battery NISSAN NOTE 2016 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 1473 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-346
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P059F ACTIVE GRILLE SHUTTER
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace the error-detec NISSAN NOTE 2016 Service Repair Manual EC-346
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P059F ACTIVE GRILLE SHUTTER
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace the error-detec](/img/5/57363/w960_57363-1472.png)
EC-346
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P059F ACTIVE GRILLE SHUTTER
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace the error-detected parts.
7.CHECK ACTIVE GRILLE SHUTTER
RELAY POWER SUPPLY CIRCUIT - 1
Check the voltage between active grille shutter harness connector and ground.
Is the inspection result normal?
YES >> GO TO 8.
NO >> GO TO 11.
8.CHECK ACTIVE GRILLE SHUTTER RELAY SIGNAL CIRCUIT - 1
1. Check the voltage between active grille shutter harness connector and ground as follows.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 9.
NO >> GO TO 12.
9.CHECK ACTIVE GRILLE SHUTTER RELAY GROUND CIRCUIT
1. Turn ignition switch OFF
2. Check the continuity between active grille shutter relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair or replace the error-detected parts.
10.CHECK ACTIVE GRILLE SHUTTER RELAY
Check active grille shutter relay. Refer to EC-347, "
Component Inspection (Active Grille Shutter Relay)".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Replace active grille shutter relay.
11 .CHECK ACTIVE GRILLE SHUTTE R RELAY POWER SUPPLY CIRCUIT - 2
1. Check 5A fuse (No. 27).
2. Check the continuity between active grille shutter relay harness connector and fuse socket.
+
−Vo l ta g e
(Approx.)
Active grille shutter relay
Connector Terminal E72 5Ground Battery voltage
+
−Condition Vo l ta g e
(Approx.)
Active grille shutter relay
Connector Terminal
E72 2 Ground Ignition switch: ON
Battery volt-
age
Ignition switch: OFF 0 V
+
−Continuity
Active grille shutter relay
Connector Terminal E72 1 Ground Existed
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1475 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-348
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P059F ACTIVE GRILLE SHUTTER
2. Remove active grille shutter relay.
3. Apply battery voltage to active grille shutter re
lay terminal, and check the continuity NISSAN NOTE 2016 Service Repair Manual EC-348
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P059F ACTIVE GRILLE SHUTTER
2. Remove active grille shutter relay.
3. Apply battery voltage to active grille shutter re
lay terminal, and check the continuity](/img/5/57363/w960_57363-1474.png)
EC-348
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P059F ACTIVE GRILLE SHUTTER
2. Remove active grille shutter relay.
3. Apply battery voltage to active grille shutter re
lay terminal, and check the continuity as follows.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace active grille shutter relay.
Active grille shutter relay ConditionContinuity
+–
Te r m i n a l
53 12 V direct current supply
between terminals 1 and 2
Existed
No current supply None
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1476 of 3641
![NISSAN NOTE 2016 Service Repair Manual P0603 ECMEC-349
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0603 ECM
DTC LogicINFOID:0000000012741284
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
TESTING C NISSAN NOTE 2016 Service Repair Manual P0603 ECMEC-349
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0603 ECM
DTC LogicINFOID:0000000012741284
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
TESTING C](/img/5/57363/w960_57363-1475.png)
P0603 ECMEC-349
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0603 ECM
DTC LogicINFOID:0000000012741284
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltag e is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 1 second.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Repeat step 1 and 2 for 10 times.
4. Turn ignition switch ON.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-349, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012741285
1.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT
Perform trouble diagnosis for ECM power supply and ground circuit. Refer to EC-159, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-42, "
Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-349, "
DTC Logic".
Is the 1st trip DTC
P0603 displayed again?
YES >> Replace ECM. Refer to EC-477, "Removal and Installation".
NO >> INSPECTION END
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P0603 ECM BACK UP CIRCUIT
[Internal control module keep
alive memory (KAM) error] • Malfunction in the internal back up RAM of ECM.
• Malfunction in the inte
rnal EEP-ROM system of
ECM. •ECM power supply
•ECM
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1477 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-350
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0604 ECM
P0604 ECM
DTC LogicINFOID:0000000012741286
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at l NISSAN NOTE 2016 Service Repair Manual EC-350
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0604 ECM
P0604 ECM
DTC LogicINFOID:0000000012741286
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at l](/img/5/57363/w960_57363-1476.png)
EC-350
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0604 ECM
P0604 ECM
DTC LogicINFOID:0000000012741286
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm th at battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON (engine stopped) and wait least 20 minutes. CAUTION:
Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-350, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012741287
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-350, "
DTC Logic".
Is the 1st trip DTC
P0604 displayed again?
YES >> Replace ECM. Refer to EC-477, "Removal and Installation".
NO >> INSPECTION END
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P0604 ECM
[Internal control module
random access memory
(RAM) error] Malfunction in the internal RAM of ECM.
ECM
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1478 of 3641
![NISSAN NOTE 2016 Service Repair Manual P0605 ECMEC-351
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0605 ECM
DTC LogicINFOID:0000000012741288
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn i NISSAN NOTE 2016 Service Repair Manual P0605 ECMEC-351
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0605 ECM
DTC LogicINFOID:0000000012741288
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn i](/img/5/57363/w960_57363-1477.png)
P0605 ECMEC-351
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0605 ECM
DTC LogicINFOID:0000000012741288
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltag e is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON (engine stopped) and wait least 20 minutes. CAUTION:
Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-351, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012741289
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-351, "
DTC Logic".
Is the 1st trip DTC
P0605 displayed again?
YES >> Replace ECM. Refer to EC-477, "Removal and Installation".
NO >> INSPECTION END
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P0605 ECM
[Internal control module
read only me
mory (ROM)
error] Malfunction in the internal ROM of ECM.
ECM
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1479 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-352
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0606 ECM
P0606 ECM
DTC LogicINFOID:0000000012741290
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at l NISSAN NOTE 2016 Service Repair Manual EC-352
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0606 ECM
P0606 ECM
DTC LogicINFOID:0000000012741290
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at l](/img/5/57363/w960_57363-1478.png)
EC-352
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0606 ECM
P0606 ECM
DTC LogicINFOID:0000000012741290
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm th at battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE-I
1. Turn ignition switch ON (engine stopped) and wait at least 10 seconds. CAUTION:
Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-352, "Diagnosis Procedure".
NO >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-II
1. Start engine.
2. Rev up the engine quickly to approximately 3,000 rpm under unloaded condition and completely release the accelerator pedal.
3. Let the engine idle and wait at least 10 seconds.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Turn ignition switch ON.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-352, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012741291
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure for 3 times. Refer to EC-352, "
DTC Logic".
Is the 1st trip DTC
P0606 displayed again?
YES >> Replace ECM. Refer to EC-477, "Removal and Installation".
NO >> INSPECTION END
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P0606 CONTROL MODULE
(Control module processor) Malfunction in ECM processor.
ECM
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1480 of 3641
![NISSAN NOTE 2016 Service Repair Manual P0607 ECMEC-353
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0607 ECM
DTC LogicINFOID:0000000012741292
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn i NISSAN NOTE 2016 Service Repair Manual P0607 ECMEC-353
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0607 ECM
DTC LogicINFOID:0000000012741292
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn i](/img/5/57363/w960_57363-1479.png)
P0607 ECMEC-353
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0607 ECM
DTC LogicINFOID:0000000012741292
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltag e is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-353, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012741293
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-353, "
DTC Logic".
Is the 1st trip DTC
P0607 displayed again?
YES >> Replace ECM. Refer to EC-477, "Removal and Installation".
NO >> INSPECTION END
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P0607 ECM
(Control module perfor-
mance) ECM internal communication system is malfunc-
tioning.
ECM
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1481 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-354
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P060A ECM
P060A ECM
DTC LogicINFOID:0000000012741294
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at l NISSAN NOTE 2016 Service Repair Manual EC-354
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P060A ECM
P060A ECM
DTC LogicINFOID:0000000012741294
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at l](/img/5/57363/w960_57363-1480.png)
EC-354
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P060A ECM
P060A ECM
DTC LogicINFOID:0000000012741294
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm th at battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait at least 10 seconds.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Repeat step 1 and 2 for 5 times.
4. Turn ignition switch ON.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-354, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012741295
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-354, "
DTC Logic".
Is the 1st trip DTC
P060A displayed again?
YES >> Replace ECM. Refer to EC-477, "Removal and Installation".
NO >> INSPECTION END
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P060A CONTROL MODULE
(Internal control module
monitoring processor per-
formance) ECM internal monitoring processor is malfunction-
ing.
ECM
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1482 of 3641
![NISSAN NOTE 2016 Service Repair Manual P060B ECMEC-355
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P060B ECM
DTC LogicINFOID:0000000012741296
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn i NISSAN NOTE 2016 Service Repair Manual P060B ECMEC-355
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P060B ECM
DTC LogicINFOID:0000000012741296
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn i](/img/5/57363/w960_57363-1481.png)
P060B ECMEC-355
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P060B ECM
DTC LogicINFOID:0000000012741296
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltag e is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-355, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012741297
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-355, "
DTC Logic".
Is the 1st trip DTC
P060B displayed again?
YES >> Replace ECM. Refer to EC-477, "Removal and Installation".
NO >> INSPECTION END
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P060B CONTROL MODULE
(Internal control module A/
D processing performance) ECM internal analog/digital conversion processing
system is malfunctioning.
ECM
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1483 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-356
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0643 SENSOR POWER SUPPLY
P0643 SENSOR POWER SUPPLY
DTC LogicINFOID:0000000012431554
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Co NISSAN NOTE 2016 Service Repair Manual EC-356
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0643 SENSOR POWER SUPPLY
P0643 SENSOR POWER SUPPLY
DTC LogicINFOID:0000000012431554
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Co](/img/5/57363/w960_57363-1482.png)
EC-356
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0643 SENSOR POWER SUPPLY
P0643 SENSOR POWER SUPPLY
DTC LogicINFOID:0000000012431554
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Go to EC-356, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431555
1.CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground Inspection in GI-44, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK SENSOR POWER SUPPLY
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector and ground.
DTC No. Trouble diagnosis content DTC detecting condition Possible cause
P0643 Sensor power supply circuit
short ECM detects a voltage of power
source for sensor is excessively low
or high. • Harness or connectors
(Accelerator pedal position 1 circuit is shorted.)
(Throttle position sensor 1 circuit is shorted.)
(Camshaft position sensor circuit is shorted.)
(Exhaust valve timing control position sensor cir-
cuit is shorted.)
(Engine oil pressure sensor circuit is shorted.)
• Accelerator pedal position sensor
• Throttle position sensor
• Camshaft position sensor
• Exhaust valve timing control position sensor
• Engine oil pressure sensor
Revision: August 2015 2016 Versa Note
cardiagn.com