diagram NISSAN GT-R 1998 Owner's Manual

FULLY AUTOMATIC AIR CONDITIONER
Circuit
Diagram
Blower tan motor relay
Rear defogger
A Combination meter (meter UU) output * I Rear defogger relay - Rear defogger display inpui
I Compressor
Blower
fan driver signal Refrigerant Pressure sensor
Actuator driver power source
lntake driver
1 lntake driver 2 lntake driver 3 lntake driver 4
lntake door actuator NP ON output NP display input
Lighting
SW (1 step)
Y-lkEka Air mix door actuator
Illumination
power
source
Air mix driver 1 Air mrx drive: 2 Air mix driver 3 Air mix driver 4
Mode driver 1 1 Mode driver 2 Mode driver 3 Mode driver 4
INCAR In-vehicle sensor
Ambienl sensor
Sunload sensor
AM B
Water TEMP
SUN
INTAKE
Sensor around
lluminatron
groun:!
iND
Automatic
amp!iher

ELECTRICAL SYSTEM
SECTION EL
CONTENTS
CENTRAL DOOR LOCK SYSTEM ................................. 2
Component Parts Location .......................................... 2
Circuit Diagram ............................................................ 2
Combination Meter (meter control unit) Input/
Output Signal Specifications
........................................ 2
Inspection before Trouble Diagnoses ......................... -3
Trouble Diagnoses ....................................................... 3
REMOTE CONTROL ENTRY SYSTEM .......................... 4
Component Parts Location .......................................... 4
Circuit Diagram ............................................................ 4
Remote Control Entry Control Unit Input/Output
Signal Specifications
.................................................... 5
System Check ............................................................. -5
Inspection before Trouble Diagnoses .......................... 6
Trouble Diagnoses ....................................................... 6
Component Parts inspection ....................................... 6
ID Code Entry Procedure ............................................ 7
POWER WINDOW SYSTEM ........................................... 8
System Description ..................................................... -8
Precautions ................................................................. -8
Component Parts Location .......................................... 8
Circuit Diagram ............................................................ 9
Power Window Main Switch Input/Output Signal
Specifications
............................................................... 9
Inspection before Trouble Diagnoses ........................ 11
Trouble Diagnoses .................................................... 11
SUNROOF SYSTEM ...................................................... 12
Component Parts Location ........................................ 12
Circuit Diagram .......................................................... 12
Sunroof Switch and Sunroof Motor Assembly
lnputiOutput Signal Specifications
............................. 12
AUTO LIGHT SYSTEM ................................................. 1 3
Component Parts Location ........................................ 13
Auto Light Control Unit Input/Output Signal
Specifications
............................................................. 13
Circuit Diagram ........................................................ 14
Trouble Diagnoses .................................................. I 4
..................................... XENON HEADLAMP SYSTEM 15
Trouble Diagnoses ..................................................... 15
IGNITION KEY-OPERATED ILLUMINATION
SYSTEM
................................................................... 7
Component Parts Location ........................................ 17
.......................................................... Circuit Diagram 17
Meter Control Unit InputlOutput Signal
....................................................... Specifications 1 7
METER ........................................................................\
18
Corn bination Meter .................................................... 18
Triple Meter ................................................................ 20
................................................ COMBINATION METER 21
.................................................... System Description 21
........................................ Component Parts Location 21
Diagnosis Function .................................................... 21
................................... Meter-related Circuit Diagram 22
..................................................... Trouble Diagnoses 23
Combination Meter InpuVOutput Signal
Specifications
............................................................ -25
..................................... Component Parts Inspection 26
TRIPLE METER ............................................................. 29
Special Service Tool ................................................... 29
........................................ Component Parts Location 29
Circuit Diagram .......................................................... 29
Triple Meter InputfOutput Signal Specifications ........ 30
Component Parts Inspection ..................................... 30
IGNITION KEY WARNING BUZZER AND LIGHT
WARNING BUZZER
...................................................... 31
Component Parts Location ........................................ 31
Circuit Diagram .......................................................... 31
Meter Control Unit InpuVOutput Signal
Specifications
............................................................. 31
FRONT WIPER .............................................................. 32
Component Parts Location ........................................ 32
Circuit Diagram .......................................................... 32
Front Wiper Input/Output Signal Specifications ........ 32

CONTENTS (cm9d)
REAR WIPER ................................................................ 33 Meter Control Unit InpuVOutput Signal
Component
Parts Location ....................................... .33 Specifications -34 ............................................................
Circuit Diagram .......................................................... 33 WIPER DEICER ............................................................. 35
Rear Wiper Amplifier
Input/Output
Signal Component Parts Location
.35 @I .......................................
Specifications ............................................................ .33 Circuit Diagram 35 ..........................................................
REAR DEFOGGER AND HEATER MIRROR ............... 34 Wiper Deicer Switch InpuVOutput Signal
Component Parts Location ..34 Specifications.. 35 EG ...................................... ........................................................... .......................................................... Circuit Diagram 34

CENTRAL DOOR LOCK SYSTEM
Component
Parts Location
Door lock relay
LOCK -
Door lock relay
connector
1 LOCK 1
TK20 I I 5\41 1 (Brown) 1 11el j I 1
Combination meter
(Meter C/U) connector
I
Circuit Diagram
Driver door lock
Remote control entry
SW signal C/U connector
Lock signal
18. Unlock sign311 5 T 1
PMI main SW
(Central door lock SW)
----- I . RH door1
actuator 1 I I I Rear LH door I lock actuator I I I,,,,,,,------J
Driver door lock
actuator SW
P/'W main SW connector PNV main SW connector
(2-door Coupe) 1 (4-door Sedan) OCC3324 C
Combination Meter (meter control unit) Input/
Output Signal Specifications
-
I
. . 4 1 Driver door lock switch signal I
Specification
Approx. OV
Locked (OFF)
5
18
55
56
60
Operation or condition
Unlocked (ON1
Terminal No.
Approx.
5V
Signal name
Central door lock switch unlock signal
Central door lock switch lock signal
Ground Passenger and rear
RH 8 LH door lock
actuator lock signal
Passenger and rear RH & LH door lock actuator unlock siqnal Unlocked
(ON)
Operation other than above (OFF)
Locked (ON)
Operation other than above (OFF)
-
Central door lock switch is locked.
Central door lock switch is unlocked. Approx.
OV
Approx. 5V
Approx.
OV
Approx. 5V
Approx.
OV
Changes from approx. 12 to OV and back
to approx. 12V.
Changes from approx.
12 to OV and back
to approx. 12V.

REMOTE CONTROL ENTRY SYSTEM
1
Component Parts Location
Circuit Diagram
Key-in detection SW
Remote control entry I C/U connector -
Unlock signal

POWER WINDOW SYSTEM
Circuit Diagram
PiW SW power supply
I
.20(14) Lmt sw sgnai ")' Encoder power supply '8112 ' Encoder pulse signal I It>.
v Driver door PNV mot01
W (4-door Sedan)
Driver door
PMI motor
W
DOWN signal ~~~. Dz
UP signal 6 door P/W
( )' 2-door
Coupe DOWN signal
13 UP signal PMI maln SW connector 16 @-door Sedan) 9(11)
17 DOWN signal 2 -r UP signal Drrver I-------------J
I-
$ 4-door Sedan only
- 891011 141516 - Passenger door and
PiW
main
SW connector
(2-door Coupe) rear RH & LH
door
PiW SW connector OCC3265D 1
Power Window Main Switch Input/Output
Signal Specifications
Signal name
Limit switch and encoder
ground
( ): 2-door Coupe
Measurir
Ignition switch
ON or another position
(Timer is in operation.)
-
condition
Terminal No.
Specification
Operation or condition
Approx.
OV
Encoder pulse signal Approx.
2V
ON
or another position
(Timer is in operation.) Power window motor
is in
operation.
Driver door window is
between fully-open position and almost fully-closed
posit~on. (ON)
Driver door window is
between almost fully-closed position and fully-closed position. (OFF)
DOWN operation
Other than DOWN operation Approx.
OV
ON
or another position
(Timer is in operation.)
Lim~t
switch signal
Approx.
5V
Driver door power window
motor DOWN signal ON
or another position
(Timer is in operation.) Approx. 12V
Approx. OV
Approx. 12V Battery

I Sunroof motor assembly 1 Component Parts Location
I Sunroof switch < OCEM57DI
Circuit Diagram
CIB PMl relay
Sunroof motor assembly (Fully-closed position)
I I Limit SW 2 I -1 I i
3
5
1 1 -- LL
1 --
CLOSE relay - I ~irnitsw~ I
Sunroof SW
Slide SW
CLOSE 5--1
Sunroof Switch and Sunroof Motor Assembly
InputlOutput Signal Specifications
-
Measuring condition
I I
- Operation
Terminal No.
1
2
Ignition switch
3
4
5
ON
ON
'lased
ON
ON
ON Approx.
12V
OV
~~ll~ closed position to fully open position
Approx. 2V
OV
Approx. OV OV
OV
'Pen
Position
to fully closed
position
Approx.
OV (Motor is running.)
Approx. 2V
Approx. OV OV
OV
Fully closed position
to tilt UP position
Approx.
12V
Approx. OV (Motor is running.)
Approx.
OV
Tilt UP position to
fully closed position
Approx.
OV (Motor is running.)
12'
Approx. 12V
Approx.
OV (Motor is running.)
ov
OV
Approx. OV
ov
OV
Approx. OV

AUTO LIGHT SYSTEM
Circuit Diagram
Xenon
headlamp
relay
To clearance
lamp and
tail lamp
I---- I : High-voltage parts ----- EL-2163D
Trouble Diagnoses
SYMPTOM CHART
Symptom I Possible cause
I a Faulty auto light control unit power supply or ground harnesi
I Faulty auto light control unit
When outside
is dark, neither small lamps nor headlamps
tum
ON
by
auto light operation. [Lighting switch
(1ST
and 2ND)
is normal.]
When outside is dark, small lamps turn ON but headlamps do not turn
Faulty lighting switch to auto light control unit harness
ON by auto light operation. [Lighting switch (1 ST and 2ND) is normal.] Faulty auto light control unit
0 Faulty lighting switch Faulty lighting switch to auto light control unit harness a Faulty lighting switch ground harness
When outside is dark, headlamps turn ON but small lamps do not turn
ON by auto light operation. [Lighting switch
(1ST
and 2ND) is normal.]
Faulty lighting switch to auto light control unit hamess Faulty auto light control unit
a Neither headlamps nor small lamps turn OFF when the driver door is
opened with the ignition switch at ACC. a Headlamps and small lamps turn OFF when the ignition switch is
turned to ACC with the driver door closed.
0 While the vehicle is driven at night, headlamps go off momentarily
~~- - - pp a Faulty door switch a Faulty door switch to auto light control unit harness a Faulty door switch ground harness 0 Faulty auto light control unit
when it passes under street lamps.
0 While the vehicle is driven in the early morning or evening, headlamps
turn ON momentarily when it passes under an overpass or through a Faulty speedometer to auto light control unit harness a Faulty auto light control unit
building shadows.
During the day, neither small lamps nor headlamps turn OFF. During the day, headlamps tum OFF but small lamps do not turn OFF. a Faulty auto light control unit

XENON HEADLAMP SYSTEM
Trouble Diagnoses
DESCRIPTION
Problems with xenon headlamps are as follows:
They do not light up.
They blink.
GD
They are not bright enough.
In most cases the problems above are caused by faulty xenon bulbs.
There might be the possibility that the problems are caused by faulty HID control unit or lamp sockets.
ec
Follow the diagnostic procedure to determine what causes the problem.
PRECAUTIONS AT
Connect or disconnect connectors with the lighting switch OFF.
Do not touch harnesses, HID control unit, internal lamp, or metal part of the lamp while the lamps are
ON B2
(Lighting switch is ON).
Before verifying that the lamps are ON, install the parts to the vehicle temporarily and connect the battery
cable with
the connector on the vehicle. ST
If the electrical system is suspected to be the cause of the symptom, check for blown fuse or fusible link,
broken connectors, disconnected terminals, or faulty engagement.
Do not use wet hands when performing the trouble diagnoses.
F@
CIRCUIT DIAGRAM
, MA Xenon
headlamp
relay
To clearance
JJ$Rkj
lamp and
tail lamp
Headlamp
1 -- - -1 : High-voltage parts
Driver door SM
CAUTION:
0 Do not use a tester to diagnose the HID control unit circuit.
0 Do not disassemble the HID control unit and harnesses (bulb socket harness and control unit har-
ness).
0 Immediately after the headlamps turn ON, brightness and emission color vary. This is a normal
condition.
When a bulb has reached the end of its life, the brightness becomes extremely low, the bulb con-
tinues to blink, or the light looks reddish.

IGNITION KEY-OPERATED ILLUMINATION SYSTEM
Behind combination meter Component Parts Location
Meter control unit
Circuit Diagram
7, . .
& Driver door lock detection switch
T
2 1 r Passenger door SW Rear RH door SW 326
' a
Rear LH door SW
3 - -
Room lamp
IGN SW illumination
TK24 (Brown) TK20 (Brown) TK20 (White) EL-2 178D I 1 J
Meter Control Unit Input/Output Signal
Terminal No.
Specifications I I
Specification
Approx.
OV
Approx. 12V
Approx. OV
Approx. 5V
Approx. 12V
Approx. OV
Approx. 12V
Approx. 12V
Approx. OV
Approx. 12V
Approx. OV
Approx. OV
Approx. 12V
Approx. OV'
Approx. 12V
Measuring condition
Signal name Ignition
Operation or condition
switch
Driver door switch ON (Open)
OFF Driver door switch
signal OFF (Closed)
Driver door lock
sig-
Door is unlocked. (Switch ON)
nal OFF
Door is locked. (Switch OFF)
Battery OFF
-
Open a door. (ON)
Door switch signal
OFF
Close all the doors. (OFF)
Ignition power supply ON
-
Key-in detection Remove
the ignition key.
switch signal OFF
Insert the ignition key.
Ground ON
-
OFF Room lamp switch:
Insert the ignition key. Each door switch
Room lamp, ignition Neutral position ON
(Open)
OFF (Closed)
switch illumination
Remove the ignition key from the
signal
- lamp switch: Close all the doors. key cylinder.
Neutral position
Turn the ignition switch ON.