lock NISSAN NOTE 2016 Service Repair Manual

DLK-284
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
2. Loosen door hinge nuts (door side).
3. Adjust the surface height of rear door
according to the specifications provided.
4. Temporarily tighten door hinge nuts (door side).
5. Loosen door hinge nuts and bolts (body side).
6. Raise rear door at rear end to adjust clearance of rear door according to the specifications provided.
7. After adjustment tighten bolts and nuts to the specified torque. CAUTION:
• Apply touch-up paint (body color) to the head of hinge bolts and nuts.
• Check door hinge rotating point fo r poor lubrication. If necessary, apply a suitable multi-purpose
grease.
8. Install center pillar lower finisher. Refer to INT-25, "
CENTER PILLAR LOWER FINISHER : Removal and
Installation".
DOOR STRIKER
DOOR STRIKER : Removal and InstallationINFOID:0000000012430251
REMOVAL
Remove bolts and rear door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door striker bolts.
• Tighten door striker bolts to specification. Refer to DLK-281, "
Exploded View".
• After installation, check front door open/close oper ation. If necessary, adjust the door striker. Refer
to DLK-284, "
DOOR STRIKER : Adjustment".
DOOR STRIKER : AdjustmentINFOID:0000000012430252
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts.
2. Adjust door striker so that it becomes parallel with rear door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to DLK-281, "
Exploded View".
DOOR HINGE
DOOR HINGE : Removal and InstallationINFOID:0000000012430253
REMOVAL
CAUTION:
• Use two people when removing or installing front door due to its heavy weight
• When removing and installing front door assembly, support the door using a suitable tool.
• Use shops cloths to protect surrounding components from damage during removal and installation of front door assembly.
1. Remove rear door assembly. Refer to DLK-281, "
DOOR ASSEMBLY : Removal and Installation".
2. Remove center pillar lower finisher. Refer to INT-25, "
CENTER PILLAR LOWER FINISHER : Removal
and Installation".
PIIB2804J
Revision: August 2015 2016 Versa Note

cardiagn.com

BACK DOORDLK-287
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Remove back door harness grommet (1), then pull harness from the back door.
4. Disconnect washer tube from rear wiper.
5. Remove washer tube grommet (1), then pull washer tube from the back door.
6. Support the back door assembly using a suitable tool. WARNING:
Bodily injury may occur if back door assembly is not supported properly when removing the back
door spindle unit.
7. Remove back door hinge nuts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the su rface between hinge and door side.
• When reusing stud ball, always apply locking sealan t before installing stud ball to back door.
• After installation, perfor m the back door assembly adjustment procedure. Refer to DLK-288, "
BACK
DOOR ASSEMBLY : Adjustment".
ALKIA3187ZZ
ALKIA3188ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BACK DOORDLK-289
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Check the clearance and the surface height between back door and each part by visual inspection and tactile
feel. If the clearance and the surface height are out of specification, adjust them according to the adjustment
procedure.
Unit: mm (in)
1. Loosen back door hinge nuts (door side).
2. Lift up back door approximately 100 – 150 mm (3.94 – 5.91 in) height then close it lightly and check that it
is engaged firmly with back door closed.
3. Check the clearance and surface height and adjust back door as necessary.
4. Tighten back door hinge nuts to specified torque.
CAUTION:
• After installation, check back door open/close, lock/ unlock operation.
• Check back door hinge rotating po int for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
• After adjusting, apply touch-up paint (body color) to the head of rear door hinge bolts and nuts.
BACK DOOR STRIKER
BACK DOOR STRIKER : Removal and InstallationINFOID:0000000012430258
REMOVAL
1. Remove back door kicking plate using a suitable tool.
2. Remove bolts and back door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse back door striker bolts.
• After installation, check back door open/close, lock/ unlock operation.
• After installation, perfor m the back door assembly adjustment procedure. Refer to DLK-288, "
BACK
DOOR ASSEMBLY : Adjustment".
BACK DOOR STRIKER : AdjustmentINFOID:0000000012430259
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts.
2. Adjust door striker so that it becomes parallel with back door
lock insertion direction.
3. Tighten door striker bolts to specification. Refer to DLK-286, "
Exploded View".
PortionSection Item Measurement Standard
Back door panel – Roof panel A – A H
Clearance 6.0 ± 1.0 (0.24 ± 0.04)
I Surface height 0.0 +0.5, -1.5 (0.00 +0.02, -0.06)
Rear combination lamp – Back door panel B – B J
Clearance 5.0 ± 2.0 (0.20 ± 0.08)
K Surface height -2.0 ± 2.0 (-0.08 ± 0.08)
Rear bumper fascia – Back-door panel C – CL C
le a ra n ce 5 .0 ± 2.0 (0.20 ± 0.08)
M Surface height 0.0 +0.5, -2.0 (0.0 +0.02, -0.08)
D – D M Clearance7.0 ± 2.0 (0.28 ± 0.08)
PIIB2804J
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-292
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD LOCK
HOOD LOCK
Exploded ViewINFOID:0000000012430264
HOOD LOCK
HOOD LOCK : Removal and InstallationINFOID:0000000012430265
REMOVAL
1. Remove hood lock bolts (A).
2. Disconnect hood lock release cable (2) from hood lock (1) and
remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1. Hood lock/fuel filler lid release handle 2. Hood lock assembly 3. Hood lock release cable assembly
A. Clip
AWKIA2572ZZ
ALKIA3190ZZ
AWKIA2497ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

HOOD LOCKDLK-293
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
• After installation, perform hood assem bly adjustment procedure. Refer to DLK-269, "HOOD ASSEM-
BLY : Adjustment".
• After adjustment, perform hood lo ck control inspection. Refer to DLK-293, "
HOOD LOCK : Inspec-
tion".
HOOD LOCK : InspectionINFOID:0000000012430266
HOOD LOCK INSPECTION
NOTE:
If hood lock cable is bent or deformed, replace it. Refer to DLK-292, "
HOOD LOCK : Removal and Installa-
tion".
1. Check that secondary latch is properly engage with secondary striker with hoods own weight.
2. While operating hood lock release lever, carefully check that the front end of hood assembly is raised by approximately 20.0 mm (0.79 in). Also check that hood lock release lever returns to original position.
3. Check that hood lock release lever operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
4. Install so that static closing force of hood is 315-490 N (32.1-50.0 kg-m, 70.8-110.2 ft-lb).
5. Check hood lock assembly lubrication condition. If necessary, apply a suitable multi-purpose grease.
HOOD LOCK RELEASE CABLE
HOOD LOCK RELEASE CABLE : Removal and InstallationINFOID:0000000012430267
REMOVAL
1. Disconnect hood lock release cable from hood lock. Refer to DLK-292, "Exploded View".
2. Remove radiator cap adapter bracket bolt (A) and radiator reser- voir tank bolt (B).
3. Remove fender protector (LH). Refer to EXT-38, "
Removal and Installation".
4. Release hood lock control cable clips using a suitable tool.
5. Remove hood lock/fuel filler door release handle. Refer to DLK-167, "
HOOD LOCK RELEASE HANDLE :
Removal and Installation".
6. Remove dash side finisher (LH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
7. Remove grommet on the lower dash and pull the hood lock release cable into the passenger compart- ment.
CAUTION:
While pulling, be caref ul not to damage (peel) the outsi de of the hood lock release cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that hood lock release cable is properly engaged with hood lock.
JMKIA8027ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-294
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD LOCK
• Check that cable is not offset
from the positioning grommet,
and apply the sealant to the grommet (at * mark).
HOOD LOCK RE LEASE HANDLE
HOOD LOCK RELEASE HANDLE : Removal and InstallationINFOID:0000000012430268
REMOVAL
1. Remove hood lock/fuel filler door release handle bolts (A).
2. Disconnect hood lock release cable from hood lock/fuel filler door release handle and remove.
INSTALLATION
Installation is in the reverse order of removal.
PIIB5801E
AWKIA2498ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT DOOR LOCKDLK-295
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
FRONT DOOR LOCK
Exploded ViewINFOID:0000000012430269
DOOR LOCK
DOOR LOCK : Remova l and InstallationINFOID:0000000012430270
REMOVAL
1. Remove inside handle. Refer to DLK-296, "INSIDE HANDLE : Removal and Installation".
2. Remove outside handle. Refer to DLK-297, "
OUTSIDE HANDLE : Removal and Installation".
3. Disconnect the harness connector from the door lock actuator (if equipped).
4. Remove front door glass rear run. Refer to GW-21, "
Exploded View".
5. Remove bolts and door lock.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock bolts.
• After installation, check door open/close, lock/un lock operation.
• Check door lock cables are properly engaged to inside handle and outside handle bracket.
• When installing key cylinder on front door, be sure to rotate key cylinder rod holder until a click is
felt.
1. Key cylinder 2. Outside handle bracket 3. Front gasket
4. Outside handle 5. Inside handle 6. Door lock
7. Key cylinder rod 8. Rear gasket A. Clip
B. Bolt Pawl
AWKIA3161ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-296
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
• Check door lock for poor lubri
cation. Apply a suitable multi-
purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and InstallationINFOID:0000000012430271
REMOVAL
1. Remove front door finisher. Refer to INT-15, "Removal and Installation".
2. Partially remove vapor barrier. Refer to GW-21, "
Exploded View".
3. Release lock knob (2) and inside handle cable (3) from clip (1) using a suitable tool.
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel using a suitable tool and remove.
: Pawl
6. Release inside handle cable (3) and lock cable (2) from inside handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
JMKIA8077ZZ
JMKIA8078ZZ
AWKIA2500ZZ
JMKIA5885ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT DOOR LOCKDLK-297
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door open/close, lock/ unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000012430272
REMOVAL
1. Remove front door finisher. Refer to INT-15, "Removal and Installation".
2. Partially remove vapor barrier. Refer to GW-21, "
Exploded View".
3. Open rod holder (1) by pulling downward and separate key rod (3) from door lock assembly (2) (driver side only).
4. Release outside handle cable (1) from cable clip (A).
5. Remove door grommet (1) and bolt from grommet hole (2).
6. While pulling outside handle, remove outside handle escutch- eon.
JMKIA8080ZZ
AWKIA2574ZZ
JMKIA5888ZZ
JMKIA0560ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-298
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
7. While pulling outside handle (1), slide toward rear of vehicle to
remove.
8. Remove front gasket and rear gasket.
9. Slide outside handle bracket toward rear of vehicle to remove. : Front
10. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are prope rly engaged with outside handle bracket.
• After installation, check door op en/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com