check engine MITSUBISHI SPYDER 1990 Service Repair Manual

ENGINE (TURBO)
AND Troubleshooting
INSPECTION PROCEDURE 9
speed is high. (Improper idle speed)
[Comment]
In such cases as the above, the cause is probably that the intake air volume during idle is too
great.
YES
Refer to INSPECTION CHART FOR Are diagnostic troublecodesoutputTROUBLE CODES.
Check the idle air control motor for operation sound Engine (Turbo)>. (Refer to Check the idle air control motor for operation sound Engine>. (Refer to
OKCheck the idle control system malfunction (Refer
INSPECTION PROCEDURE FOR DIAGNOSTIC TROUBLE CODE
NGSCAN TOOL Data list Check the closed throttle position 26 Closed throttle position switch (Refer to (Refer to INSPECTION PROCEDURE FOR TROUBLE CODE
SCAN TOOL Data listNG Check the engine coolant’ temperature 21 I N S P E C T I O N
P R O C E D U RE
OKTROUBLE CODES
SCAN TOOL Data list
28 A/C switch (Refer to
OK
Adjust the basic idle speed. (Refer to
Check the A/C switch and clutch to INSPECTION PROCEDURE 32.)
Check trouble symptom.
N G
Clean the throttle valve area. (Refer to
Check and the fixed SAS. (Refer to .
TSB RevisionI

ENGINE (TURBO)
AND
ENGINE> Troubleshooting
INSPECTION PROCEDURE 10
Idle speed is low. (Improper idle speed)“ P r o b a b l e c a u s e , .
[Commentjl Malfunction of the systemIn cases such as the the cause is probably that the intake air volume d uring idling is l of throttle small.
SCAN TOOL DTCYES
Are diagnostic trouble codesoutputRefer to I N S P E C T I O N C H A R T TROUBLE CODES.
NO
Check the idle air control motor for operation soun d Engine (Refer to Check the idle air control motor for operation sound (Refer to
OK
SCAN TOOL Data listNG
26 Closed positionswitch(Refer to
Check the idle control system to INSPECTION PROCEDURE FOR DIAGNOSTIC
,
Check the closed position switch system.(Refer to PROCEDURE FOR T R O U B L E C O D E
SCAN TOOL Data list21 Check the engine coolant temperature circuit malfu nction. (Refer I N S P E C T I O N P R O C E D U R E TROUBLE CODES 15.)
SCAN TOOL Data listNG
29 Park/neutral position switch (Refer toCheck the ignition switch-ST and park/neutral posit ion system.(Refer to INSPECTION PROCEDURE ,
OK
Adjust the basic idle (Refer to
Clean the throttle valve area. to
I
TSB Revision
Check and adjust the fixed SAS. (Refer to
.

ENGINE (TURBO)
AND ENGINE> Troubleshooting
INSPECTION PROCEDURE 11
When the engine is cold, it stalls at idle. (Die out)P r o b a b l e c a u s e .
[Comment]l Malfunction of the system
In such cases as the above, the cause is probably t hat the mixture is inappropriate whenl the bodythe engine is cold, or that the intake air volume is insufficient.l Malfunction of the injector system Malfunction of the s y s t e m
W ere the battery terminals disconnected recently
NO
After warming-up, let the engine run at idling for 10 minutes.
SCAN TOOL DTC
Are diagnostic trouble codesoutput?Refer to INSPECTION CHART FOR TROUBLE CODES.
(Refer to Check and adjust the (Refer to ,
NO
Is engine-idling stable after the warming-up
YES(Refer to INSPECTION PROCEDURE
Check the idle air control motor for operation soun d NG
Engine (Turbo)>. (Refer to Check the idle air control motor for operation sound (Refer to
Checktheinjectorforope
OK
Check the idle control system malfunction to .INSPECTION PROCEDURE FOR DIAGNOSTIC TROUBLE CODE
PROCEDURE FOR DIAGNOSTIC TROUBLE CODES
SCAN TOOL Data list Check the closed position switch system.
26 Closed throttle position switch (Refer to INSPECTION PROCEDURE FOR
OKTROUBLE CODES
SCAN TOOL Data listN G Check the engine coolant temperature circuit malfu nction. (Refer to21 Enginecoolanttemperaturesensor P. I N S P E C T I O N P R O C E D U R E F O R TROUBLE CODES
Check the fuel pressure. (Refer to I
Check the ignition timing. Engine Check that the position sensor and belt cover are
(Refer to GROUP
(Refer to GROUP Check the ignition timing. Engine>
Check the following items.
l Check the ignition coil, spark plugs, spark plug ca bles.
l Check the compression pressure.
l Check the engine oil viscosity.
TSB Revision

ENGINE (TURBO)
AND ENGINE> Troubleshooting
INSPECTION PROCEDURE 12.
When the engine is hot, it stalls at idle. (Die out)Probable cause
l Malfunction of the ignition system In cases such as the above, the cause is probably t hat ignition system, air/fuel mixture, idle airl Malfunction control systemcontrol motor or compression pressure is defective.l M a l f u n c t i o n o f system In addition, if the engine suddenly stalls, the cau se may also be a defective connector contact.l Drawing air into intake system
l I m p r o p e r c o n n e c t o r c o n t a c t
W ere the battery terminals disconnected recently After warming-up, let the engine run at idling for minutes.
NO
SCAN TOOL DTC
Are diagnostic trouble codes output?YESRefer to I N S P E C T I O N C H A R T TROUBLE CODES.
Check the idle air controlEngine (Refer Check the idle control system malfunction (Refer to
INSPECTION PROCEDURE FOR DIAGNOSTIC TROUBLE CODE
Check the idle air control motor for operation soun d
(Refer to
Checktheinjectorforoperati
OKPROCEDURE FOR DIAGNOSTIC ,
I
Does the engine stall N O While carrying out an intermittent malfunction sim
ulation test (Refer
YESto GROUP 00 How to Cope with Intermittent Malfunctions, check
for sudden changes in the signals shown below.
Scan tool: Inspection when engine stalls when the e nginel Crankshaft position sensor Primary is warm and idling INSPECTION signal signal
CEDURE 41.) Volumeairflowsensorsignal l
Fuel pump drive signal
OK l
Injector drive signal l ECM power supply voltage
TSB Revision
Check the ignition timing. Engine (Turbo)>
(Refer to GROUP On-vehicle Service.)
Check the ignition timing. Engine>
(Refer to GROUP On-vehicle Service.)
Check that the crankshaft position sensor and timin g belt cover are
installed properly.
Check the following items.
l Check the ignition coil, spark plugs, spark plug ca bles.
l Check if the injectors are clogged.
l Check the compression pressure.
l Check if foreign materials (water, alcohol, etc.) g ot into fuel.

ENGINE (TURBO)
AND ENGINE> Troubleshooting
INSPECTION PROCEDURE 13,
The engine stalls when accelerating. (Pass out)Probable
[Comment]l
Drawing air into intake system
In cases such as the above, the cause is probably m isfiring due to a weak spark, or an M a l f u n c t i o n o f system
air/fuel mixture when the accelerator pedal is depressed.
SCAN TOOL DTCYES
Are diagnostic trouble codes output
N O
Check the following items. l Check the ignition coil, spark plugs, spark plug ca bles.
l Check if air was drawn into the intake system.
Broken intake manifold gasket
Broken or disconnected vacuum hose Refer to
INSPECTION CHART FOR DIAGNOSTICTROUBLE CODES.
.
Improper operation of the PCV valve
Broken air intake hose
INSPECTION PROCEDURE 14
The engine stalls when decelerating. Probable
[Comment]l
Malfunction of the system.In cases such as the above, the cause is probably t hat the intake air volume is insufficient dueto a defective idle air control motor system.
W ere the battery terminals disconnected recently
NOAfter warming-up, let the engine
at-idling for 10
SCAN TOOL DTC
Are diagnostic trouble codes output? Refer to INSPECTION CHART FOR DIAGNOSTICTROUBLE CODES.
SCAN TOOL Data list
26 Closed throttle position switch (Refer to Check the closed throttle position switch system.(Refer to INSPECTION PROCEDURE FOR TROUBLE CODE
SCAN TOOL Data list 14 Throttle position sensor (Refer to Check the malfunction (Refer to IN- PROCEDURE FOR DIAGNOSTIC TROUBLE CODE
SCAN TOOL Data list YES
45 Idle air control motor position
Engine (Turbo)>
55 Idle air control valve position sensor Engine>lIs the idle speed control motor position drops to steps when decelerating (engine rpm less than 1
Check the vehicle speed sensor malfunction (Refer to PROCEDURE FOR DIAGNOSTIC TROUBLE CODE
N O
Check the following items.’
l Check the ignition coil, spark plugs, spark plug ca bles.
l Clean the throttle valve area.
l Check and adjust the fixed SAS.
Revision

ENGINE (TURBO)
AND ENGINE> T r o u b l e s h o o t i n g
INSPECTION PROCEDURE 15
Hesitation, sag or stumbleProbable
[Comment]Malfunction of the ignition system
In cases such as the above, the cause is probably t hat ignition system, air/fuel or l of pressure is defective. of the fuel l Malfunction of the system Poor compression Malfunction of the turbocharger,
Arediagnostic trouble codesoutput
Check the injectors for operationsound.(Refer to
OK
Refer to INSPECTION FOR DIAGNOSTICTROUBLE CODES.. .
Check the injector circuit malfunction PROCEDURE FOR DIAGNOSTIC
Check the ignition timing. Engine (Turbo)>
(Refer to GROUP On-vehicle Service.)
Check the ignition timing.
(Refer to GROUP 11 On-vehicle Service.)
Check that the crankshaft position and cover installed properly.
OK
Scan Tool: Inspection when hesitation, sag, stumble or pooracceleration occurs. (Refer to INSPECTION
PROCEDURE 42.)
IOK
Check the fuel pressure. (Refer to
O K
Check the following items.
l Check the ignition coil, spark plugs, spark plug ca bles.
l Check supercharging pressure.
l Check intake charge pressure control system.
l Check rotating resistance of turbocharger turbine w heel. (Does the wheel rotate smoothly?)
Check the EGR system.l Check the compression pressure.lCheck the fuel filter or fuel line for clogging.
INSPECTION PROCEDURE 16
Acceleration shock
[Comment]
In cases such as the above, the cause is probably t hat there is an ignition leak accompanying
the increase in the spark plug demand voltage durin g acceleration.
Probable cause
M a l f u n c t i o n system
SCAN TOOL DTC
Are diagnostic trouble codes output
NORefer to
INSPECTION CHART FOR DIAGNOSTIC
T R O U B L E C O D E S .
,
Check the following items.
l Check the ignition coil, spark plugs, spark plug ca bles.
l Check for occurrence of ignition leak.
TSB Revision

ENGINE (TURBO)
AND
ENGINE> Troubleshooting
INSPECTION PROCEDURE 17
Probable causeI
[Comment]l Malfunction of the system
Malfunction of the system is suspected.
Are diagnostic trouble codes output
YESRefer to INSPECTION FOR DIAGNOSTICTROUBLE CODES.
Check theidle air control motor for operation sound Engine (Refer to Check the idle air control motor for operation soun d Engine>. (Refer to
SCAN TOOL Data list
14 Throttle position sensor (Refer to
OK
Check the idle control system malfunction (Refer t o INSPECTION PROCEDURE FOR DIAGNOSTIC TROUBLE CODE
Check the throttle position circuit malfunction (Refer to PROCEDURE FOR DIAGNOSTIC TROUBLE 20.)
NG,
SCAN TOOL Data list Check closed position switch system.
26 Closed throttle position switch (Refer to (Refer to INSPECTION PROCEDURE FOR DIAGNOSTICTROUBLE CODE .
. .
Clean the throttle valve area. (Refer to
INSPECTION PROCEDURE 18
Poor acceleration Probable cause I
[Comment]
Defective ignition system, abnormal air-fuel ratio, poor compression pressure, etc. are l Malfunction of the Ignition system Malfunction of air-fuel ratio control l Malfunction of the fuel supply system Poor acceleration
l C l o g g e d e x h a u s t s y s t e m
l Malfunction ‘of turbocharger system .
SCAN TOOL DTC
Are diagnostic trouble codes output
YESRefer to INSPECTION CHART FOR DIAGNOSTICTROUBLE CODES.
Check the injectors for opNG
(Refer to PROCEDURE FOR DIAGNOSTIC TROUBLE
OK
Check the ignition timing. Engine (Turbo)>
(Refer to GROUP A On-vehicle Service.)
Check the ignition timing. Engine>
Check that the crankshaft position sensor and timi ng belt cover are
installed
(Refer to GROUP On-vehicle Service.)
OK
Scan tool: Inspection when hesitation. stumble or poor acceleration occur. (Refer to INSPECTIONPROCEDURE 42.)I
OK
Check the fuel pressure. (Refer to
OK
Check the following items.
l Check the ignition coil, spark plugs, spark plug ca bles.
l Check supercharging pressure.
l Check intake charge pressure control system.
l Check rotating resistance of turbocharger turbine w heel. (Does the wheel rotate smoothly?)
l Check the compression pressure.
lCheck the fuel filter or fuel for clogging.
l Broken air intake hose
Clogged air cleaner
l Clogged exhaust system
Revision

ENGINE (TURBO)
AND ENGINE> Troubleshootina
INSPECTION PROCEDURE 19
Surge
Defective ignition system, abnormal air-fuel are suspected.
, .
l Malfunction of ignition systeml Malfunction of’ ‘ratio ‘control system l Malfunction of the EGR solenoid system
Are diagnostic trouble codes output
YES ,
Refer to INSPECTION CHART FOR DIAGNOSTICTROUBLE CODES.
.
Check the injectors for opNG
(Refer to PROCEDURE FOR TROUBLE
OK
Check the ignition timing. Engine (Turbo)> Check that the crankshaft position sensor and are properly.(Refer to GROUP On-vehicle Service.)
Check the Engine>
(Refer to GROUP On-vehicle Service.)
Scan Tool: Inspection when surge occurs. (Refer to INSPECTION PROCEDURE 43.)
OK
Check the fuel pressure. (Refer to
OK
Check the following items.
l Check the ignition coil, spark plugs, spark plug ca bles.
l Check the EGR system.
l Check the
waste actuator.
INSPECTION PROCEDURE 20
Knocking Probable cause
[Comment]l Defective knock sensor ,
In cases such as the above, the cause is probably t hat the detonation control is defective or thel heat the
heat value of the spark plug is inappropriate.. .
YESRefer to INSPECTION CHART FOR’ ‘DIAGNOSTIC Are diagnostic trouble codes output TROUBLE CODES.
NO
NODoes knocking occur when driving with the sensor Check the knock sensor 1 circuit malfunction (Refe r INSPECTION PROCEDURE FOR CODE’At this time, use the scan tool to check if the timing isretarded compared to when the knock sensor connecto ris connected.
YES
Check the following items.
l Spark plugs heat range
l Check if foreign materials (water, alcohol, etc.) g ot into fuel.
INSPECTION PROCEDURE 21
DieselingProbableI
[Comment]
Fuel leakage from injectors is suspected.l Fuel leakage from injectors
Check the injectors for fuel leakage.
TSB Revision

ENGINE (TURBO)
AND ENGINE> Troubleshooting
INSPECTION PROCEDURE 22
Too high CO and HC concentration when idling
[Comment]Malfunction of the ratio
Abnormal air-fuel ratio is suspected.
SCAN TOOL Are diagnostic trouble codes output
N O
YES Refer to INSPECTION CHART FOR DIAGNOSTICTROUBLE CODES.
Check the ignition timing. Engine (Turbo)>NG
(Refer to GROUP On-vehicle Service.) Check that the crankshaft position sensor and belt installedCheck the ignition timing. Engine>(Refer to GROUP 11 On-vehicle Service.)
OK
NGSCAN TOOL Data list
21 Engine coolant temperature sensor. Check the engine coolant temperature malfunction. (Refer to
(Refer to INSPECTION PROCEDURE FOR DIAGNOSTIC
TROUBLE CODES
OK
SCAN TOOL Data listNG Check the intake air temperature (Refer to
13 Intake air temperature sensor (Refer to INSPECTION PROCEDURE FOR DIAGNOSTIC
OK TROUBLE CODE
SCAN TOOL Data list
25 Barometric pressure sensor (Refer to
OK
Check the pressure circuit malfunction. INSPECTION PROCEDURE FOR DIAGNOSTIC TROUBLE CODE
SCAN TOOL Data listNGCheck the oxygen sensor circuit malfunction (bank sensor 2). (Refer59 Heated oxygen sensor (rear) (Refer to to INSPECTION PROCEDURE FOR DIAGNOSTIC
l Transaxle gear TROUBLE CODE ranae l Driving with the throttle wide open
O K :
OK
SCAN TOOL Data list NG
Heated oxygen sensor (front) (Refer to OK: 1,000 when racing suddenly
OK
SCAN TOOL Data list11 Heated oxygen sensor (front) (Refer to O K : and
Check the oxygen sensor circuit malfunction (bank 1 sensor 1). INSPECTION PROCEDURE FOR DIAGNOSTICTROUBLE CODE
alternately when idling.
NG
Check the fuel pressure. (Refer to
Check the following items.
l Check the injectors for operation sound.
l Check the injectors for fuel leakage.
l Check the ignition coil, spark plugs, spark plug ca bles.
l Check the compression pressure.
l Check the positive crankcase ventilation system.
l Check the evaporative emission control system.
l Check the
system.I
Check trouble symptom.
Replace the three-way converter.
TSB Revision

ENGINE (‘TURBO)
AND ENGINE>
INSPECTION PROCEDURE 23
,
Generator output voltage is low (approx.
[Comment]
The cause may be a malfunction of the generator or one of the problems listed at right.l M a l f u n c t i o n o f c h a r g i n g s y s t e m . l Short harness between t e r m i n a l l Malfunction of the ECM.
OK Check the generator.
,
,. . ,
1
Measure at the generator connector l Connect the connector.
l Voltage between and ground
Engine: idle
Radiator fan: stopped
Headlight: off
on
Stop lamp: off on
Check the following
Check the harness wire between generator and ECM co nnector.
Repair, if necessary.
TSB Revision