ignition NISSAN NOTE 2016 Service Owner's Manual

AV
STEERING SWITCHAV-47
< DTC/CIRCUIT DIAGNOSIS > [BASE AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
3.CHECK COMBINATION SWITCH
Check continuity between combination switch connectors M88 and M30.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace spiral cable. Refer to SR-16, "
Removal and Installation".
4.CHECK HARNESS BETWEEN BLUETOOTH® CONTROL UNIT AND AUDIO UNIT
1. Disconnect audio unit connector M43.
2. Check continuity between Bluetooth
® control unit connector B33 and audio unit connector M43.
3. Check continuity between Bluetooth
® control unit connector B33 and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness or connectors.
5.CHECK AUDIO UNIT VOLTAGE
1. Connect Bluetooth
® control unit connector B33 and audio unit connector M43.
2. Turn ignition switch ON.
3. Check voltage between the terminals of audio unit connector M43.
Is the inspection result normal?
YES >> Replace audio unit. Refer to AV-53, "Removal and Installation".
NO >> Replace Bluetooth® control unit. Refer to AV-56, "Removal and Installation".
Combination switch
Continuity
Connector TerminalConnector Terminal
M88 14
M30 24
Ye s
15 31
17 33
Bluetooth® control unitAudio unit
Continuity
Connector TerminalConnector Terminal
B33 17
M43 6
Ye s
18 16
19 15
Bluetooth® control unit
Ground Continuity
Connector Terminal
B33 17
—N o
18
19
Audio unit connector M43
Vo l ta g e
(Approx.)
Terminal Terminal
6 15 5.0 V
16
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
NORMAL OPERATING CONDITIONAV-51
< SYMPTOM DIAGNOSIS > [BASE AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000012432888
RELATED TO NOISE
The majority of the audio concerns are the result of outside causes (bad CD, electromagnetic interference,
etc.).
The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.
• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.
• Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the antenna at a different time from the waves which reflect off mountains or buildings.
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
Type of Noise and Possible Cause
RELATED TO HANDS-FREE PHONE
Occurrence condition Possible cause
Occurs only when engine is ON. A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.
• Ignition components
The occurrence of the noise is linked with the operation of the fuel pump. • Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating. A cracking or snapping sound occurs with the op-
eration of various switches.
• Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing. • Motor case ground
•Motor
The noise occurs constantly, not just under certain conditions. • Rear defogger coil malfunction
• Open circuit in printed heater
• Poor ground of antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially when
it is vibrating excessively. • Ground wire of body parts
• Ground due to improper part installation
• Wiring connections or a short circuit
Symptom
Cause and Counter measure
Does not recognize cellular phone connection (No connection is
displayed on the display at the guide). Some Bluetooth
® enabled cellular phones may not be recognized
by the in-vehicle phone module.
Refer to “RELATED TO HANDS-FREE PHONE (Check Compati-
bility)” in AV- 4 8 , "
Symptom Table".
Cannot use hands-free phone. Customer will not be able to use a hands-free phone under the fol-
lowing conditions:
• The vehicle is outside of the telephone service area.
• The vehicle is in an area where it is difficult to receive radio
waves; such as in a tunnel, in an underground parking garage,
near a tall building or in a mountainous area.
• The cellular phone is locked to prevent it from being dialed.
NOTE:
While a cellular phone is connected through the Bluetooth
® wire-
less connection, the battery power of the cellular phone may dis-
charge quicker than usual. The Bluetooth
® Hands-Free Phone
System cannot charge cellular phones.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-62
< PRECAUTION >[DISPLAY AUDIO]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012432945
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Trouble DiagnosisINFOID:0000000012432946
AV COMMUNICATION SYSTEM
• Do not apply voltage of 7.0 V or higher to the measurement terminals.
• Use the tester with its open terminal voltage being 7.0 V or less.
• Be sure to turn ignition switch OFF and disconnect the battery cable from\
the negative terminal before checking the circuit.
Precaution for Harness RepairINFOID:0000000012432947
AV COMMUNICATION SYSTEM
• Solder the repaired parts, and wrap with tape. [Frays of twisted line
must be within 110 mm (4.33 in).]
PKIA0306E
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
DIAGNOSIS SYSTEM (AUDIO UNIT)AV-71
< SYSTEM DESCRIPTION > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
DIAGNOSIS SYSTEM (AUDIO UNIT)
DescriptionINFOID:0000000012432960
The audio unit on board diagnosis performs the functions listed in the table below:
On Board Diagnosis FunctionINFOID:0000000012432961
METHOD OF STARTING
1. Turn the ignition ON.
2. Turn the audio unit OFF.
3. While pressing the preset 1 button, turn the volume control dial clockwise and counterclockwise quickly approximately 15 times
or more. Shifting from current screen to previous screen is per-
formed by pressing BACK button.
4. The trouble diagnosis initial screen is displayed, and Self Diag- nosis or Confirmation/Adjustment can be selected.
SELF DIAGNOSIS MODE
Audio Unit Self Diagnosis
1. Select Self Diagnosis.
Mode Description
Self Diagnosis Audio unit diagnosis.
Confirmation/ Adjustment Display Diagnosis
The following check functions are available: color tone check by color
spectrum bar display and gray scale check by gradation bar display.
Vehicle Signals Diagnosis of signals can be performed for vehicle speed, lights, reverse,
EQ pin, ignition, destination and camera type.
Speaker Test The connection of a speaker can be confirmed by test tone.
Error History The system malfunction and the frequency when occurring in the past are
displayed. When the malfunctioning item is selected, the time and place
that the selected malfunction last occurred are displayed.
Camera System Guiding line position that overlaps rear view camera image can be adjust-
ed.
AV COMM Diagnosis Displayed but not used.
Delete Unit Connection Log Erase the connection history of unit and error history.
Version Information Displays the audio system version information.
Initialize Setting Initializes the audio unit memory.
ALNIA1710ZZ
JSNIA0138GB
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-74
< SYSTEM DESCRIPTION >[DISPLAY AUDIO]
DIAGNOSIS SYSTEM (AUDIO UNIT)
Select Speaker Test to display the Speaker Diagnosis screen. Press
Start to generate a test tone in a speaker. Press Start again to gener-
ate a test tone in the next speaker.
Press End to stop the test tones.
Error History
The self diagnosis results are judged depending on whether any error occurs from when Self Diagnosis is
selected until the self diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self diagnosis start. Check the Error Record to detect any error
that may have occurred before the self di agnosis start because of this situation.
The frequency of occurrence is displayed in a count up manner. The actual count up method differs depending
on the error item.
Count up method A
• The counter is set to 40 if an error occurs. 1 is subtracted from the counter if the condition is normal at a next ignition ON cycle.
• The counter lower limit is 1. The counter can be reset (no error record display) with the Delete log switch.
Count up method B• The counter increases by 1 if an error occurs when i gnition switch is ON. The counter will not decrease even
if the condition is normal at the next ignition ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. The counter can be reset (no error
record display) with the Delete log switch.
Error item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
Camera System
Use this mode to adjust the guide line display position of the rear
view monitor if necessary after removing the rear view camera.
Delete Unit Connection Log
AWNIA2634GB
Display type of occurrence frequency Error history display item
Count up method A AV communication line, control unit (AV)
Count up method B Other than the above
Error item DescriptionPossible cause
CONTROL UNIT (AV) AV communication circuit initial diagnosis
malfunction is detected.Replace the audio unit if the malfunction
occurs constantly.
Refer to
AV- 11 3 , "
Removal and Installation"
JSNIA1876ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-76
< ECU DIAGNOSIS INFORMATION >[DISPLAY AUDIO]
AUDIO UNIT
ECU DIAGNOSIS INFORMATION
AUDIO UNIT
Reference ValueINFOID:0000000012432962
TERMINAL LAYOUT
PHYSICAL VALUES
AWNIA3652ZZ
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
2
(GR) 3
(P) Sound signal front door
speaker LH
Output ON Sound output
4
(W) 5
(R) Sound signal rear door
speaker LH
Output ON Sound output
6
(SB) 15
(G) Steering switch signal A Input ON Press SOURCE switch
0V
Press switch 1.0V
Press switch 2.0V
Press switch 3.0V
Except above 5.0V
7
(W) Ground ACC power supply
Input ACC—Battery voltage
9
(R) 8
(B) Illumination control signal Input ON Headlamps ON
Battery voltage
SKIB3609E
SKIB3609E
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
AUDIO UNITAV-77
< ECU DIAGNOSIS INFORMATION > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P11
(BG) 12
(V) Sound signal front door
speaker RH
Output ON Sound output
13
(L) 14
(Y) Sound signal rear door
speaker RH
Output ON Sound output
16
(V) 15
(G) Steering switch signal B Input ON Press switch
0V
Press switch 1.0V
Press switch 2.0V
Except above 5.0V
18
(LG) Ground Vehicle speed signal Input ON When vehicle speed is ap-
prox. 40 km/h (25 MPH)
19
(Y) Ground Battery power supply Input OFF
—Battery voltage
20
(B/W) Ground Ground
— ON— 0 V
33
(B) Ground Camera ground
— ON — 0 V
34
(L) Ground Camera power supply Output ON Camera image displayed
6.0 V
Except for above 0 V
35
(Y) 36
(Shield) Camera image signal Input ON Camera image displayed
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
JSNIA0012GB
SKIB2251J
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-78
< ECU DIAGNOSIS INFORMATION >[DISPLAY AUDIO]
AUDIO UNIT
37
(P) 39
(Shield) Microphone signal
Input ONWhile speaking into micro-
phone.
38
(L) Ground MIC VCC
Output ON—5 V
44
(B) Ground Camera detection
— ON— 0 V
46
(B) Ground EQ02 Ground
— ON— 0 V
48
(B/W) Ground EQ04 Ground
— ON— 0 V
50
(Y) Ground Reverse signal
Input ONSelector lever in R (re-
verse)
Battery voltage
Selector lever in any posi-
tion other than R (reverse) 0 V
53
(B) — USB ground
— —— —
55
(G) — USB D+ signal
— —— —
56
(W) — USB D
− signal — — — —
57
(R) — V BUS signal
— —— —
58
(Shield) — USB shield
— —— —
60
(G) Ground AUX jack audio signal LH Input ON Received audio signal
(AUX input)
61
(L) Ground AUX jack audio signal RH Input ON Received audio signal
(AUX input)
62
(Y) Ground AUX ground
— ON— 0V
67
(B) Ground Antenna amp. ON signal Output ON Audio unit ON, FM-AM se-
lected.
Battery voltage
68
(B) Ground AM/FM antenna signal Input ON
Audio unit ON, FM-AM se-
lected.5.0 V
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
AUDIO UNITAV-79
< ECU DIAGNOSIS INFORMATION > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
69
(Shield) —
AM/FM antenna signal
shield —— —
—
72
(B) Ground Satellite antenna signal Input ON Audio unit ON, XM select-
ed.5.0 V
73
(Shield) — Satellite antenna shield — —
——
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
INSPECTION AND ADJUSTMENTAV-93
< BASIC INSPECTION > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
INSPECTION AND ADJUSTMENT
REGISTRATION (AUDIO UNIT)
REGISTRATION (AUDIO UNIT) : DescriptionINFOID:0000000012432965
AFTER REPLACEMENT
If the audio unit is replaced with a new audio unit, the new audio unit must be registered using the Bluetooth D/
C(serial #).
CAUTION:
If the new audio unit Bluetooth D/C(serial #) is not registered, the “APPS” mode will not function.
REGISTRATION (AUDIO UN IT) : Work ProcedureINFOID:0000000012432966
1.RECORD BLUETOOTH D/C(SERIAL #) FOR REPLACEMENT AUDIO UNIT
1. Turn ignition switch ON.
2. Turn audio unit OFF.
3. Access the diagnostic menu as follows:
- Press and hold preset buttons 2 and 3.
- While holding preset buttons 2 and 3, press preset button 5 three times.
4. Select Version Information from the Diagnostic Menu.
AWNIA3612ZZ
AWNIA3613ZZ
ALNIA1652ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com