diagram NISSAN 300ZX 1984 Z31 Body Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1984, Model line: 300ZX, Model: NISSAN 300ZX 1984 Z31Pages: 77, PDF Size: 1.97 MB
Page 11 of 77
BODYENDANDDOOR
Front Door (Cont'd)
POWER WINDOWIWI RING DrAGRAM
(White)
HARNESS POWER WINOOW SUB SWITCH IAssistI --Ass161 MAIN HARNESS LIY-
BATTERY (Via fusible link1
POWER WINDOW
MOTOR IAssirtl
LIY
POWER WINDOW
MOTOR IDriverI
(Driver) LN -
IGNITION SWITCH
ON or START
IGNITION RELAY
w CIRCUIT BREAKER
lured together with power seat1
To engine room harness (Ground)
HARNESS DOOR HARNESS
SBF408B
power door lock actuator POWER DOOR LOCK/WIRING DIAGRAM
FUSE BLOCK
u
I
I L
To engme room - harness IGroundl
.
Power door lock switch
MAIN DOOR HARNESS HARNESS -Driver
SBF409B
BF-I 1
Page 22 of 77
BODY END AND DOOR
Theft Warning System (Cont'd)
WIRING DIAGRAM
BF-22
Page 24 of 77
BODYENDANDDOOR
Theft Warning System (Cont'd)
TROUBLE-SHOOTING
0 When disconnecting the main harness connector, as instructed in this trouble-shooting, always be sure to
remove the battery ground cable
first
In trouble-shooting, if the cause of trouble is found to be due to the "Faulty sub-control AMP" or
"Faulty main control AMP", be sure to refer to "Controller inspection"
0 @ through @ indicate the respective terminals of the main harness connector (refer to Wiring
Diagram)
The term "door" indicates the driver door, assist side door, back door, and hood, unless otherwise
specif led.
The term "alarm" means
that the horn sounds intermittently and the headlamps blink 0
0 Contents
-
Will not blmk (Remains out1 -Disarmed phase
Remains blinking - Disarmed phase
Will not mme on
Will not come on
- Ready phase with key lock
- Ready phase with keyless lock and closing hood lor back door1 after
closing & locking doors
Remains lighted -Disarmed phaseand resetting
from ready phase
Will not go out (Comer on1 - Disarmed phase
Will not go out (Remains lighted1 -Armed phase
. ISset -Disarmed phase
~snot ret - Ready & armed phase
isgiven Without any cause - Armed phase
Will not operate -Alarm phase
Will not stop (Alarm continuer
over 4 minutes) -Alarm phase
stops
too soon IWIII not contlrlue
2 to 4 minutes) -Alarm phase
Continues 1,s not intermittent) -Alarm phase
0 Cannot operate
Canoperate -Alarm phase
Cannot be performed
.
- Except alarm phase
indicator lamp
Reset by unlocking power door lock
Reset by opening door
cylinder with key
4iarm
;tarter motor
3eret
IND-@
INO-@
IND-@
INO-@
IND-@
INO-@
INO-a
ARM-@
ARM-@
ALR-@
ALR-@
ALR-@
ALR.@
ALR-@
ST. @
ST- @
RES
Symbol. Condition 11 Action 0 Judgment Probable cause
BF-24
Page 51 of 77
SEAT
Front Driver Seat (Cont'd)
Air diagram
AN make
tl if hose mnnemon IS disconnected, apply sealant to hoseconnection to prevent air leakage [@ portion onlv) Install each valve ~n Its proper PoSltlOn
[Yellow marking)
Onewav valve
@ sealant portion
SBF392B
BF-51
Page 54 of 77
SEAT
Front Driver Seat (Cont'd)
Air diagram
Lumbar support
Thigh support switch
e
If hose connection 1s disconnected, apply sealant to hose
connection to prevent air leakage I@ portion only) Be sure air pump 1s free from dust. foreign substance, etc
Install safety valve in Its proper direction
Air pump operates only when each swjtch IS turned ON
@ Sealant portion
SBF394B
BF-54
Page 57 of 77
SEAT BELT
Refer to MA section for installation of seat belts.
GLL model has been equipped with seat belts with tension reducer This unit reduces the force required
to pull out seat belt while in use, and lessens pressure on the shoulder and hips for greater comfort
TENSION REDUCER WIRING DIAGRAM
IGNITION SWITCH I ON or ST
TENSION REDUCER-Assist
FUSE BLOCK
@
U
SEAT BELT SWITCH-Assist Iinrjde retractor1 (Main harness1
TENSION REDUCER-Driver (Inside retractor)
SEAT BELT SWITCH-Drwer IM~I~ IPower
harness1 To rime control unit (Seat belt warning lamp1
To engine room harness (Ground)
__ seat cushion ground
TENSION REDUCE OPERATION
SBF439B
Fully Seat belt stroke Fully retraned pulled out SBFMOE
Page 69 of 77
MIRROR
Door Mirror
1 Initial setting
23 3 (0 23. ONm ,O 31 kgm. 1 7.2 2 ft-lb)
of temporarily-lnrralled link (D Hook the bar With the hook and make sure It ts hooked
@ Tilt mirror body backward and while holding mirror. remove temporarily-Installed link
Never remove temporarily-installed link from mirror
body, before hooking the bar
with the hook
SBF4348 L
ELECTRICAL REMOTE CONTROL DOOR MlRRORNVlRlNG DIAGRAM
IWhntd
ImI mI nnAm
“1L-a
DOOR MIRROR
DEFOGGER
BF-69