wheel NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual PATROL 1998 Y61 / 5.G NISSAN NISSAN https://www.carmanualsonline.info/img/5/620/w960_620-0.png NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual

Page 1 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual FRONT AXLE &
FRONT SUSPENSION
SECTION
FA
CONTENTS
PRECAUTIONS AND PREPARATION............................1
Precautions ..................................................................1
Special Servi

Page 2 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual Precautions
+When installing rubber parts, ®nal tightening must be car-
ried out under unladen condition* with tires on ground.
* Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand to

Page 4 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual NVH Troubleshooting Chart
Use the chart below to help you ®nd the cause of the symptom. If necessary, repair or replace these parts.
Reference pageFA-4
FA-25
Ð
Ð
Ð
FA-24
FA-8
FA-25
FA-5
FA-8
Ð
Ð

Page 6 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual Front Axle and Front Suspension Parts
Check front axle and front suspension parts for excessive play,
cracks, wear and other damage.
+Shake each front wheel to check for excessive play.
+Make sure tha

Page 7 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual PRELOAD ADJUSTMENT
Adjust wheel bearing preload after wheel bearing has been
replaced or front axle has been reassembled.
Adjust wheel bearing preload as follows:
1. Before adjustment, thoroughly clea

Page 8 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual 7. Turn wheel hub several times in both directions.
8. Retighten wheel bearing lock nut with Tool.
:3-5Nzm (0.3 - 0.5 kg-m, 26 - 43 in-lb)
9. Again turn wheel hub several times in both directions.
10.

Page 9 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual 19. Pack drive ¯ange groove with grease, apply grease to O-ring
and mating surface of drive ¯ange, and install ¯ange.
20. Place snap ring in drive shaft groove. Choose snap ring so that
the gap bet

Page 10 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual TOE-IN
Measure toe-in using the following procedure.
WARNING:
+Always perform the following procedure on a ¯at surface.
+Make sure that no person is in front of the vehicle before
pushing it.
1. Boun

Page 12 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual Removal
1. Set knob of manual-lock free-running hub to the ``FREE posi-
tion.
2. Loosen bolts and remove free-running hub assembly.
3. Remove snap ring and take off drive clutch.
4. Take out bushing

Page 13 of 29

NISSAN PATROL 1998 Y61 / 5.G Front Suspension Workshop Manual Installation
Install free-running hub in the reverse order of removal.
Apply multi-purpose grease to bushing and drive clutch
before installing on wheel hub and axle shaft, respectively.
+Install driv
Page:   1-10 11-20 next >