At mode MITSUBISHI MONTERO 2000 Service Workshop Manual

AUTOMATIC TRANSMISSION -Troubleshooting 23-20
Code No. 22 Input shaft speed sensor systemProbable cause
If no output pulse from the input shaft speed sensor is detected for 1 second or
more while the vehicle is driving at 30 km/h or more in 4th, it isjudged that
there is a short-circuit oropencircuit in the input shaft speed sensor, and code
No. 22 is output.
If code No. 22 is output 4 times, the transmission is locked at 3rd gear (D) or
2nd gear (downshift operation in Sports mode) as a fail-safe measure, and the N
range indicator lampflashes at 1 Hz.DMalfunction of input shaft speed sensor
DMalfunction of reverse clutch retainer
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK NG
Check the following connectors:
<6G7> D-121,<4M4>D-108
To the nextpage
NG
OKNG
NG
RepairCheck the following connectors:
<6G7> D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OKMUT-
IIData List
DNo. 22 Input shaft speed sensor
OK:Refer to P.23-61 (Data List
Chart).
Repair
OK
NG
NG
Check the trouble symptoms.
OK
Measure at engine-A/T-ECU
connector D-121 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7> Voltage between terminal
81 and earth
D<4M4> Voltage between terminal
43 and earth
OK:0.5 V or less
Replace the engine-A/T-ECU or
A/T-ECU. NGCheck the trouble symptoms.
NG
Check the trouble symptoms.
Check the following connectors:
<6G7> D-121, D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OK
OK
Measure at engine-A/T-ECU
connector D-122 <6G7>, or at
A/T-ECU connector D-108 <4M4>.
DMeasure at the ECU terminals
DDisconnect C-23
DIgnition switch: ON
D<6G7> Voltage between terminal
103 and earth
D<4M4> Voltage between terminal
31 and earth
OK:4.8 - 5.2 V
Measure the output wave pattern of
the input shaft speed sensor at
engine-A/T-ECU connectors D-121
and D-122 <6G7>, or at A/T-ECU
connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
D<6G7> Voltage between terminal
81 of D-121 and terminal 103 of
D-122
D<4M4> Voltage between terminal
31 of D-108 and terminal 43 of
D-108
OK:A wave pattern such as the
one shown on P.23-69
(Check Procedure Using an
Oscilloscope) should be
output, and the maximum
value should be 4.8 V or
more and the minimumval-
ue should be 0.8 V or less.
There should be no noise
in the output wave pattern.NG
NG
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-22
Code No. 23 Output shaft speed sensor systemProbable cause
If the output from the output shaft speed sensor is 50% or less continuously for
1 second or more while the vehicle is driving at 30 km/h or more in 4th, it is
judged that there is ashort-circuit oropencircuit in the output shaft speed
sensor, and code No. 23 is output.
If code No. 23 is output 4 times, the transmission is locked at 3rd gear (D) or
2nd gear (downshift operation in Sports mode) as a fail-safe measure, and the N
range indicator lampflashes at 1 Hz.DMalfunction of output shaft speed sensor
DMalfunction of direct planetary carrier
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NG
Repair
NG
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK NG
Check the following connectors:
<6G7> D-122,<4M4>D-108
To the nextpage
NG
OK
NG
RepairCheck the following connectors:
<6G7> D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OKMUT-
IIData List
DNo. 23 Output shaft speed
sensor system
OK:Refer to P.23-61 (Data List
Chart).
Repair
OK
OK
NG
Check the trouble symptoms.
OK
Measure at engine-A/T-ECU
connector D-121 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7>Voltage between terminals
81 and earth
D<4M4> Voltage between terminal
43 and earth
OK:0.5 V or less
Replace the engine-A/T-ECU or
A/T-ECU. NGCheck the trouble symptoms.
NG
Check the trouble symptoms.
Check the following connectors:
<6G7> D-121, D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OK
Measure at engine-A/T-ECU
connector D-122 <6G7>, or at
A/T-ECU connector D-108 <4M4>.
DMeasure at the ECU terminals
DDisconnect C-02
DIgnition switch: ON
D<6G7>Voltage between terminals
104 and earth
D<4M4> Voltage between terminal
32 and earth
OK:4.8 - 5.2 VNG
Measure the output wave pattern of
the output shaft speed sensor at
engine-A/T-ECU connectors D-121
and D-122 <6G7>, or at A/T-ECU
connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
D<6G7> Voltage between terminal
81 of D-121 and terminal 104 of
D-122
D<4M4> Voltage between terminal
32 of D-108 and terminal 43 of
D-108
OK:A wave pattern such as the
one shown on P.23-69
(Check Procedure Using an
Oscilloscope) should be
output, and the maximum
value should be 4.8 V or
more and the minimumval-
ue should be 0.8 V or less.
There should be no noise
in the output wave pattern.NG
Repair
NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-49
Inspection procedure 2
Starting not possible
Probable cause
If the enginewill not start when the selector lever is at the P or N position, the
cause is probably a malfunction of the inhibitor switch system, the transmission
control cable assembly, theenginesystem, the torque converter or the oil pump.DMalfunction of inhibitor switch system
DMalfunction of transmission control cable assembly
DMalfunction of enginesystem
DMalfunction of torque converter
DMalfunction of oil pump
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NG
Inspection Procedure 16: Inhibitor switch system check (Refer
to P.23-58.)NG
Repair or replace
OK
Torque converter check
DCheck for incorrect installation (inserted at an angle, etc.)
or damagedsplines.NGIf repair is possible, repair the damaged part.
If repair is not possible because the splines aredamaged,
replace the torque converter assembly.
OK
Replace the oil pumpassembly.
L
(The oilpump cannot be disassembled.)
Engine system check
DControl system, ignition system, fuel system, vehicle bodyNG
Repair
OK
Transmission control cable assembly checkNG
Repair OK
Check the trouble symptoms.Replace the engine-A/T-ECU or A/T-ECU.
Inspection procedure 3
Does not move forward
Probable cause
If the vehicle does not move forward when theengine is idling and theselector
lever is moved from N to D, 3, 2 or L, or if it is shifted to 1st or 2nd in Sports
mode, the cause is probably a problem with line pressure, or a malfunction of
the UD clutch or valve body.DAbnormal line pressure
DMalfunction of UD solenoid valve
DMalfunction of UD clutch system
DMalfunction of valve body
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
MUT-
IIActuator Test
DNo.2 UD solenoid valve
OK:Sound of operation can be heardNGReplace the solenoid valve.
L
OK
Fluid pressure test (Refer to P.23-106.)
DMeasure the fluid pressure at each element in 1st in
Sportsmode
Standard value:Refer to P.23-106.NGDisassemble, clean and re-assemble the valve body.
L
DMake sure that the mounting bolts are not loose and that
the O-ring and valve body are notdamaged or positioned
incorrectly.
DIf the extent of thedamagelooks too bad for repairs to be
carried out, replace the valve body assembly.
OK
UD clutch system check
DRemove the transmission assembly, the valve body cover
and the valve body.
DBlow air through the UD clutch oilhole in the transmission
case, and check that the piston operates to maintain
pressure.
UD clutch check
L
DCheck for a problem such as burnt facing, poor piston
sealing or interference with the retainer.OKCheck the trouble symptoms. NG
Replace the engine-A/T-ECU or A/T-ECU.NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-61
DATA LIST REFERENCE TABLE
Data
list No.Check itemInspection conditionsNormal condition
11APSIgnition switch: ON
Engine: StoppedAccelerator pedal:
Fully closed985 - 1085 mV
Engine: Stopped
Selector lever posi-
tion: P
Accelerator pedal:
DepressedGradually increases from the above
value.
Accelerator pedal:
Fully open4000 mV or higher
15A/T fluid tempera-
ture sensorDriving after en-
gine has warmed
upDrive for 15 minutes
or more until the ATF
temperature reaches
70 - 80°C.Gradually increases to 70 - 80°C.
21Crank angle sen-
sor <6G7>Engine: Idling
Selector lever posi-Compare the engine
speeds displayed onIdentical
sor <6G7>
Engine speed sen-
sor <4M4>Selector lever posi-
tion: Pspeeds displayed on
the tachometer and
the MUT-II.
22Input shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
23Output shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
25Wide open throttleAccelerator pedalReleasedOFF
switchpositionDepressedON
26Stop lamp switchIgnition switch: ON
Engine: StoppedBrake pedal: De-
pressedON
Engine: Stopped
Brake pedal: Re-
leasedOFF
29Vehicle speed sen-
sorSelector lever posi-
tion: Sports modeIdling in 1st
(Vehicle stopped)0 km/h
Driving at a constant
speed of 50 km/h in
3rd50 km/h
31LR solenoid valve
duty ratioSelector lever posi-
tion: Sports modeData List No.No. 31No. 32No. 33No. 34No.35
32UD solenoid valve
duty ratioDriving at a constant
speed in 1st0%0%100%100%0%
332nd solenoid valve
duty ratioDriving at a constant
speed in 2nd100%0%0%100%0%
34OD solenoid valve
duty ratioDriving at a constant
speed in 3rd100%0%100%0%0%
35RED solenoid
valve duty ratioDriving at a constant
speed in 4th0%0%100%0%100%
Driving at a constant
speed in 5th100%100%0%0%100%


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-62
Data
list No.Normal condition Inspection conditions Check item
36DCC solenoid
valve duty ratioShift range: 2ndDriving at 30 km/h in
2 range, then fully
close accelerator.70% - 90% -to- 0%
Driving at 50 km/h in
4th70% - 90%
52Damper clutch slip
amountShift range: 2ndDriving at 30 km/h in
2 range, then fully
close accelerator.- 300 - 100 r/min or 100 - 300 r/min
Driving at a constant
speed of 50 km/h in
4th- 10 - 10 r/min
54Control relay out-
put voltageIgnition switch:
OFFIgnition switch: ON10 - 12 V
61Inhibitor switchIgnition switch: ON
Engine: StoppedSelector lever posi-
tion: PP
Engine: Stopped
Selector lever posi-
tion: RR
Selector lever posi-
tion: NN
Selector lever posi-
tion: DD
63Shift positionSelector lever posi-
tion:
Sports modeDriving at a constant
speed of 10 km/h in
1st1st
Driving at a constant
speed of 30 km/h in
2nd2nd
Driving at a constant
speed of 50 km/h in
3rd3rd
Driving at a constant
speed of 50 km/h in
4th4th
Driving at a constant
speed of 70 km/h in
5th5th
65Dual pressureEngine: IdlingA/C switch: ONON
switchA/C switch: OFFOFF
66OD-OFFsignal
control is operatingWhile driving on a
level roadOFF
auto-cruise control
system>While climbing an
inclineON


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-63
Data
list No.Normal condition Inspection conditions Check item
67Select switchIgnition switch: ON
Engine: Stopped(Data List No. )No.
67No.
68No. 69
Engine: Stopped
Selector lever posi-
tion: DOFFOFFOFF
68Upshift switchSelector lever opera-
tion: Sports mode
selectedONOFFOFF
69Downshift switchSelector lever opera-
tion: Lever moved to
upshift position and
heldONONOFF
Selector lever opera-
tion: Lever moved to
downshift position
and heldONOFFON
73Target effective en-
gine pressure
<6G7>Engine: Idling
Selector lever posi-
tion: NAccelerator pedal:
fully closed to de-
pressedData changes.
754LLc switchIgnition switch: ON
Engine: StoppedTransfer lever posi-
tion: 4LLcON
Transfer lever posi-
tion:
Other than the aboveOFF
76Theoretical effec-
tive engine pres-
sure
<4M4>Engine: Idling
Selector lever posi-
tion: NAccelerator pedal:
fully closed to de-
pressedData changes.
ACTUATOR TEST TABLE
Item No.Check itemTest contentsInspection conditionsNormal condition
1LR solenoid valveThe solenoid valveIgnition switch: ONThe sound of opera-
2UD solenoid valvespecified by the MUT-Selector lever posi-tion should be heard
32nd solenoid valve
IIis driven at 50%
duty for 5 seconds. Notion: P
Engine: Stoppedwhen the solenoid
valve is driven.
4OD solenoid valveother solenoid valvesEngine: Stopped
Throttle (accelerator)
5RED solenoid valve
are energised.Opening angle volt-
6DCC solenoid valveage: Less than 1 V
<6G7>,
71st shift indicator lampThe indicator lamp for
<6G7>,
less than 1.2 V <4M4>
The shift indicator
82nd shift indicator lampthe shift stage speci-The fail-safe function
should not be operat-lamp illuminates.
93rd shift indicator lamp
fied by the MUT-II
illuminates for 3 sec-should not be operat-
ing.
104th shift indicator lamponds.
115th shift indicator lamp
12A/T control relayThe A/T control relay
turns off for 3 sec-
onds.Data List No. 54
(1) During test: 0 V
(2) Normal: System voltage
(V)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting AUTOMATIC TRANSMISSION -Troubleshooting 23-65
Ter-
minal
No.Standard value Inspection conditions Check item
1062nd solenoid valveEngine: Idling
Shift range: 2ndSystem voltage
Engine: Idling
Shift range: Park7–9 V
107DCC solenoid valveEngine: Idling
Shift range: 1stSystem voltage
108Inhibitor switch REngine: Idling
Selector lever position: RSystem voltage
Engine: Idling
Shift range: Other than the above0V
109Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
11 0Downshift switchIgnition switch: ON
Selector lever operation: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
11 24LLc switchIgnition switch: ON
Transfer lever position: 4LLcSystem voltage
Ignition switch: ON
Transfer lever position: Other than the above0V
11 5Wide open throttle switchAccelerator pedal: ReleasedSystem voltage
Accelerator pedal: Depressed0V
11 73rd shift indicator lampShift range: 3rdSystem voltage
Shift range: Other than the above0V
11 82nd shift indicator lampShift range: 2ndSystem voltage
Shift range: Other than the above0V
11 9RED solenoid valveEngine: Idling
Shift range: 5thSystem voltage
Engine: Idling
Shift range: Park7-9V
120UD solenoid valveEngine: Idling
Shift range: 1stSystem voltage
Engine: Idling
Shift range: Park7-9V
121Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
122Upshift switchIgnition switch: ON
Selector lever operation: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
123Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-68
Ter-
minal
No.Standard value Inspection conditions Check item
54Input communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D
55Inhibitor switch PIgnition switch: ON
Selector lever position: PSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
56Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
57Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
58Downshift switchIgnition switch: ON
Selector lever position: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
59Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V
62DIR solenoid valveEngine: Idling
Shift range: ParkSystem voltage
Engine: Idling
Shift range: 2nd7-9V
65Wide open throttle switchAccelerator pedal: Released4.5 - 5.5 V
Accelerator pedal: DepressedLess than 0.4 V
66Inhibitor switch RIgnition switch: ON
Selector lever position: RSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
67Inhibitor switch DIgnition switch: ON
Selector lever position: DSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
68Upshift switchIgnition switch: ON
Selector lever position: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
69Vehicle speed sensorWhen stopped0V
When starting to drive forward slowly.0 V and 5 V alter-
nates
71A/T control relayIgnition switch: OFF0V
Ignition switch: ON10 - 12 V
72EarthIgnition switch: ON0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

PROPELLER SHAFT
Click on the applicable bookmark to selected the required model year.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

FRONT AXLE
Click on the applicable bookmark to selected the required model year.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk