change time MITSUBISHI OUTLANDER SPORT 2014 3.G User Guide

Multi information display6-6 Instruments and controls
6
E00520701918
When the operation mode is put in ON, the display screen switches in the following order.1-
Tripmeter
m P. 6-10
2-
Tripmeter
m P. 6-10
3- ECO score display
m P. 6-14
4- Prediction charging time
m P. 3-8
5- Service reminder
m P. 6-11
6- Redisplay of a warning display screen
m P. 6-8
Information screen (when the operatio
n mode is changed from OFF to ON)
*:When the inspection time has arrived1- Screen when the operation mode is OFF2- System check screen
m P.6-12
3- Screen when the operation mode is ON4- Service reminder
m P.6-11
*
BK0203201EN.book 6 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-11
6
To r e t u r n t h e d i s p l a y t o 0 , h o l d d o w n t h emulti information display switch for about 2seconds or more. Only the currently dis-played value will be reset.ExampleIf tripmeter is displayed, only tripmeter
will be reset.
E00522502021
Displays the approximate time until the nextperiodic inspection recommended by
MITSUBISHI MOTORS. “---” is displayedwhen the inspection time has arrived.
1. Displays the time until the next periodicinspection.2. This informs you that a periodic inspec-tion is due. We recommend you to consulta MITSUBISHI MOTORS AuthorisedService Point.At that time, when the operation mode ischanged from OFF to ON, the warningdisplay is displayed for a few seconds onthe information screen.3. After your vehicle is inspected at aMITSUBISHI MOTORS Authorised Ser-vice Point, it displays the time until thenext periodic inspection.
The “---” display can be reset while the oper-ation mode of the power switch is in OFF.
Example usage of tripmeter and tripmeter
It is possible to measure two currentlytravelled distances, from home using trip-meter and from a particular point onthe way using tripmeter .
To r e s e t t h e t r i p m e t e r
NOTE
zWhen disconnecting the auxiliary battery ter-minal, the memory of tripmeter and are cleared, and the display returns to “0”.
Service reminder
NOTE
zDepending on the vehicle specifications, thedisplayed time may differ from the next peri-odic inspection time recommended byMITSUBISHI MOTORS.In addition, the display settings for the nextperiodic inspection time can be modified.To modify the display settings, have itadjusted at a MITSUBISHI MOTORSAuthorised Service Point.For more details, consult a MITSUBISHIMOTORS Authorised Service Point.
NOTE
zThe distance is show
n in units of 100 km
(100 miles). The time is
shown in units of
months.
To r e s e t
BK0203201EN.book 11 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-12 Instruments and controls
6
When the display is reset, the time until thenext periodic inspection is displayed and thewarning display is no longer displayed whenthe operation mode is changed from OFF toON.1. When you lightly press the multi informa-tion display switch a few times, the infor-mation screen switches to the servicereminder display screen.2. Press and hold the multi information dis-play switch for about 2 seconds or more todisplay “ ” and make it flash. (If there isno operation for about 10 seconds withflashing, the display returns to the previ-ous screen.)
3. Lightly press the multi information dis-play switch while the icon is flashing tochange the display from “---” to“CLEAR”. After this, the time until thenext periodic inspection will be displayed.
E00531001038
When the operation mode is put in ON, thesystem check screen is displayed for about 4seconds. If there is no fault, informationscreen (when the operation mode is ON) isdisplayed.If there is a fault, the screen changes to warn-ing display.Refer to “Warning display list” on page 6-22.
CAUTIONzThe customer is responsible for making surethat periodic inspection and maintenance areperformed.Inspections and maintenance must be per-formed to prevent accidents and malfunc-tions.NOTE
z“---” display cannot be reset when the opera-tion mode is in ON.zWhen “---” is displayed, after a certain dis-tance and a certain period of time, the dis-play is reset and the time until the nextperiodic inspection is displayed.
zIf you accidentally reset the display, we rec-ommend you to consult a MITSUBISHIMOTORS Authorised Service Point.
System check screen
NOTE
zThe system check screen display variesdepending on the customer’s equipment.NOTE
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-13
6
E00537600026
This displays the approximate driving range(how many more kilometres or miles you candrive).EV cruising range display (A)This displays the distance that can be traveledwith the remaining power in the drive battery.To t a l c r u i s i n g r a n g e d i s p l a y ( B )This displays the distance that can be traveledwith the remaining power in the drive batteryand the remaining amount of fuel.
E00531201072
This displays the average fuel consumptionfrom the last reset to the present time.There are the following 2 mode settings.Refer to “Changing the reset mode for aver-age fuel consumption” on page 6-16.For information on how to change the aver-age fuel consumption display setting, refer to“Changing the function settings” on page6-15.
EV cruising range display/Total cruising range display
NOTE
zThe driving range may vary depending onthe driving conditions
and habits. Treat the
distance displayed as just a rough guideline. zWhen the drive battery is charged or thevehicle is refueled, th
e cruising range display
is updated. However, if the charge level islow or the refueling amount is small, it can-not be updated correctly. Fully charge thebattery or refill to full tank whenever possi-ble.
zOn rare occasions, the value displayed forthe driving range may change if you areparked on an extremely steep incline. This isdue to the movement of fuel in the tank anddoes not indicate any malfunction.zThe display setting can be changed to thepreferred units (km or miles).Refer to “Changing the function settings” onpage 6-15.zWhen the EV cruising range falls belowapproximately 1 km (1 mile), the EV cruis-ing range display shows “---”.zWhen the total cruising range falls belowapproximately 50 km (30 miles), the totalcruising range disp
lay shows “---”.
Av e r a g e f u e l c o n s u m p t i o n d i s -play
NOTE
NOTE
zThe average fuel consumption display can bereset separately for the auto reset mode andfor the manual reset mode.z“---” is displayed when the average fuel con-sumption cannot be measured or when it is99.9 L/100 km (99.9 miles) or more.zThe initial (default) setting is “Auto resetmode”.zThe average fuel consumption will dependon the driving conditions (road conditions,how you drive, etc.). The displayed fuel con-sumption may vary from the actual fuel con-sumption. Treat the fuel consumptiondisplayed as just
a rough guideline.
zThe memory of the auto reset mode or man-ual reset mode for the average fuel consump-tion display is erased if the auxiliary batteryis disconnected.zThe display setting can be changed to thepreferred units {km/L, mpg (US), mpg (UK)or L/100 km}.Refer to “Changing the function settings” onpage 6-15.
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-16 Instruments and controls
6
4. Select the item to change on the menuscreen and change to the desired setting.Refer to the following items for furtherdetails on the operation methods.Refer to “Changing the reset mode foraverage fuel consumption” on page 6-16.Refer to “Changing the fuel consumptiondisplay unit” on page 6-17.Refer to “Changing the temperature unit”on page 6-17.Refer to “Changing the display language”on page 6-18.Refer to “Changing the language coopera-tive control” on page 6-18.Refer to “Operation sound setting” onpage 6-19.Refer to “Changing the time until “RESTREMINDER” is displayed” on page 6-19.Refer to “Changing the turn-signal sound”on page 6-20.Refer to “Returning to the factory set-tings” on page 6-20.
E00522902054
The mode conditions for the average fuelconsumption display can be switchedbetween “Auto reset” and “Manual reset”.1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “AVG (average fuelconsumption)”.
3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from A/1 (Auto reset mode) toM/2/P (Manual reset mode), or fromM/2/P to A/1.The setting is changed to the selectedmode condition.zWhen the average fuel consumption isbeing displayed, if you hold down themulti information display switch, theaverage fuel consumption displayed atthat time is reset.zWhen the operation mode is changedfrom ACC or OFF to ON, the mode set-ting is automatically switched from man-ual to auto.Switching to auto occurs automatically. Ifswitching to manual mode is done, how-ever, the data from the last reset is dis-played.zWhen the average fuel consumption isbeing displayed, if you hold down themulti information display switch, theaverage fuel consumption displayed atthat time is reset.
NOTE
zIf the auxiliary battery is disconnected, thesefunction settings are reset from memory andis automatically to the factory settings.
Changing the reset mode for aver-age fuel consumption
Manual reset modeAuto reset mode
BK0203201EN.book 16 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-19
6
2. Lightly press the multi information dis-play switch to select “ ” (languagecooperative control).3. Press and hold the multi information dis-play switch to switch from A (languagecooperation enabled) to M (languagecooperation disabled), or from M to A.The setting is changed to the selected con-dition.
E00523400690
Yo u c a n t u r n o f f t h e o p e r a t i o n s o u n d s o f t h emulti information display switch and rheostatillumination button.
1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “ ” (operationsound setting).3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from ON (operation sound on) toOFF (operation sound off), or from OFFto ON.The setting is changed to the selected con-dition.
E00523501702
The time until the display appears can bechanged.
NOTE
zThe language display modified with the lan-guage setting can be switched in the follow-ing manner.
•When A (language
cooperation enabled)
has been selected with the language cooper-ative control, the language for theBluetooth
®2.0 interface (if so equipped) is
automatically changed to the languageselected for the multi information display.However, this changing function may notwork depending on the language selectedfor the multi information display.•When M (language c
ooperation disabled)
has been selected with the language cooper-ative control, the language for theBluetooth
®2.0 interface (if so equipped) is
not automatically changed to the languageselected for the multi information display.
zThe language on the disp
lay of the audio sys-
tem (if so equipped) is not automaticallychanged even if you
select A (language
cooperation enabled) of
the language cooper-
ation control.
Operation sound setting
NOTE
NOTE
zThe operation sound setting only deactivatesthe operation sound of the multi informationdisplay switch and rheostat illumination but-ton. The warning di
splay and other sounds
cannot be deactivated.
Changing the time until “REST REMINDER” is displayed
BK0203201EN.book 19 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-20 Instruments and controls
6
1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “ALARM” (rest timesetting).3. Press and hold the multi information dis-play switch for about 2 seconds or more todisplay “ALARM”.4. Lightly press the multi information dis-play switch to select the time until the dis-play.5. Press and hold the multi information dis-play switch for about 2 seconds or more,the setting is changed to the selected time.
E00529100396
It is possible to change the turn-signal sound.
1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select (changing theturn-signal sound).3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from 1 (turn-signal sound 1) to 2(turn-signal sound 2), or from 2 to 1.The setting changes to the selected turn-signal sound.
E00523601875
All of the function settings can be returned totheir factory settings.1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “RESET” (returningto the factory settings).
3. When you press and hold the multi infor-mation display switch for about 5 secondsor more, the buzzer sounds and all of thefunction settings are returned to the fac-tory settings.
NOTE
zThe drive time is reset when the operationmode of the power switch is put in OFF.
Changing the turn-signal sound
Returning to the factory settings
NOTE
zThe factory settings
are as follows.
•Average fuel consum
ption reset mode: A
(Auto reset)•Fuel consumption display unit: L/100 km•Temperature unit: °C (Celsius)•Display language: ENGLISH or RUSSIAN•Cooperative language
setting: A (language
cooperation enabled)•Operation sounds: ON
(Operation sounds
on)•“REST REMINDER” display: OFF•Turn-signal sound: Turn-signal sound 1
BK0203201EN.book 20 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamps6-36 Instruments and controls
6
The setting for rest interval can be changed.
E00501600100E00501701427
These indicator lamps blink inthe following situations.zWhen the turn-signal leveris moved to activate a turn-signal lamp.
Refer to “Turn-signal lever” on page 6-45.
zWhen the hazard warning flasher switchis pressed to activate the hazard warninglamps.Refer to “Hazard warning flasher switch”on page 6-45.
Screen
Solution
We r e c o m m e n d y o u t o h a v e i t c h e c k e d . R e f e r t o “ S e r v i c e r e m i n d e r ” f o r f u r t h e r d e t a i l s o n p a g e 6-11.
Screen
Solution
Stop the vehicle in a safe place, stop the Plug-in Hybrid EV system, and take a rest.Use this display as rough guide for taking rests during a long drive.The interval from the start of your trip until this message is displayed can be set.Refer to “Changing the time until “REST REMINDER” is displayed” on page 6-19.The display and buzzer alert the driver when the set time is reached. If you continue to drive without having a rest, the buzzer sounds about every 5 minutes to encourage you to take a rest.zIn the following cases, the time driven is reset and the display returns to the previous dis-play screen. After this, when the set time is reached again, the buzzer and display encourage you to take a rest.•The buzzer sounds 3 times.•Put the operation mode in OFF.• The multi information display switch is held for about 2 seconds or more.
Indicator lamps Tu r n - s i g n a l i n d i c a t o r lamps/Hazard warning indica-tor lamps BK0203201EN.book 36 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Combination headlamps and dipper switch6-42 Instruments and controls
6
zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will turn off automaticallywhen the driver"s door is opened.zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will remain on for about 3 min-utes while the driver’s door is shut andwill then automatically turn off.
1. Turn the lamp switch in the “OFF” posi-tion while the operation mode of thepower switch is in OFF or ACC.2. Turn on the lamps with the switch in the“ ” or “ ” position again, then thelamps will remain on.3. When 1 minute has passed, the lamps willautomatically be turned off.
E00506101631
If the driver’s door is opened when the opera-tion mode of the power switch is put in ACCor OFF with the lamps illuminated, a buzzerwill sound to remind the driver to turn off thelamps.The buzzer will automatically stop if theauto-cutoff function is activated, the lampswitch is turned off, or the door is closed.
E00506201544
When the lamp switch is in the “ ” posi-tion, the beam changes from high to low (orlow to high) each time the lever is pulledfully (1). While the high beam is on, the highbeam indicator lamp in the instrument clusterwill also illuminate.
E00506300199
The high beams flash when the lever is pulledslightly (2), and will go off when it isreleased.When the high beam is on, the high beamindicator lamp in the instrument cluster willilluminate.
Lamps (headlamps, fog lamp, etc.) auto-cutout function
NOTE
zThe lamp auto-cutout function can also bedisabled.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
When you want to keep the lamps on:
NOTE
zIf you place the light switch in the “ ”position, the lamps will not be automaticallyturned off.
Lamp monitor buzzer
Dipper (High/Low beam change) Headlamp flasher
BK0203201EN.book 42 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Headlamp levelling6-44 Instruments and controls
6
E00517400103E00517500612
The direction of the headlamp beam (thedirection which the light shines in) altersaccording to the number of people and theload in the vehicle. Lower the headlamp
angle if it is too high due to the number ofpeople and/or the load in the vehicle so thatthe headlamps’ glare does not distract thedrivers of approaching vehicles. First set thelight switch to the “ ” position, then turnthe headlamp levelling switch knob to lowerthe beam. The greater the number on theheadlamp levelling switch knob, the lowerthe beam will point.Set the switch to the appropriate position sothat the headlamp beam is level with the road.
E00517601551
This mechanism automatically adjusts thedirection of the headlamps (beam position)depending on changes in the condition of thevehicle, such as the number of occupants orluggage weight. When the headlamps are illu-minated with the operation mode in ON, thebeam position of the headlamps is automati-cally adjusted when the vehicle is stopped.
•Turn the combination headlamps and dip-per switch to the “ ” or “ ” position.•Put the operation mode in ON.zIt is possible to modify
functions as follows:
•The time that the headlamps remain on canbe changed.•The coming home light function can bedeactivated.For further informati
on, please contact your
MITSUBISHI MOTORS Authorised ServicePoint.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
Headlamp levelling Headlamp levelling switch
*
Except for vehicles with discharge headlamps

NOTE
CAUTIONzAlways perform adjust
ments before driving.
Do not attempt to adjust while driving, as itcould cause an accident.
NOTE
zStart adjusting when the knob is at the “0”position (when the beam
is at its highest).
zKeep the knob in the “0” position exceptwhen using the knob to lower the headlampbeam angle.zAlways return the knob to the “0” positionwhen the baggage is removed and the peoplehave left the vehicle.
Automatic headlamp levelling
*
Ve h i c l e s w i t h d i s c h a r g e h e a d l a m p s

BK0203201EN.book 44 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分