Starter NISSAN 300ZX 1984 Z31 Electrical System Workshop Manual

ELECTRICAL SYSTEM
I
SECTION EL
CONTENTS
HOW TO READ DIAGRAMS
STANDARDIZED RELAY
POWER SUPPLY ROUTING
BATTERY.
.. ..
STARTING SYSTEM .
STARTING SYSTEM -Starter -
CHARGING SYSTEM .
CHARGING SYSTEM - Alternator
COMB IN AT1 ON SWITCH
INSTRUMENT SWITCH
HEADLAMP
EXTERIOR LAMP,
INTERIOR LAMP
.
..
..
..
..
..
... ......
..
.. ....
..
.. ...
EL- 2
EL- 3
EL- 4
EL- 6
EL- 9
EL-
10
EL- 15
EL- 17
EL- 23
EL- 25
EL- 26
EL- 34
EL- 38
METER AND GAUGES - Digital Type Combination Meter . . EL- 41
METER AND GAUGES - Digital Type Combination Gauge . .. .. EL- 57
METER AND GAUGES - Needle Type Combination Meter .. . EL- 65
METER AND GAUGES
- Needle Type Combination Gauge.. .... EL- 68
WARNING LAMPS AND CHIME. .......... ... .... EL- 71
VOICE WARNING SYSTEM
... ... EL- 76
TIME CONTROL SYSTEM ... EL- 81
WIPER AND WASHER .... .... ... ... . EL- 89
HORN, CIGARETTE LIGHTER, CLOCK . . ......... EL- 92
REAR WINDOW DEFOGGER
... .. ... ....... EL- 93
AUDIO AND POWER ANTENNA
,. . .... .. . EL- 95
AUTOMATIC SPEED CONTROL DEVICE (AS
C D ) . ... , . EL- 97
LOCATION OF ELECTRICAL UNITS
... .. .. .. EL-104
HARNESS LAYOUT
. . .. .. .. . EL-107

STARTING SYSTEM
Wiring Diagram
MIT MODELS FUSIBLE LINK BOX
THEFT WARNING
RELAY 2
IGNITION
SWITCH
-1
- STARTER MOTOR
AIT MODELS
lNHlBlTOR SWITCH
BATTERY
THEFT
WARNING
RELAY9 INHIBITOR
RELAY .W
FUSIBLE LINK BOX
EL-9

STARTING SYSTEM -Starter-
Construction
S114-3748
SEL623D
EL-I 0

~~ STARTING SYSTEM -Starter-
Magnetic Switch
Check
1 Continuity test (between "S" terminal and
switch body)
No continuity Replace
From battery
VL Ohmrnet
2 Continuity test (between "S" terminal and
"M" terminal)
No continuity Replace
Coli
SEL047D
- Pinion/Clutch Check
1 Check clutch
Check pinion to see that it locks properly
when turned in "drive" direction and rotates
smoothly when turned in reverse
SEL569B
Pinion does not lock in either direction or
unusual resistance
is evident Replace
Replace pinion if teeth are worn or dam-
aged (Also check condition
of ring gear
teeth )
Replace clutch gear if teeth are worn or
damaged (Also check condition
of arma-
ture shaft gear teeth
)
2 Inspect pinion teeth.
3 Inspect clutch gear teeth
EL-I 1

STARTING SYSTEM -Starter-
Brush Check
BRUSH
Check wear of brush
Wear limit length: 11 mm (0.43 in)
Vernier caliper
SEL626B
Excessive wear Replace
BRUSH HOLDER
1 Perform insulation test between brush holder
(positive side) and its base (negative side)
SE L568B
Continuity exists . Replace
smoothly
2 Check brush holder to see if it moves
If brush holder is bent, replace it, if sliding
surface
is dirty, clean
Field Coil Check
Continuity test (between field coil positive
terminal and positive brushes)
ositive terminal
‘Ohmmeter
No continuity Replace fielk ~
SELUq6A
:oil
Insulation test (between field coil positive
terminal
and yoke)
Postwe terminal
I
1%
Continuity exists Replace field coil
EL-I 2

STARTING SYSTEM -Starter-
1 Continuity test (between two segments side by
side)
IY Ohrnketer
a No continuity Replace
Insulation
test (between each commutator bar
and shaft) 2
EE022
a Continuity exists Replace
a Rough . Sand lightly with No 500 - 600
3 Check commutator surface
sandpaper
! Check
4 Check diameter of commutator
Commutator minimum diameter
Less than specified value Replace
29 mm (1 14 in)
vernier caliper
tJ \Cornmurator
SEL418A
5 Check depth of insulating mica from commuta-
tor surface
a Less than 0 2 mm (0 008 in) Undercut
to 0 5.0 8 mrn (0 020 - 0 031 in)
Undercut procedures
Round 0 5 -08 mm (0 020 0 031 in)
Correct
Commutator
incorrect EEOZI
EL-1 3

STARTING SYSTEM -Starter-
Minimum length of brush mm (In)
Reassembly
11 10431
Carefully observe the following instructions
a. Apply grease
to:
Rear cover metal
Gear case metal
Frictional surface of pinion
Plunger of magnetic switch
Moving portion of shift lever
With pinion driven out by magnetic switch, push
pinion back to remove slack and measure dif-
ference
"2" between the front edge of the pinion
and the pinion stopper.
Difference "P":
0.3 - 1.5 mm (0 012. 0.059 in)
"Q" 4+
SEL497D
Not in the specified value Adjust by dust
cover (Adjusting plate).
SEL5738
- Service Data and Specification-
- Applied model I A1 1
Less than 100 -
I Revolution rpm I Mare than 3.900
I More than 29 (1 141 Outer diameter of commutator mm (in1
157 196
1 116 20.35-44) Brush spring tension N (kg. Ibl
mm(in1 1 03-1510012-00591 Difference P" in height
of pinion assembly
EL-I 4