lock MITSUBISHI LANCER EVOLUTION 2007 Service Owner's Guide

INDEX - In order of parts nameC-12
Wiring diagram
page Circuit diagram page Connector
No. Parts name
CColumn switchC-203B-104,107,112,116,125,128,137,141,
187,191B-22,28
Combination meterC-01B-84,87,95,103,106,118,122,126,129,
135,139,148,149,152,153,156,157,
198,206,214,222,230,240,248,250,
256, 258B-18,24
Combination meterC-02B-110,115,118,122,126,129,135,139,
148,149,152,153,156,157,198,206,
248, 250,256,258B-18,24
Condenser fan motorA-45B-177,183B-7,9
Condenser fan motorA-46B-177,183B-7,9
Condenser fan relay (HI)A-07XB-73,177,183B-6,8
Condenser fan relay (LO)A-06XB-73,177,183B-6,8
Control wiring harness and battery
wiring harness combinationB-14B-79,84,91,99,157B-10,14
Control wiring harness and floor wiring
harness (LH) combination
C-46B-224,244B-25
Crank angle sensorB-121B-88,96B-13,16
DDefogger (-)F-06B-185B-38,39
Defogger (+)F-19B-185B-38,39
Defogger relayC-214B-54,55,78,185B-23,29
Detonation sensorB-122B-89,97B-13,17
Diagnosis connectorC-22B-92,100,105,108,113,117,119,123,
125,128,137,141,150,154,158,164,
170,172,188,189,204,205,219,227,
237,247,248,250,252,254B-18,24
Diagnosis connectorC-23B-92,100B-18,24
Direction valve (LH) F-25B-235,245B-38,39
Direction valve (RH) F-26B-235,245B-38,39
Door lock actuator (Front:LH)E-08B-170,173B-34,36
Door lock actuator (Front:RH)E-18B-171,172B-35,37
Door lock actuator (Rear:LH)E-12B-171,173B-34,36
Door lock actuator (Rear:RH)E-23B-171,173B-35,37
Door lock key cylinder switch (LH)E-17B-172B-37
Door lock key cylinder switch (RH)E-16B-170B-35
Door switch (Front:LH)D-13B-105,112,120,121,158B-30,32
Door switch (Front:RH)D-01B-108,116,120,121,164B-30,32

GENERAL -How to Use Troubleshooting/Inspection Service Points00-7
4. INSPECTION CHART FOR DIAGNOSIS CODES
5. INSPECTION PROCEDURE FOR DIAGNOSIS CODES
Indicates the inspection procedures corresponding to each diagnosis code. (Refer to P.00-10 for how
to use the inspection procedures.)
6. INSPECTION CHART FOR TROUBLE SYMPTOMS
If there are trouble symptoms even though the results of inspection using the MUT-IIshow that all
diagnosis codes are normal, inspection procedures for each trouble symptom will be found by means
of this chart.
7. INSPECTION PROCEDURE FOR TROUBLE SYMPTOM
Indicates the inspection procedures corresponding to each trouble symptoms classified in the Inspection
Chart for Trouble Symptoms. (Refer to P.00-10 for how to use the inspection procedures.)
8. SERVICE DATA REFERENCE TABLE
Inspection items and normal judgement values have been provided in this chart as reference information.
9. CHECK AT ECU TERMINALS
Terminal numbers for the ECU connectors, inspection items and standard values have been provided
in this chart as reference information.
10. INSPECTION PROCEDURES USING AN OSCILLOSCOPE
When there are inspection procedures using an oscilloscope, these are listed here.
DIAGNOSIS FUNCTION
METHOD OF READING DIAGNOSIS CODES
WHEN USING THE MUT-II
Connect the MUT-IIto the diagnosis connector and take a
reading of the diagnosis codes.
Caution
Turn the ignition switch to “LOCK”(OFF) position before
connecting or disconnecting the MUT-II.
MUT-˜

GENERAL -How to Use Troubleshooting/Inspection Service Points00-8
WHEN USING THE WARNING LAMP
1. Use the special tool to earth No.1 terminal (diagnosis
control terminal) of the diagnosis connector.
2. Turn the ignition switch to “ON” position.
3. Read out a diagnosis code by observing how the warning
lamp flashes.
Applicable systems
System nameWarning lamp name
ACD, AYCACD mode indicator lamp
ABSABS warning lamp
Indication of diagnosis code by warning lamp
When the diagnosis code No.24 is outputWhen no diagnosis code is output*
On
Off
1.5 secs.0.5 sec.
0.5 sec.
Pause
time 3
secs.Tens
signalPlace
division
2 secs.Units
signal
On
Off
0.25 sec.
METHOD OF ERASING DIAGNOSIS CODES
WHEN USING THE MUT-II
Connect the MUT-IIto the diagnosis connector and erase the diagnosis code.
Caution
Turn the ignition switch to “LOCK”(OFF) position before connecting or disconnecting the MUT-II.
WHEN NOT USING THE MUT-II
1. Turn the ignition switch to “LOCK”(OFF) position.
2. After disconnecting the battery cable from the battery ( - ) terminal for 10 seconds or more, reconnect
the cable.
3. After the engine has warmed up, run it at idle for about 15 minutes.
MB991529

GENERAL -How to Use Troubleshooting/Inspection Service Points00-9
INPUT SIGNAL CHECK
WHEN USING THE MUT-II
1. Connect the MUT-IIto the diagnosis connector and erase
the diagnosis code.
Caution
Turn the ignition switch to “LOCK”(OFF) position
before connecting or disconnecting the MUT-II.
2. If the MUT-IIbuzzer sounds once when each switch is
operated (ON/OFF), the input signal for that switch circuit
system is normal.
WHEN USING A VOLTMETER
1. Use the special tool to connect the ETACS terminal
(terminal 9) and the earth terminals (terminals 4 and 5)
of the diagnosis connector to the voltage meter.
2. If the needle of the voltage meter flickers once when
each switch is operated (ON/OFF), the input signal for
that switch circuit system is normal.MUT-˜
MB991529

GENERAL -Vehicle IdentificationGENERAL -Vehicle Identification00-16
CHASSIS NUMBER
The chassis number is stamped on the toeboard inside the
engine compartment.
1
234
5
67
8911
10
No.ItemsContents
1Fixed figureJAsia
2Distribution channelMJapan channel
3DestinationYFor Europe and General Export
4Body styleS4-door sedan
5Transmission typeN5-speed manual transmission
6Development orderCTMITSUBISHI LANCER EVOLUTION-VII
7Engine94G63: 1,997 mL petrol engine
8SortAPassenger car
9Model year22002
10PlantUMIZUSHIMA-1
11Serial number--
ENGINE MODEL NUMBER
1. The engine model number is stamped on the cylinder
block as shown below.
Engine modelEngine displacement mL
4G631,997
2. The engine serial number is stamped near the engine
model number.
Engine serial numberAA0201 to YY9999

GENERAL -Precautions Before Service00-18
PRECAUTIONS BEFORE SERVICE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
1. Items to follow when servicing SRS
(1) Be sure to read GROUP 52B - Supplemental Restraint System (SRS).
For safe operations, please follow the directions and heed all warnings.
(2) Wait at least 60 seconds after disconnecting the battery cable before doing any further work.
The SRS system is designed to retain enough voltage to deploy the air bag even after the battery
has been disconnected. Serious injury may result from unintended air bag deployment if work
is done on the SRS system immediately after the battery cable is disconnected.
(3) Warning labels must be heeded when servicing or handling SRS components. Warning labels
are located in the following locations.
DSun visor
DGlove box
DSRS-ECU
DSteering wheel
DSteering Joint Cover
DAir bag module (driver’s side and front passenger’s side)
DClock spring
DSeat belt with pre-tensioner
(4) Always use the designated special tools and test equipment.
(5) Store components removed from the SRS in a clean and dry place.
The air bag module should be stored on a flat surface and placed so that the pad surface is
facing upward.
Do not place anything on top of it.
(6) Never attempt to disassemble or repair the SRS components (SRS-ECU, air bag module, clock
spring and seat belt with pre-tensioner).
(7) Whenever you finish servicing the SRS, check the SRS warning lamp operation to make sure
that the system functions properly.
(8) Be sure to deploy the air bag before disposing of the air bag module or disposing of a vehicle
equipped with an air bag. (Refer to GROUP 52B - Air Bag Module Disposal Procedures.)
2. Observe the following when carrying out operations on places where SRS components are installed,
including operations not directly related to the SRS air bag.
(1) When removing or installing parts do not allow any impact or shock to the SRS components.
(2) SRS components should not be subjected to heat, so remove the SRS components before drying
or baking the vehicle after painting.
DSRS-ECU, air bag module, clock spring: 93_C or more
DSeat belt with pre-tensioner: 90_C or more
After re-installing them, check the SRS warning lamp operation to make sure that the system
functions properly.

GENERAL -Precautions Before ServiceGENERAL -Precautions Before Service00-20
MUT-II
Refer to the “MUT-IIREFERENCE MANUAL” or “MUT-II
OPERATING INSTRUCTIONS” for instructions on handling
the MUT-II.
Connect the MUT-IIto the diagnosis connector as shown
in the illustration.
Caution
Turn the ignition switch to the LOCK (OFF) position before
connecting or disconnecting the MUT-II.
IN ORDER TO PREVENT VEHICLES FROM FIRE
“Improper installation of electrical or fuel related parts could cause a fire. In order to retain the high
quality and safety of the vehicle, it is important that any accessories that may be fitted or modifications/repairs
that may be carried out which involve the electrical or fuel systems, MUST be carried out in accordance
with MMC’s information/Instructions”.
ENGINE OILS
Health Warning
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin,
leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful
contaminants which may cause skin cancer. Adequate means of skin protection and washing facilities
must be provided.
Recommended Precautions
The most effective precaution is to adapt working practices which prevent, as far as practicable, the
risk of skin contact with mineral oils, for example by using enclosed systems for handling used engine
oil and by degreasing components, where practicable, before handling them.
Other precautions:
DAvoid prolonged and repeated contact with oils, particularly used engine oils.
DWear protective clothing, including impervious gloves where practicable.
DAvoid contaminating clothes, particularly underpants, with oil.
DDo not put oily rags in pockets, the use of overalls without pockets will avoid this.
DDo not wear heavily soiled clothing and oil-impregnated foot-wear. Overalls must be cleaned regularly
and kept separately from personal clothing.
DWhere there is a risk of eye contact, eye protection should be worn, for example, chemical goggles
or face shields; in addition an eye wash facility should be provided.
DObtain First Aid treatment immediately for open cuts and wounds.
DWash regularly with soap and water to ensure all oil is removed, especially before meals (skin cleansers
and nail brushes will help). After cleaning, the application of preparations containing lanolin to replace
the natural skin oils is advised.
DDo not use petrol, kerosine, diesel fuel, gas oil, thinners or solvents for cleaning skin.
DUse barrier creams, applying them before each work period, to help the removal of oil from the skin
after work.
DIf skin disorders develop, obtain medical advice without delay.
MUT-II
sub-assembly
ROM pack
MUT-˜

GENERAL -Supplemental Restraint System (SRS)00-21
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
To improve safety, the SRS and seat belts with
pre-tensioner. These systems enhance collision
safety by restraining the front passengers in case
of an accident. The SRS works with the
pre-tensioner simultaneously when a collision is
detected.
The SRS consists of two air bag modules, SRS
air bag control unit (SRS-ECU), SRS warning lamp
and clock spring. The air bags are located in the
center of the steering wheel, above the glove box.
Each air bag has a folded air bag and an inflator
unit. The SRS-ECU under the floor console monitors
the system and has a safing G-sensor and an
analog G-sensor. The warning lamp on theinstrument panel indicates the operational status
of the SRS. The clock spring is installed in the
steering column. The seat belt pre-tensioner is built
into the front seat belt retractor. Only authorized
service personnel should do work on or around
the SRS components and seat belt with
pre-tensioner. Those service personnel should read
this manual carefully before starting any such work.
Extreme care must be used when servicing the
SRS to avoid injury to the service personnel (by
inadvertent deployment of the air bags or
inadvertent operation of the seat belt with
pre-tensioner) or the driver (by rendering the SRS
or the seat belt with pre-tensioner inoperative).
Diagnosis
connectorFront passenger’s
air bag module
Clock spring Driver’s air bag
module
SRS-ECU
SRS warning lamp
Driver’s air bag
Front
passenger’s
air bag
Seat belt with
pre-tensioner

GENERAL -Supplemental Restraint System (SRS)00-22
SRS SERVICE PRECAUTIONS
1. In order to avoid injury to yourself or others
from accidental deployment of the air bag and
accidental operation of the seat belt with
pre-tensioner during servicing, read and
carefully follow all the precautions and
procedures described in this manual.
2. Do not use any electrical test equipment on
or near SRS components, except those
specified on P.52B-6.
3. Never Attempt to Repair the Following
Components:
DSRS air bag control unit (SRS-ECU)
DClock spring
DDriver’s and front passenger’s air bag
modules
DSeat belt with pre-tensionerNOTE
If any of these components are diagnosed as
faulty, they should only be replaced, in
accordance with the INDIVIDUAL COM-
PONENTS SERVICE procedures in this
manual. (Refer to P.52B-49.)
4. After disconnecting the negative (–) battery cable,
wait 60 seconds at least before any service and
insulate the disconnected cable with tape. The SRS
retain enough voltage to deploy the air bags for a
short time even after the disconnection of the battery.
So, serious injury may result by accidental air bag
deployment if a work is done on the SRS just after
the disconnection of the battery.
5. Do not attempt to repair the wiring harness connectors
of the SRS. If the connector(s) are diagnosed as defective,
replace the wiring harness(es). If the harness(es) are
diagnosed as faulty, replace or repair the wiring
harness(es) according to the table that follows.
Insulating tape
Battery
SRS-ECU connector

GENERAL -Supplemental Restraint System (SRS)00-23
SRS-ECU
Terminal No.Destination of harnessCorrective action
7Instrument panel wiring harness→EarthRepair or replace each wiring
harness
8Instrument panel wiring harness→Combination meter
(SRS warning lamp)
harness
9, 10Instrument panel wiring harness→Front passenger’s air bag
module
11 , 1 2Instrument panel wiring harness→Clock spring→Driver’s air bag
module)Repair or replace the dash wiring
harness. Replace clock spring.
13Instrument panel wiring harness→Junction block (fuse No.3)Repair or replace each wiring
harness
16Instrument panel wiring harness→Junction block (fuse No.2)
harness.
20Instrument panel wiring harness→Diagnosis connector
29, 30Floor wiring harnessàDriver’s seat belt pre-tensioner
27, 28Floor wiring harnessàFront passenger’s seat belt pre-tensioner
6. Inspection of the SRS-ECU harness connector should be carried out by the following procedure.
Insert the special tool (probe, MB991222, in the harness set) into the connector from harness side
(rear side), and connect the tester to this probe. If any tool than specified is used, damage to the
harness and other components will result. Furthermore, measurement should not be carried out by
touching the probe directly against the terminals from the front of the connector. The terminals are
plated to increase their conductivity, so that if they are touched directly by the probe, the plating
may break, which will cause drops in reliability.
MB991222 SRS-ECU harness connector
SRS-ECU harness connector (rear view)
7. SRS components and seat belt with pre-tensioner should not be subjected to hart, so remove the
SRS-ECU, driver’s and front passenger’s air bag modules, clock spring, and seat belt with pre-tensioner
before drying or baking the vehicle after painting.
DSRS - ECU, air bag module, clock spring : 93Æ
or more
DSeat belt with pre-tensioner : 90Æ
or more
8. Whenever you finish servicing the SRS, check warning lamp operation to make sure that the system
functions properly. (Refer to P.52B-6.)
9. Make certain that the ignition switch is LOCK (OFF) position when the MUT-IIis connected or
disconnected.
10. If you have any questions about the SRS, please contact your local distributor.
NOTE
SERIOUS INJURY CAN RESULT FROM UNINTENDED AIR BAG DEPLOYMENT, SO USE ONLY
THE PROCEDURES AND EQUIPMENT SPECIFIED IN THIS MANUAL.