belt NISSAN GT-R 1998 User Guide

ENGINE MECHANICAL
TIGHTENING TORQUE
Engine cover
' Throttle body
Throttle position sensor
IAA unit (ACC valve)
' Intake manifold collector
(upper)
' Intake manifold collector
Intake manifold
Vacuum tank
Engine coolant temperature
sensor
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Exhaust manifold cover
Exhaust manifold
Oxygen sensor
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Ttming belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
Ignition coil
Spark plug
Rocker cover
* Camshaft bracket
Camshaft baffle plate Unit:
Nm (kg-m)
5.0
- 6.5 (0.51 - 0.66)
1) 8.8
- 11 (0.9 - 1.1)
2) 18
- 22 (1.8 - 2.2)
2.0
- 2.4 (0.20 - 0.24)
8.4
- 11 (0.86 - 1 .I)
18
- 22 (1.8 - 2.2)
5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5 - 7.5 (0.56 - 0.76)
2) 5.5 - 7.5 (0.56 - 0.76)
:Tighten separately in twice.)
Cylinder head bolt
Cylinder head sub bolt
VTC solenoid
Main bearing cap
Connecting rod nut
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump
(M6 bolt)
(M8 bolt)
(M 1 0 bolt)
Water inlet
Oil pump assembly
-
Accelerator cable lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube
Front tube to catalytic
converter
Catalytic converter to center
tube Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N.m (kg-m)
1) 29 (3.0)
2) 98 (10.0) 3) 0 (0)
@
4)
25 - 34 (2.5 - 3.5)
5) 95" - 100"
(Angle tightening)
E
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5) j$? 49 - 59 (5.0 - 6.0)
1) 14- 16
(1.4- 1.6)
2) 60"
- 65" BR
(Angle tightening)
93
- 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5)
25
- 34 (2.5 - 3.5) a=
': Tighten as specified tightening order.
1): Tighten separately in several times.

ENGINE MECHANICAL
STANDARD AND REPAIR LIMIT
Distortion limit mm
- - Intake manifold
Intake manifold collector
1 -5-3-6-2-4
1.20 (1
2.2)/300
0.90 (9.2)/300
0.1 (1.0)/300
Firing order
-- - 0.1
0.1
- -- - ( Cylinder block 0.1
Compression
pressure
MPa
(kg/cm2)/rpm
Exhaust manifold
Cvlinder head
Engine oil capacity Standard
Limit
-
Limit of variation between cylinders
0.3
0.2
- - -- - Spark plug I ~akerfl~~e/~~ark plug gap mm r NGKPFRGG-11/1.0 - 1.1
Without
filter
'with
filter
ignition advance device
I Electronically-controlled ignition advance
Approx.
3.9
Aoorox.
4.3
Engine idling speed
rPm
Idle
base speed (during no feed back control)
Pm
650-e50
(N or P position for
A/T)
600 (N or P position for AQ
Density of COIHC at idling speed
Wppm
Ignition timing (during no feed back control)
BTDCO/rpm Less
thanbl~ess than 50
15dY600
Valve clearance
(INT/EXH) mm
Deflection amount of accessory V-belt Hot
engine
Cold engine (at ambient temperature)
Measured
with tension gauge
(kg)
I
SEC.117 Power steering
Fan belt pump belt
0.36+0.062/0.53i0.062
0.3
1 20 .04/0.50a0.04
Fuel tank capacity
4
Engine coolant total capacity [with reservoir tank (max. level)] t
Thermostat opening temperature [start to open - full open]
OC
Radiator cap opening pressure
MPa (kg/cm2)
Power steering pump belt
Measured by pushing at 98
N (1 0 kg)
mm Approx.
65
Approx. 9.4
82
- 95
0.06
- 0.1 0 (0.6 - 1 .O)
New 1 Used 1 Limit
AfC
compressor belt
Fan belt
,
667 - 755
(68
- 77)
Power steering pump belt
' AfC compressor belt
Fan belt
559 - 637 284 (29)
(57 - 65)
667
- 755
(68
- 77)
667
- 755
(68
- 77)
559 - 637 284 (29)
(57 - 65)
559 - 637 284 (29) (57 - 65)
8-
10
6-8
3 - 5
- 10 - 12 16
7-9 12
4
- 6 7.5

ENGINE MECHANICAL pEZBq
TIGHTENING TORQUE
Engine cover
' Throttle body
Throttle position sensor
IAA unit
(ACC valve)
' Intake manifold collector
* Intake manifold
Engine coolant temperature
sensor
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Turbocharger Oil tube
Water tube (block side)
(turbocharger side)
Oxygen sensor
Exhaust manifold cover
' Exhaust manifold
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Timing belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
Ignition coil
Spark plug
' Rocker cover
' Camshaft bracket
Camshaft baffle plate Unit:
N.m (kg-m)
5.0
- 6.5 (0.51 - 0.66)
1)
8.8
- 11 (0.9 - 1.1)
2)
18
- 22 (1 -8 - 2.2)
2.0
- 2.4 (0.20 - 0.24)
8.4
- 11 (0.86 - 1.1)
18
- 22 (1.8 - 2.2)
18
- 22 (1 -8 - 2.2)
20
- 29 (2.0 - 3.0)
5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5
- 7.5 (0.56 - 0.76)
2) 5.5 - 7.5 (0.56 - 0.76)
(Tighten separately in twice.)
' Cylinder head boit
Cylinder head sub bolt
VTC solenoid
" Main bearing cap
Connecting rod
nut
Oil jet
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump (M6 bolt)
(M8 bolt)
(MI
0 bolt)
Water inlet
Oil pump assembly
Accelerator cable lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube
Front tube to catalytic
converter
Catalytic converter to center
tube
Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N.m (kg-m)
1) 29 (3.0)
2) 98 (10.0)
3) 0 (0)
4) 25 - 34 (2.5 - 3.5)
5) 95"
- 100"
(Angle tightening)
I%
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5)
49
- 59 (5.0 - 6.0) AT
1) 14 - 16 (1.4 - 1.6)
2) 60" - 65"
(Angle tightening) BR
30 - 40 (3.1 - 4.1)
93
- 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5) ST
25 - 34 (2.5 - 3.5)
3.8
- 4.5 (0.39 - 0.46) I%$
5.1 - 6.5 (0.52 - 0.66)
17
- 21 (1.7 - 2.1)
20
- 23 (2.0 - 2.3) kIA
35 - 47 (3.6 - 4.8)
16
- 21 (1.6 - 2.1)
9.0
- 12 (0.92 - 1.2) a=
': Tighten as specified tightening order.
1): Tighten separately in several times.