
shown.3. Assemble the dual lock fastener according to the
standard location of the tailgate flange.
4. Assemble the dual lock fastener to the quarter
window glass relative to the tailgate flange dual
lock fastener.
>>B<< TAILGATE WINDOW GLASS
INSTALLATION
Install the tailgate window glass in the same way as
for the windshield installation (Refer to P.42-12).
AC107207
AC107207
Y1484AUY1484AU
AC304816
AB
Glass stopper Glass spacer
Seal lineCeramic lineCeramic lineGlass end line
Glass end line Window spacer, glass stopper and window dam installation position
Align the glass spacer and with
the tailgate window glass mark.
Position the window side dam
2 mm inside from the tailgate
window glass end.
Butt the ends of
the window lower
and side dams.
Align the glass stopper and with
the tailgate window glass mark.
Seal line
Seal line 22 mm 14.5 mm
2 mm
Tailgate window glass
Window lower dam Window side dam
AC304849AB
Dual lock fastener Flange convex at the tailgate flange

DOOR
BODY42-25
DOOR
SERVICE SPECIFICATIONSM1423000300091
SEALANTM1423000500095
SPECIAL TOOLSM1423000600337
ItemStandard value
Power window operation current (Power supply voltage 14.5 ± 0.5 V, at 25 °C) A 5 ± 1
Door outside handle play mm Front door 2.6 ± 2.5
Rear door 1.3 ± 1.3
Door inside handle play mm Front door 10.4 ± 9.6
Rear door 10 ± 9.6
Item Specified sealant
Door waterproof film 3M ATD Part No.8633 or equivalent
Tool Number Name Use
MB990480 Window glass holder Removal of power window regulator
assembly
MB990900 or
MB991164Door hinge adjusting
wrenchDoor alignment
MB990925
A: MB990939Bearing and oil seal
installer set
A: Brass barDoor striker adjustment
MB990211 Sliding hammer
MB990241
A: MB990243Axle shaft puller
A: Body puller
MB990480
MB990900
MB990925AF
A
MB990211
MB990241
A
AE

DOOR
BODY42-28
DOOR WINDOW GLASS ADJUSTMENTM1423001000327
Check that the door glass moves while contacting
the door glass channel when it is raised and lowered
fully. If not, adjust the door window according to the
following procedures.
1. Remove the door trim assembly (Refer to GROUP
52A, Door trim P.52A-15).
2. Remove the waterproof film (Refer to P.42-39).
3. Loosen the door glass mounting screw via the
adjusting hole with the door window glass fully
closed, then lower the window glass a little.
4. Fully close the door window glass again and
tighten the door glass mounting screw firmly via
the adjusting hole.
GLASS SLIDING MECHANISM CHECK
AND ADJUSTMENT
M1429000900091
If the window glass automatically starts moving
downwards at the wrong time while it is being raised,
carry out the following adjustment or replacement
procedures.
1. Remove the door trim assembly (Refer to GROUP
52A, Door trim P.52A-15).
2. Remove the waterproof film (Refer to P.42-39).
3. Remove the window regulator assembly from the
door window glass, and then raise and lower the
door window glass by hand to check the operation
force.
NOTE: Insert a cushion or similar object to
prevent damage to the glass if it should happen to
fall down.4. If the door window glass does not move up and
down smoothly, check or repair the following
points.
•Check the installation condition of the
runchannel.
•Repair any twisting in the door sash.
•Check the installation condition of the lower sash
or the centre sash.
NOTE: The lower sash cannot normally be
adjusted, but it may be possible to adjust the sash
span slightly within the range allowed by
manufacturing tolerances by pushing the lower
sash outwards while re-installing it.
5. If repair or adjustment is not possible, replace the
door assembly.
POWER WINDOW OPERATING CURRENT
CHECK
M1429001100184
1. Remove the power window fuse and connect an
ammeter as shown in the illustration.
2. When the power window switch is pressed to the
“UP” position, a large amount of current flows at
the time the window starts to close and when it is
fully closed, so measure the operation current in
the interval between these two points.
Standard value (A): 5 ± 1A (Power supply
voltage 14.5 ± 0.5V, 25°C)
Y0238AUY0239AUAC006112
AB

Adjusting
holeAdjusting
hole
AC003777
RunchannelDoor
sash
Lower
sash
AB
AC006115AB