battery NISSAN NOTE 2016 Service Manual PDF

BCS-86
< SYSTEM DESCRIPTION >[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
OUTLINE
• BCM incorporates a power saving control function t
hat reduces the power consumption according to the
vehicle status.
• BCM switches the status (control mode) by itself wit h the power saving control function. It performs the sleep
request to each unit (IPDM E/R and combination mete r) that operates with the ignition switch OFF.
Normal mode (wake-up)- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
• The reading interval of each switch changes from 10 ms interval to 60 ms interval.
SLEEP MODE ACTIVATION
• BCM receives the sleep-ready signal (ready) from IPDM E/R and combination meter via CAN communica-
tion.
• BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful- filled.
• Each unit stops the transmission of CAN communication with the sleep wake-up signal. BCM is in CAN com- munication sleep mode.
• BCM is in the low power consumption mode and perform s the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.
Sleep condition
WAKE-UP OPERATION
• BCM transmits the sleep wake up signal (wake up) to each unit when any of the wake-up conditions are ful- filled. It changes from the low power consumption mode to the normal mode.
• Each unit starts the transmission of CAN communica tion with the sleep wake up signal. Each unit transmits
the wake up signal to BCM via CAN communication to report the CAN communication start.
CAN sleep condition BCM sleep condition
• Receiving the sleep-ready signal (ready) from all units
• Ignition switch: OFF
• Vehicle security system alarm: No operation
• Warning lamp: Not operation
• Stop lamp switch: OFF
• Turn signal indicator lamp: No operation
• Exterior lamp: OFF
• Door lock status: No change
• CONSULT communication status: No communication
• Door switch status: No change
• Rear window defogger: OFF
• Driver door lock status: No change
• Key switch status: No change • Interior room lamp battery saver: Time out
• RAP system: OFF
• Nissan Vehicle Immobilizer System (NVIS) - NATS: No opera-
tion
• Remote keyless entry receiver communication status: No com- munication
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-88
< SYSTEM DESCRIPTION >[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
TRANSIT MODE CONTROL SYST EM : System Description
INFOID:0000000012432369
DESCRIPTION
Transit mode is a BCM function that disables several elec trical functions such as door lock/unlock by remote,
back door open by remote, panic alarm, anti-theft alarm, etc. Vehicles are shipped with the BCM in transit
mode to help prevent the battery from becoming discharged during dealer storage.
DETERMINING TRANSIT MODE STATUS
Use the table below to determine the transit mode status.
CANCELING TRANSIT MODE
NOTE:
Transit mode can only be canceled. Once transit mode has been canceled, it cannot be activated again.
To cancel transit mode, refer to BCS-126, "
Work Procedure".
Status Symptom
Transit Mode When ignition switch is turned from OFF to ON, turn signal indicators will illuminate for 1 minute.
Normal Mode (not in transit mode) When ignition switch is turned from OFF to ON, turn signal indicators stay OFF (do not illumi-
nate).
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
DIAGNOSIS SYSTEM (BCM)BCS-89
< SYSTEM DESCRIPTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)INFOID:0000000012432370
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
Description
ECU Identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
System Sub System Direct Diagnostic Mode
ECU Identification
Self Diagnostic Result
Data Monitor
Active Test
Work support
Configuration
CAN DIAG SUPPORT MNTR
Door lock
DOOR LOCK ×××
Rear window defogger REAR DEFOGGER ××
Warning chime BUZZER ××
Interior room lamp timer INT LAMP ×××
Remote keyless entry system MULTI REMOTE ENT ×××
Exterior lamp HEAD LAMP ×××
Wiper and washer WIPER ×××
Turn signal and hazard warning lamps FLASHER ××
Air conditioner AIR CONDITIONER ×
Combination switch COMB SW ×
BCM BCM× × ×××
Immobilizer IMMU ×××
Interior room lamp battery saver BATTERY SAVER ×××
Vehicle security system THEFT ALM ××
RAP system RETAINED PWR ××
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR ××××
Panic alarm system PANIC ALARM ×
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-94
< SYSTEM DESCRIPTION >[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
WORK SUPPORT
* : Initial setting
WIPER
WIPER : CONSULT Function (BCM - WIPER)INFOID:0000000012432377
DATA MONITOR
Monitor Item [Unit]
Description
IGN ON SW [On/Off] Indicates condition of ignition switch ON position.
ACC ON SW [On/Off] Indicates condition of ignition switch ACC position.
HI BEAM SW [On/Off]
Indicates condition of combination switch.
HEAD LAMP SW 1 [On/Off]
HEAD LAMP SW 2 [On/Off]
TAIL LAMP SW [On/Off]
PASSING SW [On/Off]
FR FOG SW [On/Off]
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off] Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off] Indicates condition of back door switch.
TURN SIGNAL R [On/Off] Indicates condition of combination switch.
TURN SIGNAL L [On/Off]
KEY ON SW [On/Off] Indicates condition of key switch.
KEYLESS LOCK [On/Off] Indicates condition of lock signal from keyfob.
PKB SW [On/Off] Indicates park brake switch signal received from combination meter on CAN communica-
tion line.
ENGINE RUN [On/Off] Indicates engine run signal received from ECM on CAN communication line.
VEHICLE SPEED [km/h/mph] Indicates vehicle speed signal received from combination meter on CAN communication
line.
Test Item
Description
TAIL LAMP This test is able to check tail lamp operation [On/Off].
HEAD LAMP This test is able to check head lamp operation [Hi/Low/Off].
FR FOG LAMP This test is able to check front fog lamp operation [On/Off].
ILL DIM SIGNAL This test is able to check head lamp illumination dimming operation [On/Off].
Support ItemSetting Description
BATTERY SAVER SET On*
Exterior lamp battery saver function ON.
Off Exterior lamp battery saver function OFF.
Monitor Item [Unit] Description
IGN ON SW [On/Off] Indicates condition of ignition switch ON position.
IGN SW CAN [On/Off] Indicates ignition switch ON signal received from IPDM E/R on CAN communication line.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
DIAGNOSIS SYSTEM (BCM)BCS-97
< SYSTEM DESCRIPTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
IMMU : CONSULT Function (BCM - IMMU)INFOID:0000000012432382
SELF DIAGNOSTIC RESULT
Refer to
BCS-115, "DTCIndex".
ACTIVE TEST
WORK SUPPORT
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)INFOID:0000000012432383
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
* : Initial setting
THEFT ALM
Test Item Description
THEFT IND This test is able to check security indicator operation [On/Off].
Support ItemSetting Description
CONFIRM DONGLE ID —Dongle ID code can be read.
Monitor Item [Unit] Description
IGN ON SW [On/Off] Indicates condition of ignition switch ON position.
KEY ON SW [On/Off] Indicates condition of key switch.
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off] Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off] Indicates condition of back door switch.
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off] Indicates condition of unlock signal from door lock and unlock switch.
KEYLESS LOCK [On/Off] Indicates condition of lock signal from keyfob.
KEYLESS UNLOCK [On/Off] Indicates condition of unlock signal from keyfob.
KEY CYL LK-SW [On/Off] Indicates condition of lock signal from door key cylinder switch.
KEY CYL UN-SW [On/Off] Indicates condition of unlock signal from door key cylinder switch.
ACC SW [On/Off] Indicates condition of ignition switch ACC position.
Test item Description
BATTERY SAVER This test is able to check battery saver operation [On/Off].
Support ItemSetting Description
ROOM LAMP TIMER SET MODE 3* 10 min.
Sets interior room lamp battery saver timer operating time.
MODE 2 60 min.
MODE 1 15 min.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-106
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
52
(G)Ground Input 2 signal Input
Combination
switchOFF
0 V
FR WASHER
1.0 V
RR WASHER
RR WIPER ON
6
1
(R) Ground Input 1 signal Input
Combination
switchOFF
0 V
FR WIPER HI
1.0 V
Wiper intermittent dial 1
Wiper intermittent dial 2
Wiper intermittent dial 3
Wiper intermittent dial 6
Wiper intermittent dial 7
RR WIPER INT
6
2
(R) Ground Input 1 signal Input
Combination
switchOFF
0 V
FR WIPER HI
1.0 V
RR WIPER INT
7
(W) Ground Key cylinder unlock
sw signal InputKey cylinder
switch N position
7.0 - 8.0 V
UNLOCK position 0 V
8
(GR) Ground
Key cylinder lock sw
signal Input
Key cylinder
switch N position
7.0 - 8.0 V
LOCK position 0 V
9
(LG) Ground Brake sw 1 signal Input Sto p l am p
switchOFF (brake pedal re-
leased)
0 V
ON (brake pedal de-
pressed) Battery voltage
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4958J
PKIB4958J
PKIB4958J
PKIB4960J
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-107
< ECU DIAGNOSIS INFORMATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
10
(G) Ground
Rear defogger sw
signal Input
Rear window
defogger switch OFF
Battery voltage
ON 0 V
11
(L) Ground ACC switch signal Input Ignition switch OFF
0 V
ACC or ON Battery voltage
12
(GR) Ground Central door lock sw
signal InputDoor lock and
unlock switch N position
1.0 - 1.5 V
LOCK position 0 V
13
(BR) Ground Central door unlock
sw signal InputDoor lock and
unlock switch N position
1.0 - 1.5 V
UNLOCK position 0 V
18
(V) Ground Keyless gnd signal Input Ignition switch ON
0 V
19
(LG) Ground
Keyless tuner power
supply Input
Ignition switch
OFF Key inserted into ignition
key cylinder
0 V
Key removed from ignition
key cylinder
(Any door open) 5 V
Key removed from ignition
key cylinder
(Any door closed)
Terminal No.
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
JPMIA0012GB
JPMIA0012GB
JPMIA0338JP
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-108
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
20
(G) Ground Keyless tuner signal Input Ignition switch
OFFKey inserted into ignition
key cylinder
0 V
Waiting
Signal receiving
21
(P) Ground Immobilizer one way
communication
(clock) signal Input/
Output While waiting Turn ignition switch ON.
Turn ignition switch ON: Pointer
of tester should move.
23
(GR) Ground Security indicator
output signal
InputSecurity indica-
tor ON
0 V
Blinking (Ignition switch
OFF) 11.3 V
OFF Battery voltage
24
(SB) Ground Audio/dongle link
(serial) signal Input/
Output Ignition switch OFF.
5 V
25
(LG) Ground Immobilizer two way
communication sig-
nal Input/
Output While waiting Turn ignition switch ON. Turn ignition switch ON: Pointer
of tester should move.
26
(O) Ground
THERMO amp. sig-
nal InputPush-button ig-
nition switch ON
and blower fan
switch ON A/C switch OFF
Battery voltage
A/C switch ON 0 V
27
(V) Ground
Air conditioner
switch signal Input A/C switch OFF
Battery voltage
ON 0 V
28
(SB) Ground Blower fan sw signal Input Fan switch OFF
0 V
I, II, III or IIII 7.0 - 8.0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PIIB7728J
PIIB7729J
JPMIA0014GB
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-109
< ECU DIAGNOSIS INFORMATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
29
(BG) Ground Hazard sw signal Input Hazard switch OFF
Battery voltage
ON 0 – 1.5 V
31
(LG) Ground Front defrost switch Input
——
32
1
(P) Ground Output 5 signal Output
Combination
switchOFF
7.0 - 8.0 V
FR FOG
1.2 V
RR WIPER ON
Wiper intermittent dial 1
Wiper intermittent dial 2
Wiper intermittent dial 6
Wiper intermittent dial 7
32
2
(P) Ground Output 5 signal Output
Combination
switchOFF
7.0 - 8.0 V
RR WIPER ON 1.2 V
Terminal No.
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4960J
PKIB4958J
PKIB4960J
PKIB4958J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-112
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
36
(LG) Ground Output 1 signal Output
Combination
switchOFF
7.0 - 8.0 V
FR WASHER
1.2 V
FR WIPER LOW
TURN LH
TURN RH
37
(Y) Ground Key sw signal Input Ignition switch Ignition key inserted into
ignition key cylinder
Battery voltage
Ignition key removed from
ignition key cylinder 0 V
38
(O) Ground Ign sw signal
Input Ignition switchOFF or ACC
0 V
ON or START Battery voltage
39
(L) Ground CAN high
Input/
Output ——
40
(P) Ground CAN low Input/
Output ——
41
(G) Ground Door unlock output
(DR) signal OutputFront door lock
actuator LH Actuated to UNLOCK po-
sition
Battery voltage
Other than actuated to
UNLOCK position 0 V
42
(Y) Ground Battery (FUSE) Input Ignition switch OFF
Battery voltage
43
(W) Ground Battery saver output
signal
OutputInterior room lamp battery saver activated
0 V
Interior room lamp battery saver not activat-
ed Battery voltage
44
(GR) Ground Rear defogger relay
output signal InputRear window
defogger switch OFF
Battery voltage
ON 0 – 0.5 V
45
(R) Ground Room lamp output
signal OutputInterior room
lamp or map
lamp OFF
Battery voltage
ON Battery voltage
DOOR 0 – 1 V
48
(L) Ground A/C indicator
Input— —
50
(G) Ground Battery (F/L)
Input Ignition switch OFF Battery voltage
52
(L) Ground Power window pow-
er supply (RAP) sig-
nal Output Ignition switch ON
Battery voltage
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx. )
Sign al

name Input/
Output
+ −
PKIB4960J
PKIB4958J
Revision: August 2015 2016 Versa Note

cardiagn.com