Reverse NISSAN TEANA 2003 Repair Manual

A/C CONTROLLER
ATC-107
C
D
E
F
G
H
I
K
L
MA
B
AT C

A/C CONTROLLERPFP:27500
Removal and Installation of A/C and AV SwitchBJS000H4
REMOVAL
Refer to AV- 1 5 , "Removal and Installation of Audio Unit" (Integrated display system) or AV- 3 4 , "Removal and
Installation of Audio Unit" (Integrated color display system).
INSTALLATION
Installation is basically the reverse order of removal.

ATC-108
AUTO AMP

AUTO AMPPFP:27760
Removal and Installation of Unified Meter and A/C Amp.BJS000H6
REMOVAL
Refer to AV- 1 5 , "Removal and Installation of Audio Unit" (Integrated display system) or AV- 3 4 , "Removal and
Installation of Audio Unit" (Integrated color display system).
INSTALLATION
Installation is basically the reverse order of removal.

AMBIENT SENSOR
ATC-109
C
D
E
F
G
H
I
K
L
MA
B
AT C

AMBIENT SENSORPFP:27722
Removal and InstallationBJS000H7
REMOVAL
1. Remove engine undercover.
2. Disconnect ambient sensor connector, and then remove ambi-
ent sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA2180E

ATC-110
IN-VEHICLE SENSOR

IN-VEHICLE SENSORPFP:27720
Removal and InstallationBJS000H8
REMOVAL
1. Remove instrument driver lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting screw, and then remove in-vehicle sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3291E

SUNLOAD SENSOR
ATC-111
C
D
E
F
G
H
I
K
L
MA
B
AT C

SUNLOAD SENSORPFP:27721
Removal and InstallationBJS000H9
REMOVAL
1. Remove sunload sensor garnish.
2. Disconnect sunload sensor connector, and then remove sunload
sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3279E

ATC-112
INTAKE SENSOR

INTAKE SENSORPFP:27723
Removal and InstallationBJS000HA
REMOVAL
1. Remove low-pressure pipe 2 and high-pressure pipe 2. Refer to ATC-140, "Removal and Installation of
Low-pressure Pipe 2 and High-pressure Pipe 2" .
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Slide evaporator to passenger side, and then remove intake
sensor.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:

Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing
it.

Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sen-
sor can be located in the same position.

Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.

Insert piping securely until a click is heard.

After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.

When recharging refrigerant, check for leaks.
RJIA3281E

BLOWER UNIT
ATC-113
C
D
E
F
G
H
I
K
L
MA
B
AT C

BLOWER UNITPFP:27200
Removal and InstallationBJS000HB
REMOVAL
1. Remove instrument passenger lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting nuts, and then remove ECM with bracket
attached.
3. Disconnect fan control amp. connector and blower fan motor
connector.
4. Remove harness clip from blower unit.
5. Remove blower unit mounting bolts and screw, and then discon-
nect intake door motor connector.
CAUTION:
Move blower unit rightward, and remove locating pin (1
part) and joint. Then remove blower unit downward.
6. Remove blower unit.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
Make sure locating pin (1 part) and joint are securely inserted.
RJIA3292E
RJIA3293E

BLOWER MOTOR
ATC-115
C
D
E
F
G
H
I
K
L
MA
B
AT C

BLOWER MOTORPFP:27226
Removal and InstallationBJS000HD
REMOVAL
1. Remove instrument passenger lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Disconnect blower motor connector.
3. Remove mounting screws, and then remove blower motor and
motor cover.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3296E

ATC-116
FAN CONTROL AMPLIFIER

FAN CONTROL AMPLIFIERPFP:27761
Removal and InstallationBJS000HE
REMOVAL
1. Remove instrument passenger lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove harness clip.
3. Disconnect fan control amp. connector.
4. Remove mounting screws, and then remove fan control amp.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3297E

INTAKE DOOR MOTOR
ATC-117
C
D
E
F
G
H
I
K
L
MA
B
AT C

INTAKE DOOR MOTORPFP:27730
Removal and InstallationBJS000HF
REMOVAL
1. Remove blower unit. Refer to AT C - 11 3 , "BLOWER UNIT" .
2. Remove mounting screws, and then remove intake door motor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3298E