warning NISSAN TEANA 2003 Owner's Guide

INTELLIGENT KEY SYSTEM
BL-111
C
D
E
F
G
H
J
K
L
MA
B
BL

5. CHECK DOOR REQUEST SWITCH CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M31 terminals 5 (driver door), 25 (passenger
door), and 29 (trunk) and door request switch connector D25 (driver door), D43 (passenger door) terminal
3, T2 (trunk) terminal 2.
3. Check continuity between door request switch connector D25
(driver door), D43 (passenger door), T2 (trunk) terminals 3, 2
and ground.
OK or NG
OK >> Replace Intelligent Key unit.
NG >> Repair or replace harness between Intelligent Key unit and door request switch.
Check Intelligent Key Warning BuzzerBIS000XK
1. CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1. Turn ignition knob LOCK position.
2. Disconnect Intelligent Key warning buzzer connector.
3. Check voltage between Intelligent Key warning buzzer connector D22 (driver side), B222 (trunk room) ter-
minal 1 (Y/R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace Intelligent Key warning buzzer power
supply circuit.
2. CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M31 terminal 4, 23 and Intelligent Key warning
buzzer connector D22 (driver side), B222 (trunk room) terminal 2.
3. Check continuity between Intelligent Key warning buzzer con-
nector D22 (driver side), B222 (trunk room) terminal 2 and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between Intelligent Key warning buzzer and Intelligent Key unit.Driver 5 (B/W) - 3 (B/W) : Continuity should exist.
Passenger 25 (P/L) - 3 (P/L) : Continuity should exist.
Trunk 29 (G/O) - 2 (G/O) : Continuity should exist.
2 (G/O) - Ground : Continuity should not exist.
3 (B/W, P/L) - Ground : Continuity should not exist.
PIIB0957E
1 (Y/R) - Ground : Battery voltage
PIIA6748E
Driver side:
4 (SB) - 2 (SB) : Continuity should exist.
Trunk room:
4 (SB) - 2 (LG/B) : Continuity should exist.
2 (SB) - Ground : Continuity should not exist.
PIIB8798E

BL-112
INTELLIGENT KEY SYSTEM

3. CHECK INTELLIGENT KEY WARNING BUZZER OPERATION
Connect battery power supply to Intelligent Key warning buzzer connector D22 (driver side), B222 (trunk
room) terminals 1 and 2, and check the operation.
OK or NG
OK >> Intelligent Key warning buzzer is OK.
NG >> Replace Intelligent Key warning buzzer
Check Outside Key AntennaBIS000XL
1. CHECK OUTSIDE KEY ANTENNA POWER SUPPLY-1
Push each door request switch, and use an oscilloscope to check voltage waveform of harness between Intel-
ligent Key unit connector M31 terminals 17 (rear bumper), 19 (driver door), and 37 (passenger door) and
ground.
OK or NG
OK >> Outside key antenna is OK.
NG >> GO TO 2.1 (BAT+) - 2 (BAT-) : the buzzer sounds
PIIA6750E
Push each door request switch.
Rear bumper:
17 (W/R) - Ground
Driver:
19 (P) - Ground
Passenger:
37 (GR) - Ground
MIIB0375E
SIIA1910J

TRUNK LID
BL-133
C
D
E
F
G
H
J
K
L
MA
B
BL

3. Remove trunk lid stay.
WARNING:
Body injury may occur if no supporting rod is holding the
trunk lid open when removing the damper stay.
4. Remove the trunk lid hinge mounting bolts, and remove the
trunk lid assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

After installing, apply touch-up paint (the body color) onto the head of the hinge mounting bolts.

After installing, check the trunk lid adjustment. Refer to BL-131, "Fitting Adjustment" .
Trunk Lid Stay Removal and InstallationBIS000Y2
REMOVAL
1. Insert flat-bladed screwdriver into the gap and remove holder.
2. Remove trunk lid stay on the trunk lid.
3. Remove the stud bolts, and trunk lid stay.
WARNING:
Body injury may occur if no supporting rod is holding the trunk
lid open when removing the damper stay.
INSTALLATION
1. Install in the reverse order of removal.
2. After installing, check the operation.
PIIB0290E
SIIA1561E
PIIB0290E

PRECAUTIONS
BR-3
C
D
E
G
H
I
J
K
L
MA
B
BR

PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000BB
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000BC

Clean dust on front brake and rear brake with a vacuum dust collector. Do not blow with compressed air.

Recommended fluid is brake fluid “DOT 3 or DOT 4”. Refer to MA-14, "Fluids and Lubricants" .

Do not reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is splashed
on painted surfaces of body, immediately wipe it off and them wash it away with water immediately.

To clean or wash all parts of master cylinder, disc brake caliper, use clean brake fluid.

Do not use mineral oils such as gasoline or kerosene. They will ruin rubber parts of the hydraulic system.

Use a flare nut torque wrench when installing brake tube.

When installing brake tube, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery cables.

Burnish the brake contact surfaces after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low
mileage. Refer to BR-32, "
BRAKE BURNISHING PROCE-
DURE" (Front disc brake), BR-39, "BRAKE BURNISHING
PROCEDURE" (Rear disc brake).
WARNING:

Clean brake pads and shoes with a waste cloth, then wipe with a dust collector.
SBR820BA

BRAKE FLUID
BR-9
C
D
E
G
H
I
J
K
L
MA
B
BR

BRAKE FLUIDPFP:KN100
Checking Brake Fluid LevelBFS000BI

Make sure that a brake fluid level in reservoir tank is within the
standard (between MAX and MIN lines).

Visually check around reservoir tank for fluid leakage.

If fluid level is excessively low, check brake system for leakage.

Release parking brake pedal and see if brake warning lamp
goes off. If not, check brake system for fluid leakage.
Drain and RefillBFS000BJ
CAUTION:

Refill with new brake fluid “DOT 3 or DOT 4”.

Do not reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted surfaces of the body, immediately wipe off them and wash it away with water
immediately.

Before working, turn ignition switch OFF and disconnect electrical connector of ABS actuator and
electric unit (control unit) or battery cables.
1. Connect a vinyl tube to bleed valve.
2. Depress brake pedal, loosen bleed valve, and gradually remove
brake fluid.
3. Clean inside of reservoir tank, and refill with new brake fluid.
4. Rest foot on brake pedal. Loosen bleed valve. Slowly depress
brake pedal until it stops. Tighten bleed valve. Release brake
pedal. Repeat this process a few time, them pause to and new
brake fluid to master cylinder. Continue until new brake fluid
flows out.
5. Bleed air. Refer to BR-10, "
Bleeding Brake System" .
SFIA2632E
BRA0007D
PFIA0403J

BR-26
FRONT DISC BRAKE

FRONT DISC BRAKEPFP:41000
On-Board InspectionBFS000BX
PAD WEAR INSPECTION

Check pad thickness from the inspection hole on cylinder body.
Check use a scale for inspection necessary.
ComponentsBFS000BY
WARNING:
Clean dust on caliper and brake pads with a vacuum dust collector to minimize the hazard of airborne
particles or other materials.
CAUTION:

While removing cylinder body, never depress brake pedal because piston will pop out. Standard thickness : 11.0 mm (0.433 in)
Repair limit thickness : 2.0 mm (0.079 in)
BRA0010D
1. Union bolt 2. Brake hose 3. Copper washer
4. Cap 5. Bleed valve 6. Sliding pin bolt
7. Cylinder body 8. Piston seal 9. Piston
10. Piston boot 11. Inner shim cover 12. Inner shim
13. Pad wear sensor
(Only for inner pad RH)14. Inner pad 15. Pad retainer
16. Outer pad 17. Outer shim 18. Sliding pin
19. Sliding pin boot 20. Bushing 21. Torque member
22. Torque member mounting bolt
Refer to GI-10, "
Components" and the followings for the symbols in the figure.
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
3: Apply polyglycol ether based lubricant.
: Apply brake fluid.
PFIA0837E

BR-34
REAR DISC BRAKE

WARNING:
Clean dust on caliper and brake pads with a vacuum dust collector to minimize the hazard of air borne
particles or other materials.
CAUTION:

While removing cylinder body, do never depress brake pedal because piston will pop out.

It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang cylinder body with wire so as not to stretch
brake hose.

Do not damage piston boot.

If any shim is subject to serious corrosion, replace it with a new one.

Always replace shims and shim covers as a set when replacing brake pads.

Keep rotor clean from brake fluid.

Burnish brake contact surface after refinishing or replacing rotors, after replacing pads, or if a soft
pedal occurs at very low mileage. Refer to BR-39, "
BRAKE BURNISHING PROCEDURE" .
Removal and Installation of Brake PadBFS000C4
REMOVAL
1. Remove tyres from vehicle.
2. Remove upper sliding pin bolt.
3. Suspend cylinder body with wire, and remove pads, pad retainers and shims, and shim covers from
torque member.
INSTALLATION
1. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the bosh side of inner shim and outer
shin, install inner shim, inner shim cover to inner pad, and outer shim, outer shim cover to outer pad.
2. Install pad retainers and pads to torque member.
3. Press in piston until pads can be installed, and then install cylin-
der body to torque member.
NOTE:
Using a disc brake piston tool (commercial service tool) to easily
press piston in.
CAUTION:
When replacing pads with new ones, press in piston until
pads can be installed. In this case, carefully monitor brake
fluid level in reservoir tank because brake fluid will return to
master cylinder reservoir tank.
4. Install upper sliding pin bolt and tighten to the specified torque. Refer to BR-33, "
Components" .
5. Secure disc rotor with wheel nut. Depress brake pedal a few times until it gets a responsive touch.
6. Check rear disc brake for drag.
7. Install tyres to vehicle.
Refer to GI-10, "Components" and the followings for the symbols in the figure.
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
3: Apply polyglycol ether based lubricant.
: Apply brake fluid.
PFIA0273E

BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION BRC
A
B
BRC

BRAKE CONTROL SYSTEM
ABS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Brake System .................................. 3
Precautions for Brake Control .................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
SYSTEM DESCRIPTION ............................................ 5
System Diagram ....................................................... 5
Functions .................................................................. 5
ABS ....................................................................... 5
EBD ....................................................................... 6
Fail-Safe Function .................................................... 6
ABS, EBD SYSTEM .............................................. 6
Hydraulic Circuit Diagram ........................................ 6
CAN Communication ................................................ 7
SYSTEM DESCRIPTION ...................................... 7
TROUBLE DIAGNOSIS .............................................. 8
How to Perform Trouble Diagnosis For Quick and
Accurate Repair ....................................................... 8
INTRODUCTION ................................................... 8
DIAGNOSIS FLOW CHART ................................. 9
ASKING COMPLAINTS ...................................... 10
EXAMPLE OF DIAGNOSIS SHEET ................... 10
Component Parts Location ...................................... 11
Schematic .............................................................. 12
Wiring Diagram — ABS — ..................................... 13
Control Unit Input/Output Signal Specifications ..... 16
REFERENCE VALUE FROM CONSULT-II ......... 16
CONSULT-II Functions (ABS) ................................ 17
CONSULT-II MAIN FUNCTION ........................... 17
CONSULT-II SETTING PROCEDURE ................ 17
Self-Diagnosis ........................................................ 17
DESCRIPTION .................................................... 17
OPERATION PROCEDURE ............................... 17
ERASE MEMORY ............................................... 17
DISPLAY ITEM LIST ........................................... 18Data Monitor ........................................................... 19
OPERATION PROCEDURE ................................ 19
DISPLAY ITEM LIST ........................................... 19
Active Test .............................................................. 20
OPERATION PROCEDURE ................................ 20
TEST ITEM .......................................................... 21
For Fast and Accurate Diagnosis ........................... 22
PRECAUTIONS FOR DIAGNOSIS ..................... 22
Basic Inspection ..................................................... 22
BRAKE FLUID LEVEL, LEAKAGE AND BRAKE
PAD ..................................................................... 22
POWER SUPPLY CIRCUIT TERMINAL LOOSE-
NESS AND BATTERY ......................................... 22
INSPECTION OF ABS WARNING LAMP AND
BRAKE WARNING LAMP ................................... 23
TROUBLE DIAGNOSIS FOR SYSTEM .................... 24
Wheel Sensor System ............................................ 24
ABS Actuator and Electric Unit (Control Unit) 1 ..... 26
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground Circuit ..................................... 26
ABS Actuator Relay or ABS Motor Relay Power Sys-
tem .......................................................................... 28
CAN Communication System ................................. 29
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 30
Excessive ABS Function Operation Frequency ...... 30
Unexpected Pedal Action ....................................... 30
Longer Stopping Distance ...................................... 31
ABS Function Does Not Operate ............................ 31
Pedal Vibration and ABS Operation Sound Occurs ... 31
WHEEL SENSORS ................................................... 33
Removal and Installation ........................................ 33
COMPONENTS ................................................... 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 33
SENSOR ROTOR ..................................................... 34
Removal and Installation ........................................ 34
FRONT ................................................................ 34
REAR .................................................................. 34

BRC-2 ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 35
Removal and Installation ........................................ 35
COMPONENTS ................................................... 35
REMOVAL ........................................................... 36
INSTALLATION .................................................... 36
VDC/TCS/ABS
PRECAUTIONS ......................................................... 37
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 37
Precautions for Brake System ................................ 37
Precautions for Brake Control ................................ 37
PREPARATION ......................................................... 39
Special Service Tools ............................................. 39
ON-VEHICLE SERVICE ............................................ 40
Adjustment of Steering Angle Sensor Neutral Posi-
tion .......................................................................... 40
OPERATION PROCEDURE ................................ 40
SYSTEM DESCRIPTION .......................................... 41
System Diagram ..................................................... 41
Functions ................................................................ 41
VDC ..................................................................... 41
TCS ..................................................................... 41
ABS ..................................................................... 42
EBD ..................................................................... 42
Fail-Safe Function .................................................. 42
VDC/TCS SYSTEM ............................................. 42
ABS, EBD SYSTEM ............................................ 42
Hydraulic Circuit Diagram ....................................... 43
CAN Communication .............................................. 43
SYSTEM DESCRIPTION .................................... 43
TROUBLE DIAGNOSIS ............................................ 44
How to Perform Trouble Diagnosis Quick and Accu-
rate Repair .............................................................. 44
INTRODUCTION ................................................. 44
DIAGNOSIS FLOW CHART ................................ 45
ASKING COMPLAINTS ....................................... 46
EXAMPLE OF DIAGNOSIS SHEET .................... 46
Component Parts Location ..................................... 47
Schematic ............................................................... 48
Wiring Diagram — VDC — ..................................... 49
Control Unit Input/Output Signal Specifications ...... 55
REFERENCE VALUE FROM CONSULT-II ......... 55
CONSULT-II Functions ........................................... 57
CONSULT-II MAIN FUNCTION ........................... 57
CONSULT-II SETTING PROCEDURE ................ 57
Self-Diagnosis ........................................................ 58
DESCRIPTION .................................................... 58
OPERATION PROCEDURE ................................ 58
ERASE MEMORY ............................................... 58
DISPLAY ITEM LIST ........................................... 59
Data Monitor ........................................................... 61
OPERATION PROCEDURE ................................ 61
DISPLAY ITEM LIST ........................................... 61
Active Test .............................................................. 63
OPERATION PROCEDURE ................................ 63TEST ITEM .......................................................... 64
For Fast and Accurate Diagnosis ............................ 65
PRECAUTIONS FOR DIAGNOSIS ..................... 65
Basic Inspection ...................................................... 66
BRAKE FLUID LEVEL, LEAKAGE AND BRAKE
PAD ...................................................................... 66
POWER SUPPLY CIRCUIT TERMINAL LOOSE-
NESS AND BATTERY ......................................... 66
INSPECTION OF ABS WARNING LAMP, BRAKE
WARNING LAMP, VDC OFF INDICATOR LAMP,
AND SLIP INDICATOR LAMP ............................. 66
TROUBLE DIAGNOSIS FOR SYSTEM .................... 68
Wheel Sensor System ............................................ 68
Engine System ........................................................ 70
ABS Actuator and Electric Unit (Control Unit) 1 ...... 70
Steering Angle Sensor System ............................... 71
Yaw Rate/Side/Decel G Sensor System ................. 72
Pump Motor, Motor Relay System .......................... 74
Park/Neutral Position (PNP) Switch Circuit ............. 75
Solenoid and VDC Change-Over Valve, Actuator
Relay System .......................................................... 76
Stop Lamp Switch System ...................................... 77
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground System .................................... 78
Brake Fluid Level Switch System ............................ 80
CAN Communication System ................................. 81
Component Parts Inspection ................................... 81
VDC OFF SWITCH .............................................. 81
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 82
Excessive ABS Function Operation Frequently ...... 82
Unexpected Pedal Reaction ................................... 83
Longer Stopping Distance ....................................... 83
ABS Function Does Not Operate ............................ 84
Pedal Vibration and ABS Operation Sound Occurs ... 84
Vehicle Jerks During VDC/TCS/ABS Control .......... 85
WHEEL SENSORS ................................................... 86
Removal and Installation ......................................... 86
COMPONENTS ................................................... 86
REMOVAL ............................................................ 86
INSTALLATION .................................................... 86
SENSOR ROTOR ...................................................... 87
Removal and Installation ......................................... 87
FRONT ................................................................. 87
REAR ................................................................... 87
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 88
Removal and Installation ......................................... 88
COMPONENTS ................................................... 88
REMOVAL ............................................................ 89
INSTALLATION .................................................... 89
G SENSOR ................................................................ 90
Removal and Installation ......................................... 90
REMOVAL ............................................................ 90
INSTALLATION .................................................... 90
STEERING ANGLE SENSOR ................................... 91
Removal and Installation ......................................... 91
REMOVAL ............................................................ 91
INSTALLATION .................................................... 91

PRECAUTIONS
BRC-3
[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

[ABS]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000CK
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000CL

Recommended fluid is brake fluid “DOT 3” or “DOT 4”. Refer to MA-14, "RECOMMENDED FLUIDS AND
LUBRICANTS" .

Never reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas.

To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.

Never use mineral oils such as gasoline or kerosene. They will
ruin rubber parts of the hydraulic system.

Using a flare nut wrench when removing flare nuts, and use a
flare nut torque wrench when tighten brake tube flare nuts.

When installing brake tubes, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery negative terminal.
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with
a dust collector.
Precautions for Brake ControlBFS000CM

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal condition of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnostic servicing. Besides electrical system inspection, check brake booster operation, brake fluid
level, and fluid leaks.

If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.

If there is a radio, antenna, or antenna lead-in wire (including wiring) near control module, ABS function
may have a malfunction or error.

If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.
SBR820BA