lock MITSUBISHI PAJERO IV 2011 User Guide

Keys
E00300102038
The key fits all locks.Type 1
Type 2 WARNING
l When taking a
key on flights, do not
press any switches on the key while on
the plane. If a switch is pressed on the
plane, the key emits electromagnetic
waves, which could adversely affect the
plane’s flight operation.
When carrying a key in a bag, be careful
that no switches on the key can be easily
pressed by mistake.
NOTE l The
key number

is stamped on the tag as in-
dicated in the illustration.
Make a record of the key number and store
the key and key number tag in separate pla-
ces, so that you can order a key in the event
the original keys are lost.
l The key is a precision electronic device with
a built-in signal transmitter. Please observe
the following in order to prevent damage.
• Do not leave where it may be exposed toheat caused by direct sunlight, such as on
top of the dashboard.
• Do not take the remote control transmit- ter apart.
• Do not excessively bend the key or sub- ject it to strong impacts.
• Keep the remote control transmitter dry.
• Keep away from magnetic objects such as key rings.
• Keep away from devices that produce magnetism, such as audio systems, com-
puters and televisions.
• Do not clean with ultrasonic cleaners. • Do
not leave the key where it may be ex-
posed to

high temperature or high humid-
ity.
l The engine is designed so that it will not
start if the ID code registered in the immobil-
izer computer and the key’s ID code do not
match. Refer to the “Electronic immobilizer”
section for details and key usage. Locking and unlocking
1-02
1

OBKE12E1

Electronic immobilizer (Anti-
theft starting system) E00300201423
The electronic immobilizer
is designed to signifi-
cantly reduce the possibility of vehicle theft. The
purpose of the system is to immobilize the vehicle
if an invalid start is attempted. A valid start attempt
can only be achieved by using a key “registered” to
the immobilizer system.
NOTE
l In the following cases, the vehicle may not
be able to receive the registered ID code
from the registered key and the engine may
not start.
• When the key contacts a key ring or othermetallic or magnetic object (Type A)
• When the key grip contacts metal of an- other key (Type B) • When
the key contacts or is close to other
immobilizing keys
(including keys of oth-
er vehicles) (Type C)

In cases like these, remove the object or
additional key from the vehicle key. Then
try again to start the engine. If the engine
does not start, we recommend you to con-
tact your MITSUBISHI MOTORS Au-
thorized Service Point. l
Electronic immobilizer
is not compatible
with remote starting systems. Use of these sys-
tems may result in vehicle starting problems
and a loss of security protection.
l If you lose your key, order a key from your
MITSUBISHI MOTORS Authorized Service
Point as soon as possible. To obtain a replace-
ment or extra spare key, take your vehicle
and all remaining keys to your MITSUBISHI
MOTORS Authorized Service Point. All the
keys have to be re-registered in the immobil-
izer computer unit. The immobilizer can reg-
ister up to 8 different keys for use. CAUTION
l
Don’t make
any
alterations or additions
to the immobilizer system; alterations or
additions could cause failure of the immo-
bilizer. Locking and unlocking
1-03 1

OBKE12E1

Keyless entry system*
E00300302085
Press the remote
control switch, and all doors (in-
cluding the backdoor) will be locked or unlocked
as desired. It is also possible to operate the outside
rear-view mirrors. 1- LOCK switch
2- UNLOCK switch
3-
Indication lamp
To lock
Press

the LOCK switch (1), and all doors (includ-
ing the backdoor) will be locked. When they are
locked with the room lamp switch at the middle po-
sition (DOOR), the room lamp and the turn-signal
lamps blink once.
To unlock
Press the UNLOCK switch (2), and all doors (in-
cluding the backdoor) will be unlocked. When they
are unlocked with the room lamp switch at the mid-
dle position (DOOR), the room lamp will be turned
on for approximately 15 seconds and the turn-sig-
nal lamps will blink twice. NOTE
l The
indication lamp

(3) comes on each time
a switch is pressed.
l If the UNLOCK switch (2) is pressed and no
door (including the backdoor) is opened with-
in approximately 30 seconds: relocking will
automatically occur.
l It is possible to modify functions as follows:
For further information, please contact your
MITSUBISHI MOTORS Authorized Service
Point.
• The time for automatic relocking can bechanged.
• The confirmation function (blinking of the turn-signal lamps) can be set to oper-
ate only when the doors and backdoor are
locked or only when the doors and back-
door are unlocked.
• The confirmation function (this indicates locking or unlocking of the doors and
backdoor with the blink of the turn-signal
lamps) can be deactivated.
• The number of times the turn-signal lamps are flashed by the confirmation
function can be changed.
Operation of the outside rear-view mir-
rors
To fold
Within 30 seconds of locking the doors and back-
door using the LOCK switch (1), press the LOCK
switch twice rapidly to fold the outside rear-view
mirrors. To extend
Within 30 seconds

of unlocking the doors and back-
door using the UNLOCK switch (2), press the UN-
LOCK switch twice rapidly to return the outside
rear-view mirrors to their extended positions.
NOTE
l The keyless entry system does not operate in
the following conditions:
• The key is left in the key cylinder.
• The door (including the backdoor) is open.
l The remote control switch will operate with-
in approximately 4 m from the vehicle. How-
ever, the operating range of the remote con-
trol switch may change if the vehicle is loca-
ted near a power station, or radio/TV broad-
casting station.
l If either of the following problems occurs,
the battery may be exhausted.
• The remote control switch is operated atthe correct distance from the vehicle, but
the doors (including the backdoor) are
not locked/unlocked in response.
• The indication lamp (3) is dim or does not come on.
For further information, please contact
your MITSUBISHI MOTORS Author-
ized Service Point. If you replace the bat-
tery yourself, refer to “Procedure for re-
placing the remote control switch bat-
tery” on page 1-05.
l If your remote control switch is lost or dam-
aged, please contact your MITSUBISHI
MOTORS Authorized Service Point for a re-
placement remote control switch. Locking and unlocking
1-04
1

OBKE12E1

l
If you
wish to add a remote control switch,
we recommend you to contact a
MITSUBISHI MOTORS Authorized Service
Point.
A maximum of 4 remote control switches are
available for your vehicle.
Procedure for replacing the remote
control switch battery E00309500132
1. Before replacing the battery, remove static
electricity from

your body by touching a met-
al part such as doorknob of the room.
2. Remove the screw (A) from the remote con- trol switch. 3. With the MITSUBISHI mark facing you, in-
sert the

clothcovered tip of a straight blade
(or minus) screwdriver into the notch in the remote control switch case and use it to open
the case.
NOTE
l Be
sure to

perform the procedure with the
MITSUBISHI mark facing you. If the
MITSUBISHI mark is not facing you when
you open the remote control switch case, the
switches may come out. 4. Remove
the remote control transmitter from
the remote

control switch case. Then, open
the remote control transmitter using the meth-
od described in step 3. 5. Remove the old battery.
6. Install a
new

battery with the + side (B) down.
Coin type battery
CR1616
- side
+ side 7. Close the remote control transmitter firmly.
8. Place the remote control transmitter in the re-
mote control

switch case, then securely close
the remote control switch case.
9. Attach the screw (A) removed in step 2. Locking and unlocking
1-05 1

OBKE12E1

10. Check the keyless entry system to see that it
works.
NOTE l You may
purchase a replacement battery at
an electric appliance store.
l A MITSUBISHI MOTORS Authorized Serv-
ice Point can replace the battery for you if
you prefer. CAUTION
l
When the
remote
control switch case is
opened, be careful to keep water, dust,
etc. out. Also, do not touch the internal
components. Doors
E00300401177 CAUTION
l
Make sure
the
doors are closed: driving
with doors not completely closed is dan-
gerous.
l Never leave children in the vehicle unat-
tended.
l Be careful not to lock the doors while the
key is inside the vehicle.
To lock or unlock with the key 1- Lock
2- UnlockTo
lock
or unlock from inside the vehi-
cle 1- Lock
2- Unlock
Pull the

inside door handle towards you to open
the door.
To lock without using the key
Front door Locking and unlocking
1-06
1

OBKE12E1

Set the inside lock knob (1) to the locked position,
and while pulling
the outside handle up (2), close
the door (3).
Rear door (5-door models) Set the inside lock knob (1) to the locked position,
and close the door (2).
“Forgotten-key-prevention” mecha-
nism
E00300600273
If the key is in the ignition switch when you push
the lock knob

forward with the driver’s door open,
the lock knob will automatically return to the un-
locked position. Central door locks
E00300801692
NOTE l Each
of the

doors can be locked or unlocked
independently by using the inside lock knob.
l Repeated continuous operation between lock
and unlock could activate the central door
locking systems built-in protection circuit
and prevent the system from operating.
If this occurs, wait approximately 1 minute
before operating the central door lock switch
or the key.
Driver’s door with key (except for ve-
hicles with keyless entry system)
Using the key on the driver’s door locks or unlocks
all doors (including the backdoor). 1- Lock
2- UnlockDriver’s door with central door lock
switch
Using the
central
door lock switch locks or unlocks
all doors (including the backdoor). 1- Lock
2- Unlock Locking and unlocking
1-07 1

OBKE12E1

“Child-protection” rear doors (5-
door models) E003009008691- Lock
2- Unlock
Child protection
helps prevent the rear doors from
being opened accidentally from the inside.
If the lever is set to the locked position, the rear
door cannot be opened using the inside handle, but
only with the outside handle.
If the lever is set to the “Unlock” position, the
child protection mechanism does not function. CAUTION
l
When driving with
a child in the rear
seat, please use the child protection to pre-
vent accidental door opening which may
cause an accident. Approach lamps*
E00306100195
The lamps (A)

in the bottom of each mirror come
on to illuminate road surface while people are enter-
ing or exiting the vehicle. These lamps turn on/off as follows:
l The lamps come

on for approximately 15 sec-
onds when all of the doors (including the back-
door) are unlocked using the central door
lock function or the keyless entry system (if
so equipped).
l When any door or the backdoor is opened,
the lamp comes on for approximately 2 mi-
nutes.
If all of the doors (including the backdoor)
are closed while the lamps are on, the lamps
go off 30 seconds later. NOTE
l The
lamps go

off immediately if any of the
following actions is taken while the lamps
are on. • The ignition switch is turned to the “ON”position.
• All of the doors (including the backdoor) are locked using the central door lock func-
tion.
• All of the doors (including the backdoor) are locked using the keyless entry system
(if so equipped). Locking and unlocking
1-08
1

OBKE12E1

Backdoor
E00301300424WARNING
l It is
dangerous to drive with the back-
door open since carbon monoxide (CO)
gas can enter the cabin. You cannot see
or smell CO. It can cause unconscious-
ness and even death. CAUTION
l
When the
backdoor
is open, the rear-
right combination lamp is obscured by
the spare wheel.
If the backdoor is opened while the vehi-
cle is parked on the road, alert other road
users to the vehicle’s presence using a
warning triangle or other device as re-
quired by local legislation.
l When closing the backdoor, always en-
sure your or other person’s fingers can-
not be caught by the backdoor.
NOTE l The
backdoor is

equipped with an oil damper
type backdoor stopper, enabling you to hold
the backdoor at a desired position.
l While opening or closing the backdoor, you
may feel slight resistance. This is a structural
feature of the backdoor stopper that supports
the backdoor and does not indicate any abnor-
mality. To lock or unlock from outside the ve-
hicle (Except for vehicles with keyless
entry system)
1- Lock
2- Unlock
To lock

or unlock from inside the vehi-
cle
The backdoor can be locked or unlocked by using
the central door lock switch. 1- Lock
2- UnlockVehicles
without
keyless entry system, if the back-
door is locked

or unlocked by using the central
door lock switch, it can still be locked or unlocked
with the key.
NOTE
l Repeated continuous operating between lock
and unlock could cause the central door
lock’s built-in protection circuit to prevent
the system from operating. If this occurs,
wait approximately 1 minute before operat-
ing the central door lock switch.
l When the luggage compartment lamp is set
to the [•] position, the luggage compartment
lamp illuminates when the backdoor is
opened and turns off when it is closed.
To open
Pull the outside handle towards you to open the
backdoor. Locking and unlocking
1-09 1

OBKE12E1

Backdoor stopper
Open the
backdoor
fully and then move the locking
tube (A) to the LOCK position (B); this will ensure
that the backdoor remains in the fully opened posi-
tion. To subsequently release the stopper, move the
locking tube back to the UNLOCK position (C). CAUTION
l
When closing the
backdoor, be careful
not to trap your hands.
l Before closing the backdoor, make sure
that the locking tube (A) is in the UN-
LOCK position (C). Closing the back-
door with the locking tube (A) in the
LOCK position (B) may damage the back-
door stopper, rendering the backdoor un-
able to be closed. Security alarm system*
E00301500657
The security alarm

system is designed to prevent un-
lawful entry into the vehicle. It will alert people
nearby if a door, the backdoor, or the bonnet is
opened when the vehicle has not been unlocked us-
ing the keyless entry system.
Also, the alarm will be activated if any of the fol-
lowing occur.
l Attempt an unlawful moving of the vehicle.
(the vehicle inclination detection function)
l Detect a motion in the vehicle. (the interior
intrusion detection function)
l Disconnect the battery terminal.
The security alarm system is set to “active” when
the vehicle leaves the factory.
When making changes to the settings, please fol-
low the procedure listed in the section titled “Chang-
ing the system settings” on page 1-11. CAUTION
l
Do not
modify
or add parts to the securi-
ty alarm system.
Doing so could cause the security alarm
to malfunction.
NOTE l The
alarm system

will not be activated if the
doors (including the backdoor) have been
locked using a key or the central door lock
switch (instead of the keyless entry system). l
If the
turn-signal
lamps do not blink after the
locking and unlocking operation using the
keyless entry system, the security alarm sys-
tem may be malfunctioning.
Have the vehicle inspected at a
MITSUBISHI MOTORS Authorized Service
Point.
l In the following situations, the security
alarm system could be more likely to be acci-
dentally activated.
• Using a car wash
• Taking the vehicle on a ferry
• Parking in an automated car park
• Leaving someone or a pet in the vehicle
• Leaving a window, door, or the sunroofopen
• Leaving an unstable object such as a stuf- fed toy or accessory in the vehicle
• Suffering a continuous impact or vibra- tion by hail, thunder, etc.
l The sensitivity of the vehicle inclination de-
tection function and the interior intrusion de-
tection function can be adjusted. For details,
please contact a MITSUBISHI MOTORS Au-
thorized Service Point. Locking and unlocking
1-10
1

OBKE12E1

The security alarm has four modes:
System preparation mode (approx. 20 seconds)
(The buzzer
sounds
intermittently, and the security
alarm indicator (A) blinks) The system preparation time extends from the
point at
which

all of the doors (including the back-
door) are locked by the keyless entry switch to the
point at which the system activation mode goes in-
to effect.
During this time, it is possible to temporarily open
a door without using the keyless entry system and
without causing the alarm to sound (for example,
when you forget something inside the vehicle or re-
alize that a window is open).
System armed mode
(The buzzer stops, and the security alarm indicator
continues to blink slowly)
Once the system preparation mode has ended, the
system armed mode starts. If an unlawful opening
of any of the doors (including the backdoor) or the
bonnet is detected during the system armed mode,
the alarm will be activated to warn people around
the vehicle of an abnormal condition. Also, if unlawful moving of the vehicle is attemp-
ted or
a

vehicle intrusion is detected, the alarm will
be activated.
Alarm activation
The turn-signal lamps blink and the siren sounds
for approximately 30 seconds. Refer to “Alarm ac-
tivation” on page 1-14.
NOTE
l The alarm will resume if unlawful actions
are taken again, even if the alarm has stopped.
System cancellation
It is possible to cancel the system activation during
the system preparation mode or the system armed
mode.
In addition, it is possible to cancel the alarm once it
has been activated.
Refer to “Cancelling the system” on page 1-13,
“Cancelling the alarm” on page 1-14.
NOTE l When lending the vehicle to another person
or allowing the vehicle to be driven by some-
one who is unfamiliar with the security
alarm system, be sure to give the person a
proper explanation of the security alarm sys-
tem or set the security alarm system to the “in-
active” mode.
If a person who is unfamiliar with the securi-
ty alarm system accidentally unlocked the ve-
hicle, causing the alarm to sound, the alarm
would be a nuisance to people nearby. Changing the security alarm settings
E00301600212
It is possible
to set the security alarm to the “ac-
tive” mode or “inactive” mode.
Follow the procedure below. 1. Remove the key from the ignition switch.
2. Place the lamp switch in the “OFF” position,and leave the driver’s door open. 3. Pull
the windscreen wiper and washer switch
towards you and hold it there. Locking and unlocking
1-11 1

OBKE12E1