engine oil NISSAN NOTE 2016 Service Manual PDF
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 1109 of 3641
![NISSAN NOTE 2016 Service Manual PDF EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
• Remove connecting rod cap and bearing, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The proce](/img/5/57363/w960_57363-1108.png "NISSAN NOTE 2016 Service Manual PDF EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
• Remove connecting rod cap and bearing, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The proce")
EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
• Remove connecting rod cap and bearing, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the “Method by Calculation”.
MAIN BEARING OIL CLEARANCE
Method by Calculation
• Install main bearings (3) to cylinder block (1) and main bearing cap(2), and tighten main bearing cap bolts to the specified torque.
Refer to EM-94, "
Disassembly and Assembly".
• Measure the inner diameter (B) of main bearing (3) using suitable tool.
(Bearing oil clearance) = (Main bearing inner diameter) – (Crank-
shaft main journal diameter)
• If clearance exceeds the limit, select proper main bearing according to main bearing inner diameter and
crankshaft main journal diameter to obtain specified bearing oil clearance. Refer to EM-124, "
Main Bearing".
Method of Using Plastigage
• Remove engine oil and dust on crankshaft main journal and the surfaces of each bearing completely.
• Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding oil
holes.
• Install main bearings to cylinder block and main bearing cap, and tighten main bearing cap bolts to the spec- ified torque. Refer to EM-94, "
Disassembly and Assembly".
CAUTION:
Do not rotate crankshaft.
• Remove main bearing cap and bearings, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the “Method by Calculation”.
MAIN BEARING CRUSH HEIGHT
PBIC3276J
(A) : Example
(B) : Inner diameter measuring direction
Standard and Limit : Refer to EM-124, "Main Bearing".
PBIC3277J
PBIC3278J
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1117 of 3641
![NISSAN NOTE 2016 Service Manual PDF EM-116
< SERVICE DATA AND SPECIFICATIONS (SDS) [HR16DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:00](/img/5/57363/w960_57363-1116.png "NISSAN NOTE 2016 Service Manual PDF EM-116
< SERVICE DATA AND SPECIFICATIONS (SDS) [HR16DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:00")
EM-116
< SERVICE DATA AND SPECIFICATIONS (SDS) [HR16DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000012431742
GENERAL SPECIFICATIONS
Va l v e Ti m i n g
Unit: degree
( ): Valve timing control “ON”
Drive BeltINFOID:0000000012431743
DRIVE BELT
Belt Deflection
*: When engine is cold.Engine type
HR16DE
Cylinder arrangement In-line 4
Displacement cm
3 (cu in)1,598 (97.51)
Bore and stro ke mm (in)78.0× 83.6 (3.071 × 3.291)
Valve arrangement DOHC
Firing order 1-3-4-2
Number of piston rings Compression
2
Oil 1
Compression ratio 9.8:1
Compression pressure
kPa (kg/cm
2, psi) / 200 rpm Standard 1,510 (15.4, 219)
Minimum
1,270 (12.95, 184)
Differential limit between cylinders 100 (1.0, 14.5)
Va l v e t i m i n g
: Intake valve
: Exhaust valve
ab c d e f
216 228 11 (
−27)
AT D C 59 (-21)
ABDC -1 (49)
AT D C 37 (-13)
BBDC
JPBIA4228ZZ
Location Deflection adjustment *
Unit: mm (in)
Used belt New belt
Limit After adjusted
Drive belt With A/C
10.0 (0.39) 4.9 - 5.2 (0.19 - 0.20) 4.1 - 4.4 (0.16 - 0.17)
Without A/C 9.1 (0.36)4.3 - 4.7 (0.17 - 0.19) 3.7 - 3.9 (0.146 - 0.154)
Applied pushing force 98.1 N (10.0 kg-f, 22.0 lb-f)
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1128 of 3641
EC-1
ENGINE
C
DE
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
HR16DE
PRECAUTION ....... ........................................
8
PRECAUTIONS .............................................. .....8
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
8
On Board Diagnostic (OBD) System of Engine
and CVT ....................................................................
8
General Precautions .................................................9
PREPARATION ...........................................12
PREPARATION .............................................. ....12
Special Service Tools .......................................... ....12
Commercial Service Tools ......................................12
SYSTEM DESCRIPTION .............................14
COMPONENT PARTS ................................... ....14
ENGINE CONTROL SYSTEM ............................... ....14
ENGINE CONTROL SYSTEM :
Component Parts Location ....................................
14
ENGINE CONTROL SYSTEM : Component De-
scription ............................................................... ....
17
Accelerator Pedal Position Sensor ..........................18
Air Fuel Ratio Sensor 1 ...........................................19
Air Fuel Ratio Sensor 1 Heater ...............................19
Camshaft Position Sensor .......................................19
Clutch Pedal Position Switch ..................................20
Cooling Fan .............................................................20
Crankshaft Position Sensor .....................................20
ECM .................................................................... ....20
Electric Throttle Control Actuator ............................21
Engine Coolant Temperature Sensor ......................21
Engine Oil Pressure Sensor ....................................21
Engine Oil Temperature Sensor ..............................21
EVAP Canister Purge Volume Control Solenoid
Valve ................................................................... ....
22
EVAP Canister Vent Control Valve .........................22
EVAP Control System Pressure Sensor ..................22
Exhaust Valve Timing Cont rol Solenoid Valve ........23
Fuel Injector ......................................................... ....23
Fuel Pump ...............................................................23
Heated Oxygen Sensor 2 ........................................24
Heated Oxygen Sensor 2 Heater ............................24
Ignition Coil With Power Transistor .........................24
Intake Air Temperature Sensor ...............................24
Intake Valve Timing Control Solenoid Valve ...........25
Knock Sensor ...................................................... ....25
Battery Current Sensor (With Battery Tempera-
ture Sensor) .............................................................
25
Malfunction Indicator Lamp (MIL) ............................26
Mass Air Flow Sensor ..............................................26
Oil Pressure Warning Lamp ....................................26
Refrigerant Pressure Sensor ............................... ....27
Stop Lamp Switch & ASCD Brake Switch ...............27
Throttle Control Motor .......................................... ....27
Throttle Control Motor Relay ...................................27
Throttle Position Sensor ..........................................27
ASCD Steering Switch .............................................27
STRUCTURE AND OPERATION .....................28
Positive Crankcase Ventilation ................................28
On Board Refueling Vapor Recovery (ORVR) ........29
SYSTEM ............................................................30
ENGINE CONTROL SYSTEM ........................ ...........30
ENGINE CONTROL SYSTEM : System Diagram ....30
ENGINE CONTROL SYSTEM : System Descrip-
tion ...........................................................................
31
MULTIPORT FUEL INJECTION SYSTEM ................31
MULTIPORT FUEL INJECTION SYSTEM :
System Diagram ................................................. ....
32
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description ........................................................
32
ELECTRIC IGNITION SYSTEM .................................35
ELECTRIC IGNITION SYSTEM :
System Diagram ................................................. ....
35
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1129 of 3641
EC-2
ELECTRIC IGNITION SYSTEM : System De-
scription ............................................................... ...
35
AIR CONDITIONING CUT CONTROL ................... ...36
AIR CONDITIONING CUT CONTROL : System
Diagram ..................................................................
37
AIR CONDITIONING CUT CONTROL : System
Description ..............................................................
37
CAN COMMUNICATION ........................................ ...38
CAN COMMUNICATION : System Description ......38
COOLING FAN CONTROL .................................... ...38
COOLING FAN CONTROL : System Diagram .......38
COOLING FAN CONTROL : System Description ...38
EVAPORATIVE EMISSION SYSTEM .................... ...40
EVAPORATIVE EMISSION SYSTEM : System
Diagram ............................................................... ...
40
EVAPORATIVE EMISSION SYSTEM : System
Description ........................................................... ...
40
INTAKE VALVE TIMING CONTROL ..................... ...41
INTAKE VALVE TIMING CONTROL : System Di-
agram .................................................................. ...
41
INTAKE VALVE TIMING CONTROL : System De-
scription ............................................................... ...
41
EXHAUST VALVE TIMING CONTROL ................. ...42
EXHAUST VALVE TIMING CONTROL : System
Diagram ............................................................... ...
42
EXHAUST VALVE TIMING CONTROL : System
Description ........................................................... ...
42
ENGINE PROTECTION CONTROL AT LOW EN-
GINE OIL PRESSURE ..............................................
43
ENGINE PROTECTION CONTROL AT LOW EN-
GINE OIL PRESSURE : S ystem Diagram ..............
43
ENGINE PROTECTION CONTROL AT LOW EN-
GINE OIL PRESSURE : S ystem Description .........
43
FUEL FILLER CAP WARNING SYSTEM .............. ...44
FUEL FILLER CAP WARNING SYSTEM :
System Diagram ....................................................
44
FUEL FILLER CAP WARNING SYSTEM : System
Description ........................................................... ...
44
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ...45
AUTOMATIC SPEED CONTROL DEVICE (AS-
CD) : System Diagram ............................................
45
AUTOMATIC SPEED CONTROL DEVICE (AS-
CD) : System Description .......................................
45
OPERATION ......................................................47
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ...47
AUTOMATIC SPEED CONTROL DEVICE (AS-
CD) : Switch Name and Function ...........................
47
ON BOARD DIAGNOSTIC (OBD) SYSTEM .....49
Diagnosis Description .......................................... ...49
GST (Generic Scan Tool) .......................................49
DIAGNOSIS SYSTEM (ECM) ............................50
DIAGNOSIS DESCRIPTION .................................. ...50
DIAGNOSIS DESCRIPTION : 1st Trip Detection
Logic and Two Trip Detection Logic ........................
50
DIAGNOSIS DESCRIPTION : DTC and Freeze
Frame Data .......................................................... ...
50
DIAGNOSIS DESCRIPTION : Counter System ......51
DIAGNOSIS DESCRIPTION : Driving Pattern ..... ...54
DIAGNOSIS DESCRIPTION : System Readiness
Test (SRT) Code .................................................. ...
55
DIAGNOSIS DESCRIPTION : Permanent Diag-
nostic Trouble Code (Permanent DTC) ..................
56
DIAGNOSIS DESCRIPTION : Malfunction Indica-
tor Lamp (MIL) ..................................................... ...
57
On Board Diagnosis Function .................................57
CONSULT Function ................................................60
ECU DIAGNOSIS INFORMATION .............71
ECM ...................................................................71
Reference Value .................................................. ...71
Fail Safe .................................................................83
DTC Inspection Priority Chart ...............................85
DTC Index ..............................................................87
Test Value and Test Limit .......................................90
WIRING DIAGRAM ....................................99
ENGINE CONTROL SYSTEM ........................ ...99
Wiring Diagram .................................................... ...99
BASIC INSPECTION .................................120
DIAGNOSIS AND REPAIR WORKFLOW ...... ..120
Work Flow ............................................................ .120
Diagnostic Work Sheet .........................................123
ADDITIONAL SERVICE WHEN REPLACING
ECM ..................................................................
125
Description ........................................................... .125
Work Procedure ....................................................125
VIN REGISTRATION ........................................127
Description ........................................................... .127
Work Procedure ....................................................127
ACCELERATOR PEDAL RELEASED POSI-
TION LEARNING ............................................ ..
128
Description ........................................................... .128
Work Procedure ....................................................128
THROTTLE VALVE CLOSED POSITION
LEARNING .......................................................
129
Description ........................................................... .129
Work Procedure ....................................................129
IDLE AIR VOLUME LEARNING .......................130
Description ........................................................... .130
Work Procedure ....................................................130
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1132 of 3641
EC-5
C
DE
F
G H
I
J
K L
M
EC A
N
O P
P0444, P0445 EVAP CANISTER PURGE
VOLUME CONTROL SOLENOID VALVE ..... ..
300
DTC Logic ........................................................... ..300
Diagnosis Procedure .............................................300
Component Inspection ..........................................301
P0447 EVAP CANISTER VENT CONTROL
VALVE ..............................................................
303
DTC Logic ........................................................... ..303
Diagnosis Procedure .............................................303
Component Inspection ..........................................304
P0448 EVAP CANISTER VENT CONTROL
VALVE ..............................................................
307
DTC Logic ........................................................... ..307
Diagnosis Procedure .............................................307
Component Inspection ..........................................309
P0451 EVAP CONTROL SYSTEM PRES-
SURE SENSOR ................................................
311
DTC Logic ........................................................... ..311
Diagnosis Procedure .............................................312
Component Inspection ..........................................313
P0452 EVAP CONTROL SYSTEM PRES-
SURE SENSOR ................................................
315
DTC Logic ........................................................... ..315
Diagnosis Procedure .............................................315
Component Inspection ..........................................317
P0453 EVAP CONTROL SYSTEM PRES-
SURE SENSOR ................................................
318
DTC Logic ........................................................... ..318
Diagnosis Procedure .............................................318
Component Inspection ..........................................321
P0456 EVAP CONTROL SYSTEM ..................322
DTC Logic ........................................................... ..322
Diagnosis Procedure .............................................323
Component Inspection ..........................................327
P0460 FUEL LEVEL SENSOR ........................328
DTC Logic ........................................................... ..328
Diagnosis Procedure .............................................328
P0461 FUEL LEVEL SENSOR ........................329
DTC Logic ........................................................... ..329
Component Function Check ..................................329
Diagnosis Procedure .............................................330
P0462, P0463 FUEL LEVEL SENSOR ............331
DTC Logic ........................................................... ..331
Diagnosis Procedure .............................................331
P0500 VSS .......................................................332
Description .......................................................... ..332
DTC Logic .............................................................332
Component Function Check ..................................333
Diagnosis Procedure .............................................333
P0506 ISC SYSTEM .........................................334
Description ........................................................... ..334
DTC Logic ..............................................................334
Diagnosis Procedure .............................................334
P0507 ISC SYSTEM ........................................335
Description .............................................................335
DTC Logic ..............................................................335
Diagnosis Procedure .............................................335
P050A, P050B, P050E COLD START CON-
TROL ...............................................................
337
Description .............................................................337
DTC Logic ..............................................................337
Diagnosis Procedure .............................................338
P0520 EOP SENSOR ......................................339
DTC Logic ..............................................................339
Diagnosis Procedure .............................................339
Component Inspection ...........................................340
P0524 ENGINE OIL PRESSURE ....................341
DTC Logic ..............................................................341
Diagnosis Procedure .............................................342
Component Inspection ...........................................343
P059F ACTIVE GRILLE SHUTTER ................344
DTC Logic ..............................................................344
Diagnosis Procedure .............................................344
Component Inspection (Active Grille Shutter) .......347
Component Inspection (Active Grille Shutter Re-
lay) ....................................................................... ..
347
P0603 ECM .....................................................349
DTC Logic ..............................................................349
Diagnosis Procedure .............................................349
P0604 ECM .....................................................350
DTC Logic ..............................................................350
Diagnosis Procedure .............................................350
P0605 ECM .....................................................351
DTC Logic ..............................................................351
Diagnosis Procedure .............................................351
P0606 ECM .....................................................352
DTC Logic ..............................................................352
Diagnosis Procedure .............................................352
P0607 ECM .....................................................353
DTC Logic ..............................................................353
Diagnosis Procedure .............................................353
P060A ECM .....................................................354
DTC Logic ..............................................................354
Diagnosis Procedure .............................................354
P060B ECM .....................................................355
DTC Logic ..............................................................355
Diagnosis Procedure .............................................355
P0643 SENSOR POWER SUPPLY ................356
DTC Logic ..............................................................356
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1134 of 3641
EC-7
C
DE
F
G H
I
J
K L
M
EC A
N
O P
DTC Logic ...........................................................
..
416
Diagnosis Procedure .............................................416
Component Inspection ..........................................418
P2135 TP SENSOR ..........................................419
DTC Logic ........................................................... ..419
Diagnosis Procedure .............................................419
Component Inspection ..........................................420
P2138 APP SENSOR .......................................422
DTC Logic .............................................................422
Diagnosis Procedure .............................................422
Component Inspection ..........................................424
P219A AIR FUEL RATIO .................................426
DTC Logic ........................................................... ..426
Diagnosis Procedure .............................................427
P219C, P219D, P219E, P219F AIR FUEL RA-
TIO ....................................................................
431
DTC Logic ........................................................... ..431
Diagnosis Procedure .............................................433
ASCD BRAKE SWITCH ...................................437
Component Function Check ................................ ..437
Diagnosis Procedure .............................................437
Component Inspection (ASCD Brake Switch) .......438
CLUTCH PEDAL POSITION SWITCH .............439
Component Function Check ................................ ..439
Diagnosis Procedure .............................................439
Component Inspection (Clutch Pedal Position
Switch) ..................................................................
440
COOLING FAN .................................................441
Component Function Check ................................ ..441
Diagnosis Procedure .............................................441
Component Inspection (Cooling Fan Motor) .........443
Component Inspection (Cooling Fan Relay) .........443
ELECTRICAL LOAD SIGNAL .........................444
Description .......................................................... ..444
Component Function Check ..................................444
Diagnosis Procedure .............................................444
FUEL INJECTOR .............................................446
Component Function Check ................................ ..446
Diagnosis Procedure .............................................446
Component Inspection ..........................................447
FUEL PUMP .....................................................448
Component Function Check ................................ ..448
Diagnosis Procedure .............................................448
Component Inspection ..........................................450
IGNITION SIGNAL ...........................................451
Component Function Check ................................ ..451
Diagnosis Procedure .............................................451
Component Inspection (Ignition Coil with Power
Transistor) ........................................................... ..
454
Component Inspection (Condenser) ......................455
MALFUNCTION INDICATOR LAMP ..............456
Component Function Check ..................................456
Diagnosis Procedure .............................................456
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) ....................................................
457
Component Function Check ..................................457
Diagnosis Procedure .............................................457
Component Inspection (Refueling EVAP vapor cut
valve) ................................................................... ..
459
Component Inspection (Drain filter) .......................461
REFRIGERANT PRESSURE SENSOR ..........462
Component Function Check ..................................462
Diagnosis Procedure .............................................462
SYMPTOM DIAGNOSIS ............................464
ENGINE CONTROL SYSTEM SYMPTOMS ...464
Symptom Table ................................................... ..464
NORMAL OPERATING CONDITION .............470
Description .............................................................470
PERIODIC MAINTENANCE ......................471
IDLE SPEED .... ...............................................471
Inspection ............................................................ ..471
IGNITION TIMING ...........................................472
Inspection ..............................................................472
EVAPORATIVE EMISSION SYSTEM .............473
Inspection ..............................................................473
EVAP LEAK CHECK ......................................474
Inspection ..............................................................474
POSITIVE CRANKCASE VENTILATION .......476
Inspection ..............................................................476
REMOVAL AND INSTALLATION .............477
ECM .................................................................477
Exploded View ..................................................... ..477
Removal and Installation .......................................477
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... .......................................... .
478
SERVICE DATA AND SPECIFICATIONS
(SDS) ...............................................................
478
Idle Speed ........................................................... ..478
Ignition Timing .......................................................478
Calculated Load Value ..........................................478
Mass Air Flow Sensor ............................................478
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1136 of 3641
![NISSAN NOTE 2016 Service Manual PDF PRECAUTIONSEC-9
< PRECAUTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
General PrecautionsINFOID:0000000012431266
•
Always use a 12 volt battery as power source.
• Do not attempt to disconnect ba](/img/5/57363/w960_57363-1135.png "NISSAN NOTE 2016 Service Manual PDF PRECAUTIONSEC-9
< PRECAUTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
General PrecautionsINFOID:0000000012431266
•
Always use a 12 volt battery as power source.
• Do not attempt to disconnect ba")
PRECAUTIONSEC-9
< PRECAUTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
General PrecautionsINFOID:0000000012431266
•
Always use a 12 volt battery as power source.
• Do not attempt to disconnect battery cables while engine is
running.
• Before connecting or disc onnecting the ECM harness con-
nector, turn ignition switch OFF and disconnect negative bat-
tery cable. Failure to do so may damage the ECM because
battery voltage is applied to ECM even if ignition switch is
turned OFF.
• Before removing parts, turn ig nition switch OFF and then dis-
connect battery ground cable.
• Do not disassemble ECM.
• If a battery cable is disconnected, the memory will return to
the ECM value.
The ECM will now start to self-c ontrol at its initial value. So,
engine operation can vary slight ly in this case. However, this
is not an indication of a malf unction. Do not replace parts
because of a slight variation.
• If the battery is disconnected, the following emission-related
diagnostic information will be lost within 24 hours.
- Diagnostic trouble codes
- 1st trip diagnostic trouble codes
- Freeze frame data
- 1st trip freeze frame data
- System readiness test (SRT) codes
- Test values
• When connecting or disconnecting pin connectors into or
from ECM, take care not to damage pin terminals (bend or
break).
Make sure that there are not any bends or breaks on ECM pin
terminal, when connecting pin connectors.
• Securely connect ECM harness connectors.
A poor connection can cause an extremely high (surge) volt-
age to develop in coil and cond enser, thus resulting in dam-
age to ICs.
• Keep engine control system harness at least 10 cm (4 in) away
from adjacent harness, to prevent engine control system mal-
functions due to receiving externa l noise, degraded operation
of ICs, etc.
• Keep engine control system parts and harness dry.
• Before replacing ECM, perform ECM Terminals and Reference
Value inspection and make sure ECM functions properly.
Refer to EC-71, "
Reference Value".
• Handle mass air flow sensor carefully to avoid damage.
• Do not clean mass air flow senso r with any type of detergent.
• Do not disassemble electric th rottle control actuator.
• Even a slight leak in the air intake system can cause serious
incidents.
• Do not shock or jar the camsh aft position sensor (PHASE),
crankshaft position sensor (POS).
SEF289H
PBIA9222J
PBIB0090E
MEF040D
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1142 of 3641
![NISSAN NOTE 2016 Service Manual PDF COMPONENT PARTSEC-15
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
1. Ignition coil No.4
(with power transistor) 2. Ignition coil No.3
(with power transistor) 3. Ignition coil No.2
(](/img/5/57363/w960_57363-1141.png "NISSAN NOTE 2016 Service Manual PDF COMPONENT PARTSEC-15
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
1. Ignition coil No.4
(with power transistor) 2. Ignition coil No.3
(with power transistor) 3. Ignition coil No.2
(")
COMPONENT PARTSEC-15
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
1. Ignition coil No.4
(with power transistor) 2. Ignition coil No.3
(with power transistor) 3. Ignition coil No.2
(with power transistor)
4. Ignition coil No.1 (with power transistor) 5. PCV valve
6. Intake valve timing control solenoid
valve
7. Engine oil pressure sensor 8. Engine oil temperature sensor 9. Knock sensor
10. Engine coolant temperature sensor 11. Camshaft position sensor 12. Exhaust valve timing control position
sensor
13. Exhaust valve timing control sole- noid valve 14. Fuel injector No.1 (Front)
15. Fuel injector No.1 (Rear)
16. Fuel injector No.2 (Front) 17. Fuel injector No.2 (Rear)18. Fuel injector No.3 (Front)
19. Fuel injector No.3 (Rear) 20. Fuel injector No.4 (Front)21. Fuel injector No.4 (Rear)
22. Crankshaft position sensor
A. Engine front right side B. Left view of the engineC. Engine rear right side
JSBIA0592ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1145 of 3641
![NISSAN NOTE 2016 Service Manual PDF EC-18
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
Accelerator Pedal Position Sensor
INFOID:0000000012431271
The accelerator pedal position sensor is installed on the upper end
of the accelerator pe](/img/5/57363/w960_57363-1144.png "NISSAN NOTE 2016 Service Manual PDF EC-18
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
Accelerator Pedal Position Sensor
INFOID:0000000012431271
The accelerator pedal position sensor is installed on the upper end
of the accelerator pe")
EC-18
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
Accelerator Pedal Position Sensor
INFOID:0000000012431271
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometer which transform the accelerator pedal
position into output voltage, and emit the voltage signals to the ECM.
The ECM judges the current opening angle of the accelerator pedal
from these signals and controls the throttle control motor based on
these signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The
ECM uses this signal for the engine operation such as fuel cut.
Engine oil pressure sensor EC-21, "Engine Oil Pressure Sensor"
Engine oil temperature sensorEC-21, "Engine Oil Temperature Sensor"
EVAP canister purge volume control solenoid valveEC-22, "EVAP Canister Purge Volume Control Solenoid Valve"
EVAP canister vent control valveEC-22, "EVAP Canister Vent Control Valve"
EVAP control system pressure sensorEC-22, "EVAP Control System Pressure Sensor"
Exhaust valve timing control position sensor EC-19, "Camshaft Position Sensor"
Exhaust valve timing control solenoid valveEC-23, "Exhaust Valve Timing Control Solenoid Valve"
Fuel injectorEC-23, "Fuel Injector"
Fuel pumpEC-23, "Fuel Pump"
Heated oxygen sensor 2EC-24, "Heated Oxygen Sensor 2"
Heated oxygen sensor 2 heaterEC-24, "Heated Oxygen Sensor 2 Heater"
Ignition coil (with power transistor)EC-24, "Ignition Coil With Power Transistor"
Intake air temperature sensorEC-24, "Intake Air Temperature Sensor"
Camshaft position sensorEC-19, "Camshaft Position Sensor"
Intake valve timing control solenoid valveEC-25, "Intake Valve Timing Control Solenoid Valve"
Knock sensorEC-25, "Knock Sensor"
Mass air flow sensorEC-26, "Mass Air Flow Sensor"
PCV valveEC-28, "Positive Crankcase Ventilation"
Refrigerant pressure sensorEC-27, "Refrigerant Pressure Sensor"
Stop lamp switchEC-27, "Stop Lamp Switch & ASCD Brake Switch"
Throttle control motorEC-27, "Throttle Control Motor"
Throttle control motor relay EC-27, "Throttle Control Motor Relay"
Throttle position sensor EC-27, "Throttle Position Sensor"
ASCD steering switchEC-27, "ASCD Steering Switch"
ASCD brake switchEC-27, "Stop Lamp Switch & ASCD Brake Switch"
Clutch pedal position switchEC-20, "Clutch Pedal Position Switch"
Active grille shutterEXT-10, "ACTIVE GRILLE SHUTTER SYSTEM : Active grille shutter"
Component Reference
PBIB1741E
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1148 of 3641
![NISSAN NOTE 2016 Service Manual PDF COMPONENT PARTSEC-21
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Electric Throttle Control ActuatorINFOID:0000000012431279
Electric throttle control actuator consists of throttle c](/img/5/57363/w960_57363-1147.png "NISSAN NOTE 2016 Service Manual PDF COMPONENT PARTSEC-21
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Electric Throttle Control ActuatorINFOID:0000000012431279
Electric throttle control actuator consists of throttle c")
COMPONENT PARTSEC-21
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Electric Throttle Control ActuatorINFOID:0000000012431279
Electric throttle control actuator consists of throttle control mo
tor, throttle position sensor, etc.
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feed-
back to the ECM to control the throttle valve in response to driving conditions via the throttle control motor.
Engine Coolant Temperature SensorINFOID:0000000012431280
The engine coolant temperature sensor is used to detect the engine
coolant temperature. The sensor modifies a voltage signal from the
ECM. The modified signal returns to the ECM as the engine coolant
temperature input. The sensor uses a thermistor which is sensitive to
the change in temperature. The electrical resistance of the ther-
mistor decreases as temperature increases.
*: These data are reference values and are measured between ECM terminals.
Engine Oil Pressure SensorINFOID:0000000012431281
The engine oil pressure (EOP) sensor is detects engine oil pressure
and transmits a voltage signal to the ECM.
Engine Oil Temperature SensorINFOID:0000000012431282
The engine oil temperature sensor is used to detect the engine oil
temperature. The sensor modifies a voltage signal from the ECM.
The modified signal returns to the ECM as the engine oil tempera-
ture input. The sensor uses a thermistor which is sensitive to the
change in temperature. The electrical resistance of the thermistor
decreases as temperature increases.
SEF594K
Engine coolant temperature [ °C ( °F)] Voltage* (V) Resistance (k Ω)
–10 (14) 4.47.0 - 11.4
20 (68) 3.52.10 - 2.90
50 (122) 2.20.68 - 1.00
90 (194) 0.90.236 - 0.260
SEF012P
JSBIA0292ZZ
SEF594K
Revision: August 2015 2016 Versa Note
cardiagn.com