belt MITSUBISHI MONTERO 2000 Service Owner's Guide

GDI -Troubleshooting 13A-86
From the previouspage
OK
MUT-
IIData list
27 Power steering fluid pressure switch (Refer to P.13A-105.)NGCheck the power steering fluid pressure switch system. (Refer
to P.13A-102, Inspection procedure 30.)
OK
MUT-
IIData list
28 A/C switch (Refer to P.13A-105.)NGCheck the A/C switch and A/C relay system. (Refer to P.13A-102,
Inspection procedure 31.)
MUT-
IIData list
31 Small lampswitch (Refer to P.13A-105.)NGCheck the smalllampswitch system. (Refer to P.13A-104, Inspec-
tion procedure 33.)
OK
MUT-
IIData list
34 Air flow sensor reset signal (Refer to P.13A-105.)NGCheck the air flow sensor system. (Refer to P.13A-17, code No.
P0100.)
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-105.)NGCheck the EGR valve. (Refer to P.13A-60, code No. P0403.)
OK
Ye s
Clean around the throttle valve. (Refer to P.13A-220.)
No
NG
Check that the crankanglesensor andtiming beltcover are properly
installed.
OK
Check ignition coil spark for each cylinder.
(1) Remove the ignition coil.
(2) Install a new sparkplug to the removed ignitioncoil.
(3) Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
(4) Earth the sparkplug electrodesecurely.
(5) Check that the sparkplug igniteswhen theengine iscranked.NG
Replace the ignition coil.
OK
Check all the following items:
DSpark plugs
DCompression pressure
DForeign material (such as water or kerosine) entered the fuel
linesOK
Check ignition timing. (Refer to GROUP 11A - Engine Adjustment.)
Does theenginestall immediately after the acceleratorpedal is
released?


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-89
Inspection procedure 13
Hesitation, sag, stumble, poor acceleration or surge
Probable cause
The cause is probably a malfunction of the ignition system, electronic-controlled throttle
valve system, compression pressure, etc.DMalfunction of the ignition system
DMalfunction of the air/fuel ratio control system
DMalfunction of the electronic-controlled throttle valve
system
DImproper compression pressure
DAir stuck in the air intake system
MUT-
IISelf-Diag code
Is a diagnosis code displayed?Ye s(Refer to P.13A-15, INSPECTION CHART FOR DIAGNOSIS
CODES.)
OK
Check ignition timing. (Refer to GROUP 11A - Engine Adjustment.)NGCheck that the crankanglesensor andtiming beltcover are properly
installed.
OK
NG
Check the acceleratorpedal positionswitch. (Refer to P.13A-100,
Inspection procedure 28.)
OK
MUT-
IIData list
13 Intake air temperature sensor (Refer to P.13A-105.)NGCheck the intake air temperature sensor. (Refer to P.13A-21, code
No. P0110.)
OK
MUT-
IIData list
25 Barometric pressure sensor (Refer to P.13A-105.)NGCheck the barometric pressure sensor. (Refer to P.13A-19, code
No. P0105.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-105.)NGCheck theengine coolant temperaturesensor. (Refer to P.13A-22,
code No. P0115.)
OK
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-105.)NGCheck the throttle valve position feedback system. (Refer to
P.13A-65, code No. P1221.)
OK
MUT-
IIData list
11 Oxygen sensor (front)
OK:
0 - 400 mV and 600 - 1,000 mV alternates when the
engine is idling(wait for four minutes after theengine
started).NGMeasure fuel high-pressure between the fuel pump (highpressure)
and injector. (Refer to P.13A-224.)
OK
MUT-
IIData list
11 Oxygen sensor (front)
OK:
600 - 1,000 mV when theengine is suddenlyracedNGCheck the oxygen sensor (front) system. (Refer to P.13A-28, code
No. P0130.)
OK
Check that air is sucked in the air intake system.
DBroken intake manifold gasket
DDamaged vacuum hose
DDamaged air intake hose
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-105.)NGCheck the EGR valve. (Refer to P.13A-60, code No. P0403.)
OK
MUT-
IIActuator test
08 Purge control solenoid valve (Refer to P.13A-110.)NGCheck the purge control solenoid valve. (Refer to P.13A-62, code
No. P0443.)
OK
To the nextpage
OK
MUT-
IIData list
59 Oxygen sensor (rear) (Refer to P.13A-78.)
DTransmission: 2nd gear
DDriving with throttle widelyopen
OK:
600 - 1,000 mVNGCheck the oxygen sensor (rear) system. (Refer to P.13A-31, code
No. P0136.)
MUT-
IIData list
26 Acceleratorpedal positionswitch (Refer to P.13A-105.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-92
Inspection procedure 18
Too high CO and HC concentration when idling
Probable cause
The cause is probably an incorrect air/fuel ratioDMalfunction of air/fuel ratio control system
DDeterioration of the catalyst
MUT-
IISelf-Diag code
Is a diagnosis code displayed?Ye s(Refer to P.13A-15, INSPECTION CHART FOR DIAGNOSIS
CODES.)
No
Check ignition timing. (Refer to GROUP 11A - Engine Adjustment.)NGCheck that the crankanglesensor andtiming beltcover are properly
installed.
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-105.)NGCheck theengine coolant temperaturesensor. (Refer to P.13A-22,
code No. P0115.)
OK
MUT-
IIData list
13 Intake air temperature sensor (Refer to P.13A-105.)NGCheck the intake air temperature sensor. (Refer to P.13A-21, code
No. P0110.)
OK
MUT-
IIData list
25 Barometric pressure sensor (Refer to P.13A-105.)NGCheck the barometric pressure sensor. (Refer to P.13A-19, code
No. P0105.)
OK
NG
Check the oxygen sensor (front) system. (Refer to P.13A-31, code
No. P0130.)
OK
MUT-
IIData list
11 Oxygen sensor (front)
OK:
0 - 400 mV and 600 - 1,000 mV alternates when the
engine is idling(wait for four minutes after theengine
started).OKReplace the oxygen sensor (front).
Check trouble symptom.
NGNG
Measure fuel high-pressure between the fuel pump (highpressure)
and injector. (Refer to P.13A-224.)NG
Repair
OK
Check ignition coil spark for each cylinder.
(1) Remove the ignition coil.
(2) Install a new sparkplug to the removed ignitioncoil.
(3) Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is applied to the injector, or you are seriously injured.
(4) Earth the sparkplug electrodesecurely.
(5) Check that the sparkplug igniteswhen theengine iscranked.
NG
Replace the ignition coil.
OK
Check all the following items:
DSparkplug
DEGR system
DCompression pressure
DClogged fuel filter or line
OK
To the nextpage
OK
MUT-
IIData list
59 Oxygen sensor (rear) (Refer to P.13A-78.)
DTransmission: 2nd gear
DDriving with throttle widelyopen
OK:
600 - 1,000 mVNGCheck the oxygen sensor (rear) system. (Refer to P.13A-31, code
No. P0136.)
MUT-
IIData list
11 Oxygen sensor (front)
OK:
600 - 1,000 mV when theengine is suddenlyraced


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-171
Inspection procedure 5
No initial combustion (starting impossible)
Probable cause
In cases such as the above, the cause is probably that a sparkplug is
defective, or that the supply of fuel to the combustion chamber is defective.
In addition, foreign materials (water, kerosene, etc.) may be mixed with the fuel.DMalfunction of the fuel supply system
DMalfunction of the ignition system
DMalfunction of the engine-A/T-ECU
NGRepair
OK
MUT-
IIData list
22 Crankanglesensor (Refer to P.13A-198.)NGCheck the crankanglesensor system.
(Refer to P.13A-140, code No.22.)
YES
MUT-
IIActuator Test
07 Fuel pump(low pressure) (Refer to P.13A-203.)NGCheck fuelpump(low pressure) system
(Refer to P.13A-193, Inspection procedure 29.)
OK
Does the camshaft rotate when theengine is cranking?NOCheck if thetiming belt isbroken ordamaged.
NO
MUT-
IIData list
16 Battery voltage (Refer to P.13A-198.)NGCheck theengine controlrelay and ignition switch-IG system
(Refer to P.13A-190, Inspection procedure 25.)
OK
MUT-
IISelf-Diag Code
Is a diagnosis code set?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES
Check battery voltage when cranking.
OK:
8 V or higherNGCheck the battery.
OK
Is starting good if the engine iscranked with the accelerator
pedalslightly depressed?YESDClean the throttle valve area. (Refer to P.13A-220.)
DCheck and adjust the throttle position sensor (Refer to
P.13A-220.)
OK
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle position sensor (1st channel) system
(Refer to P.13A-158, code No.79.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system
(Refer to P.13A-138, code No.21.)
OK
Measure low fuel pressure between the fuelpump(low
pressure) and fuelpump (highpressure) (Refer to P.13A-222.)NGRepair
OK
To the nextpage
NO
Adjust the throttle position sensor (Refer to P.13A-220.)
NG
Measure at injector driver connector B-19
DDisconnect the connector, and measure at the harness
side.
DThe voltage between terminals 4, 12, 21 and earth
(Ignition switch: ON)
OK
Battery voltage
Check fuel leakage (Refer to P.13A-225.)OK
Check the injector driver system.
(Refer to P.13A-196, Inspection procedure 34.) NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-172
OK
Check the following items in that order.
DCheck the sparkplug
DCheck the compression pressure
DCheck if foreign materials (water, alcohol, etc.) got into
fuel.
OK
Clamp the leads of the ignition coil No.1 terminal with atiming
light pick-up in order. Does thetiming lightflash when the
engine iscranked?NOCheck the ignition coil (built-in power transistor) system (Refer
to P.13A-148, code No.44.)
From the previouspage
OK
Check the trouble symptoms.
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine is
cranked.NGReplace the ignition coil.
YES
Check the ignitiontimingwhen cranking.
OK:
approx. 5_BTDCNGCheck that the crankanglesensor andtiming beltcover are
properly installed.
Replace the injector.NG
Inspection procedure 6
Initial combustion but no complete combustion (starting
impossible), long time to start (hard starting)
Probable cause
In such cases as the above, the cause is probably that the spark plugs are
generating sparks by the spark are weak, or the initial mixture is not appropriate.DMalfunction of fuel supply system
DMalfunction of of fuel pressure control solenoid
valve
DMalfunction of the ignition system
DMalfunction of the electronic-controlled throttle
valve system
DMalfunction of the engine-A/T-ECU
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system (Refer
to P.13A-138, code No.21.)
OK
MUT-
IISelf-Diag Code
Is a diagnosis code set?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.
Check the battery voltage when cranking.
OK:
8 V or higherNGCheck the battery.
NO
MUT-
IIActuator Test
07 Fuel pump(low pressure) (Refer to P.13A-203.)NGCheck fuelpumpsystem (low-pressure)
(Refer to P.13A-193, Inspection procedure 29.)
OK
To the nextpage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-173
NGReplace the injector.Check the trouble symptoms.
OK
Check the following items in that order.
DCheck the sparkplug
DCheck the compression pressure
DCheck the fuel lines for clogging.
DCheck if foreign materials (water, alcohol, etc.) got into
fuel.
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
3. Disconnect the injector intermediate connector.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine is
cranked.NGReplace the ignition coil.
Check the ignitiontimingwhen cranking.
OK:
Approx. 5_BTDCNGCheck that the crankanglesensor andtiming beltcover are
installed properly.
NO
Adjust the throttle position sensor (Refer to P.13A-220.)
OK
Is starting good if the engine iscranked with the accelerator
pedalslightly depressed?YESDClean the throttle valve area. (Refer to P.13A-220)
DAdjust the throttle position sensor
(Refer to P.13A-220.)
OK
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle valve position feedback system.
(Refer to P.13A-162, code No.92.)
OK
Check fuel leakage. (Refer to P.13A-225.)NGRepair
OK
MUT-
IIActuator Test
74 Fuel pressure sensor (Refer to P.13A-203.)NGCheck abnormal fuel pressure.
(Refer to P.13A-151, code No.56.)
OK
MUT-
IIData list
18 Cranking signal (Refer to P.13A-198.)NGCheck the ignition switch-ST system and inhibitor switch
(Refer to 13A-191, Inspection procedure 27.)
From the previouspage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-175
OK
NG
Air is sucked in the air intake system, or EGR gas leaks.
DBroken intake manifold gasket
DDamaged air intake hose
DDamaged vacuum hose
DFaulty EGR valve seat
Check the trouble symptoms.
OK
Check the following items in that order.
DCheck the sparkplug
DCheck the exhaust gas emission control system
DCheck the EGR control system
DCheck the compression pressure
DCheck if foreign materials (water, kerosine,etc.) got into
fuel.
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine is
cranked.NGReplace the ignition coil.
Clean around the throttle valve. (Refer to P.13A-220.)
OK
Check the ignition timing. (Refer to GROUP 11A - Engine
Adjustment.)NGCheck that the crankanglesensor andtiming beltcover are
properly installed.
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-198.)NGCheck the EGR valve system (Refer to P.13A-196, Inspection
procedure 35.)
OK
MUT-
IIData list
14 Throttle position sensor (2nd channel)
After warming-up, let theengine run at idlingwith no load.
OK:
When idling, 3,900 - 4,800 mVNGDClean around the throttle valve. (Refer to P.13A-220)
DAdjust the throttle position sensor (Refer to P.13A-220.)
OK
MUT-
IIData list
67 Stoplampswitch (Refer to P.13A-198.)NGCheck the stoplampswitch system
(Refer to P.13A-195, Inspection procedure 32.)
OK
MUT-
IIData list
28 A/C switch (Refer to P.13A-198.)NGCheck the A/C switch and A/C relay system
(Refer to P.13A-194, Inspection procedure 31.)
OK
MUT-
IIData list
27 Power steering oil pressure switch (Refer to P.13A-198.)NGCheck the power steering oil pressure switch system (Refer to
P.13A-194, Inspection procedure 30.)
From the previouspage
OK
MUT-
IIData list
31 Small lampswitch (Refer to P.13A-198.)NGCheck the smalllampswitch system
(Refer to P.13A-195, Inspection procedure 33.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-177
Inspection procedure 9
When the engine is cold, it stalls at idling. (Die out)
Probable cause
In such cases as the above, the cause is probably that the air/fuel mixture is
inappropriate when theengine iscold, or that the intake air volume is
insufficient.DMalfunction of the electronic-controlled throttle
valve system
DMalfunction of the throttle body
OK
NG
Replace the injector.
Check the trouble symptoms.
Check the following items in that order.
DCheck the sparkplug
DCheck the compression pressure
DCheck theengine oilviscosity.
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine is
cranked.NGReplace the ignition coil.
OK
Check the ignition timing. (Refer to GROUP 11A - Engine
Adjustment.)NGCheck that the crankanglesensor andtiming beltcover are
properly installed.
NO
Measure fuel high-pressure between the fuel pump (high
pressure) and injector. (Refer to P.13A-222.)
OK
Does theenginestall right after the acceleratorpedal is
released?YESDClean around the throttle valve. (Refer to P.13A-220.)
DAdjust the throttle position sensor. (Refer to P.13A-220.)
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-198.)NGCheck the EGR valve system.
(Refer to P.13A-196, Inspection procedure 35.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system.
(Refer to P.13A-138, code No.21.)
OK
MUT-
IIData list
26 Acceleratorpedal positionswitch
(Refer to P.13A-198.)NGCheck the acceleratorpedal positionswitch system.
(Refer to P.13A-192, Inspection procedure 28.)
NO
MUT-
IIData list
14 Throttle position sensor (2nd channel) (Refer to P.13A-198.)NGCheck the throttle valve position feedback system.
(Refer to P.13A-162, code No.92.)
NO
Is engine-idling stable after the warming-up?YESCheck the unstableidling (rough, hunting).
(Refer to P.13A-174, Inspection procedure 7.)
NO
MUT-
IISelf-Diag Code
Is a diagnosis code set?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.
Has the batterybeen disconnectedrecently?YESAfter warming-up, let theengine run at idling for 10 minutes.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-179
OK
Check the following items in that order.
DCheck the sparkplug
DCheck the compression pressure
DCheck if foreign materials (water, kerosine,etc.) got into
fuel.
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-198.)NGCheck the EGR valve system (Refer to P.13A-196, Inspection
procedure 35.)
OK
MUT-
IIData list
28 A/C switch (Refer to P.13A-198.)NGCheck the A/C switch and A/C relay system
(Refer to P.13A-194, Inspection procedure 31.)
OK
MUT-
IIData list
27 Power steering oil pressure switch (Refer to P.13A-198.)NGCheck the power steering oil pressure switch system (Refer to
P.13A-194, Inspection procedure30.)
From the previouspage
NO
Check the ignition timing. (Refer to GROUP 11A - Engine
Adjustment.)OKCheck that the crankanglesensor andtiming beltcover are
properly installed.
NG
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine is
cranked.NGReplace the ignition coil.
OK
MUT-
IIData list
14 Throttle position sensor (2nd channel)
After warming-up, let theengine run at idlingwith no load.
OK:
3,900 - 4,800 mVNGDClean around the throttle valve. (Refer to P.13A-220)
DAdjust the throttle position sensor (Refer to P.13A-220.)
OK
MUT-
IIData list
34 Air flow sensor reset signal (Refer to P.13A-198.)NGCheck the air flow sensor system
(Refer to P.13A-133, code No.12.)
OK
Does theenginestall right after the acceleratorpedal is
released?YESClean around the throttle valve. (Refer to P.13A-220.)
OK
MUT-
IIData list
31 Small lampswitch (Refer to P.13A-198.)NGCheck the smalllampswitch system (Refer to P.13A-195,
Inspection procedure 33.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-182
Inspection procedure 13
Hesitation, sag, stumble, poor acceleration or surge
Probable cause
The cause is probably a malfunction of the ignition system, air/fuel ratio control
system, electronic controlled throttle valve system, compression pressure, etc.DMalfunction of the ignition system
DMalfunction of the air/fuel ratio control system
DMalfunction of the electronic-controlled throttle
valve system
DImproper compression pressure
DAir stuck in the air intake system
NO
NG
Check that the crankanglesensor andtiming beltcover are
properly installed.
OK
Check that air is sucked in the air intake system.
DBroken intake manifold gasket
DDamaged vacuum hose
DDamaged air intake hose
OK
To the nextpage
MUT-
IIData list
68 EGR valve (Refer to P.13A-198.)NGCheck the EGR valve system (Refer to P.13A-196, Inspection
procedure 35.)
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
0 - 400 mV and 600 - 1,000 mV alternates when
the engine is idling(wait for 2 minutes after the en-
gine is started).NGMeasure fuel high-pressure between the fuel pump (high
pressure) and injector. (Refer to P.13A-222.)
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
600 - 1,000 mV when theengine is suddenlyracedNGCheck the oxygen sensor system. (Refer to P.13A-131, code
No.11.)
OK
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle valve position feedback system (Refer to
P.13A-162, code No.92.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system (Refer
to P.13A-138, code No.21.)
OK
MUT-
IIData list
25 Barometric pressure sensor (Refer to P.13A-198.)NGCheck the barometric pressure sensor system (Refer to
P.13A-145, code No.25.)
OK
MUT-
IIData list
13 Intake air temperature sensor (Refer to P.13A-198.)NGCheck the intake air temperature sensor system (Refer to
P.13A-135, code No.13.)
OK
MUT-
IIData list
26 Acceleratorpedal positionswitch
(Refer to P.13A-198.)NGCheck the acceleratorpedal positionswitch system.
(Refer to P.13A-192, Inspection procedure 28.)
Check the ignition timing. (Refer to GROUP11A - Engine
Adjustment)
MUT-
IISelf-Diag Code
Is a diagnosis code displayed?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.
OK


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk