camera image NISSAN NOTE 2016 Service Service Manual

AV
MULTI AV SYSTEMAV-231
< SYMPTOM DIAGNOSIS > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
Camera image is rolling. Camera image signal circuit (output)
malfunction. Camera image signal circuit (output) malfunction be-
tween around view monitor control unit and AV control
unit.
Refer to
AV- 1 5 2 , "
Reference Value".
Display does not switch to rear view
monitor even when selector lever is
in R (reverse). Reverse signal circuit malfunction. Reverse signal circuit between transmission range
switch (with CVT) or park/neutral position (PNP)
switch (back-up) (with M/T) and around view monitor
control unit.
Refer to
AV- 1 5 2 , "
Reference Value".
Predicted course line display in front
view and rear view is malfunction-
ing. Steering angle sensor malfunction. Predicted course line center position is malfunction-
ing.
Refer to
AV- 1 7 9 , "
PREDICTED COURSE LINE CEN-
TER POSITION ADJUSTMENT : Work Procedure".
Front view and front of birds-eye
view is not displayed. • Front camera malfunction.
• Front camera image signal circuit mal-
function. • Front camera power supply and ground circuits
malfunction.
• Front camera image signal circuit malfunction be- tween front camera and around view monitor con-
trol unit.
Refer to AV- 1 9 4 , "
Diagnosis Procedure".
Rear view and rear of birds-eye
view is not displayed. • Rear view camera malfunction.
• Rear view camera image signal circuit
malfunction. • Rear view camera power supply and ground cir-
cuits malfunction.
• Rear view camera image signal circuit malfunction between rear view camera and around view moni-
tor control unit.
Refer to AV- 1 8 8 , "
Diagnosis Procedure".
Driver side of birds-eye view is not
displayed. • Side camera LH malfunction.
• Side camera LH image signal circuit
malfunction. • Side camera LH power supply and ground circuits
malfunction.
• Side camera LH image signal circuit malfunction
between side camera LH and around view monitor
control unit.
Refer to AV- 1 9 6 , "
Diagnosis Procedure".
Front-side and passenger side of
birds-eye view is not displayed. • Side camera RH malfunction.
• Side camera RH image signal circuit
malfunction. • Side camera RH power supply and ground circuits
malfunction.
• Side camera RH image signal circuit malfunction between side camera RH and around view monitor
control unit.
Refer to AV- 1 9 2 , "
Diagnosis Procedure".
Selector lever is in a position other
than R (reverse) and front, rear,
front-side and Birds-Eye views are
displayed even as vehicle speed in-
creases. Vehicle speed signal malfunction.
Vehicle speed signal malf
unction between ABS actu-
ator and electric unit (control unit) and around view
monitor control unit.
Refer to AV- 1 5 2 , "
Reference Value".
Symptoms
Check items Probable malfunction location
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-242
< REMOVAL AND INSTALLATION >[NAVIGATION]
AV CONTROL UNIT
• Perform camera image calibration. Refer to
AV-179, "CALIBRATING CAMERA IMAGE (AROUND
VIEW MONITOR) : Work Procedure".
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
AROUND VIEW MONITOR CONTROL UNITAV-249
< REMOVAL AND INSTALLATION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
AROUND VIEW MONITOR CONTROL UNIT
Removal and InstallationINFOID:0000000012433101
REMOVAL
1. Remove the front passenger seat. Refer to SE-22, "PASSENGER SIDE : Removal and Installation".
2. Remove the floor trim. Refer to INT-27, "
Removal and Installation".
3. Disconnect the harness connector from the around view monitor control unit.
4. Remove the screws (A) from the around view monitor control unit bracket and remove.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Perform camera image calibration. Refer to AV- 1 7 9 , "
CALIBRATING CAMERA IMAGE (AROUND VIEW
MONITOR) : Work Procedure".
AWNIA3074ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-250
< REMOVAL AND INSTALLATION >[NAVIGATION]
FRONT CAMERA
FRONT CAMERA
Removal and InstallationINFOID:0000000012433102
REMOVAL
1. Remove the front grille. Refer to
EXT-32, "Removal and Installation".
2. Remove the front camera screws (A) and remove.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Perform camera image calibration. Refer to AV-179, "
CALIBRATING CAMERA IMAGE (AROUND VIEW
MONITOR) : Work Procedure".
AWNIA3075ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
REAR VIEW CAMERAAV-251
< REMOVAL AND INSTALLATION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
REAR VIEW CAMERA
Removal and InstallationINFOID:0000000012433103
REMOVAL
1. Remove the back door outer finisher. Refer to EXT-48, "Removal and Installation".
2. Disconnect the harness connector from rear view camera.
3. Remove the nuts (A) from the rear view camera and remove.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Perform camera image calibration. Refer to AV- 1 7 9 , "
CALIBRATING CAMERA IMAGE (AROUND VIEW
MONITOR) : Work Procedure".
AWNIA3070ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

A V -252
< REMOVAL AND INSTALLATION >[NAVIGATION]
SIDE CAMERA
SIDE CAMERA
Exploded ViewINFOID:0000000012433104
Removal and InstallationINFOID:0000000012433105
REMOVAL
1. Remove the door mirror. Refer to
MIR-15, "Removal and Installation".
2. Remove the door mirror glass.
3. Remove the door mirror actuator.
4. Disconnect the harness connector from the side camera.
5. Remove the side camera screws and remove.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Perform camera image calibration. Refer to AV-179, "
CALIBRATING CAMERA IMAGE (AROUND VIEW
MONITOR) : Description".
1. Door mirror rear finisher 2.Side turn signal lamp (if
equipped)
3. Door mirror
4. Door mirror glass 5. Side camera 6. Door mirror base finisher
Pawl
AWLIA2708ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-150
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
Installation is in the reverse order of removal.
CAUTION:
• After installation, perform the front
door adjustment procedure. Refer to DLK-150, "
DOOR ASSEM-
BLY : Adjustment".
• Perform camera image calibration (if equipp ed with around view camera). Refer to AV-179, "
CALI-
BRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description".
• Apply anticorrosive agent to the door hinge mating surface.
• Check door hinge rota ting point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR ASSEMBLY : AdjustmentINFOID:0000000012430097
JMKIA8072ZZ
1. Front fender 2. Front door 3. Rear door
AWKIA2493ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-160
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
3. Remove back door harness grommet (1), then pull harness from
the back door.
4. Disconnect washer tube from rear wiper.
5. Remove washer tube grommet (1), then pull washer tube from the back door.
6. Support the back door assembly using a suitable tool. WARNING:
Bodily injury may occur if back door assembly is not supported properly when removing the back
door spindle unit.
7. Remove back door hinge nuts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the surface between hinge and door side.
• When reusing stud ball, always apply locking sealan t before installing stud ball to back door.
• After installation, perform the back door assembly adjustment procedure. Refer to DLK-161, "
BACK
DOOR ASSEMBLY : Adjustment".
• Perform camera image calibration (if equipp ed with around view camera). Refer to AV-179, "
CALI-
BRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description".
ALKIA3187ZZ
ALKIA3188ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-32
< REMOVAL AND INSTALLATION >
FRONT GRILLE
FRONT GRILLE
Exploded ViewINFOID:0000000012432169
Removal and InstallationINFOID:0000000012432170
REMOVAL
1. Remove the front grille finisher clips.
2. Release pawls using a suitable tool and remove the front grille finisher.
3. Disconnect the harness connector from the front camera (if equipped).
4. Release the clips using a suitable tool, then pull the front grille away from vehicle to release pawls andremove.
5. Release pawls and remove front emblem from front grille (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Perform camera image calibration (if equipp ed with around view camera). Refer to AV-179, "
CALI-
BRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description".
1. Front grille finisher2. Front grille 3. Front emblem
4. Front camera (if equipped) ClipPawl
AWKIA2554ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

MIR-16
< REMOVAL AND INSTALLATION >
DOOR MIRROR
6. Remove the door mirror outer bolts (A) and the door mirror (1).
7. Remove side camera (if necessary). Refer to AV-252, "
Removal
and Installation".
INSTALLATION
Installation is in the reverse order or removal.
CAUTION:
• Visually check door mirror base cover pawls fo r deformation and damage during installation.
• Perform camera image calibration (if equipp ed with around view camera). Refer to AV-179, "
CALI-
BRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description".
AWLIA2181ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com