lock NISSAN TEANA 2008 Service Manual

DLK-220
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
HOOD LOCK
Exploded ViewINFOID:0000000003813423
Removal and InstallationINFOID:0000000003813424
REMOVAL
CAUTION:
Check wiring of hood lock control cable before removal.
1. Remove mounting bolts, and then remove hood lock assembly
(1).
NOTE:
Press the lever downward to avoid pin (A), then pull out hood
lock assembly upward.
2. Disconnect hood lock control cable (2) from hood lock assembly.
3. Disconnect bell crank assembly cable from hood lock assembly.
4. Remove air duct (inlet). Refer to EM-26, "
Removal and Installation".
5. Disconnect hood switch connector and remove hood lock assembly.
6. Remove bolts and remove bell crank assembly.
1. Hood lock 2. Hood switch 3. Bell crank assembly
4. Hood lock control cable 5. Hood lock opener
: Clip
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2381ZZ
JMKIA1914ZZ

HOOD LOCK
DLK-221
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
7. Disconnect hood lock control cable from instrument lower panel (LH).
8. Remove fender protector (LH). Refer to EXT-22, "
FENDER PROTECTOR : Removal and Installation".
9. Remove hood lock control cable clamp.
10. Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 Never bend cable too much. Keeping the radius 100 mm (3.937 in) or more.
 Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (A) properly.
 Check that hood lock control cable is properly engaged with hood lock.
 After installation, perform hood fitting adjustment. Refer to DLK-193, "
HOOD ASSEMBLY : Adjust-
ment".
 After installation, perform hood lock control inspection. Refer to DLK-221, "
Inspection".
InspectionINFOID:0000000003813425
NOTE:
If the hood lock cable is bent or deformed, replace it.
1. Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] by hood
weight.
2. While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
3. Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
4. Install so that static closing force of hood is 94 – 490 N (9.6 – 50.0 kg, 21.1 – 110 lb).
NOTE:
 Exert vertical force on right side and left side of hood lock.
 Do not simultaneously press both sides.
5. Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
JMKIA2398ZZ

DLK-222
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded ViewINFOID:0000000003813426
DOOR LOCK : Removal and InstallationINFOID:0000000003813427
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Remove front door glass. Refer to GW-17, "
Removal and Installation".
3. Remove front door module assembly. Refer to GW-20, "
Removal and Installation".
4. Remove outside handle and outside handle bracket. Refer to DLK-224, "
OUTSIDE HANDLE : Removal
and Installation".
5. Remove door lock assembly TORX bolts.
6. Disconnect door lock actuator connector, and then remove door lock assembly.
7. Remove key rod from door lock assembly.
INSTALLATION
Install in the reverse order of removal.
1. Outside handle 2. Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)3. Rear gasket
4. TORX bolt 5. Key rod (driver side) 6. Door lock assembly
7. Inside handle escutcheon 8. Inside handle 9. Seal
10. Outside handle bracket 11. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2386GB

FRONT DOOR LOCK
DLK-223
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
 When installing each rod, rotate rod holder until a click is felt.
 Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded ViewINFOID:0000000003817716
INSIDE HANDLE : Removal and InstallationINFOID:0000000003813429
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Disconnect inside handle cable.
3. Remove inside handle mounting screws, and then remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1. Outside handle 2. Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)3. Rear gasket
4. TORX bolt 5. Key rod (driver side) 6. Door lock assembly
7. Inside handle escutcheon 8. Inside handle 9. Seal
10. Outside handle bracket 11. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2386GB

DLK-224
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000003817718
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000003813431
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Remove front door glass. Refer to GW-17, "
Removal and Installation".
3. Remove front door module assembly. Refer to GW-20, "
Removal and Installation".
4. Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
1. Outside handle 2. Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)3. Rear gasket
4. TORX bolt 5. Key rod (driver side) 6. Door lock assembly
7. Inside handle escutcheon 8. Inside handle 9. Seal
10. Outside handle bracket 11. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2386GB

FRONT DOOR LOCK
DLK-225
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
5. Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never remove TORX bolt forcibly.
6. Reach in to separate key rod (2) connection [on the door key
cylinder assembly (1)] (driver side).
7. While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).
8. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9. Remove front gasket and rear gasket.
: TORX bolt
JMKIA2094ZZ
JMKIA0553ZZ
JMKIA0560ZZ
JMKIA0524ZZ

DLK-226
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 When installing each rod, rotate rod holder until a click is felt.
 Check door open/close, lock/unlock operation after installation.
JMKIA2303ZZ

REAR DOOR LOCK
DLK-227
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REAR DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded ViewINFOID:0000000003813432
DOOR LOCK : Removal and InstallationINFOID:0000000003813433
REMOVAL
1. Remove outside handle. Refer to DLK-229, "OUTSIDE HANDLE : Removal and Installation".
2. Remove rear door finisher. Refer to INT-36, "
Removal and Installation".
3. Remove sealing screen. Refer to GW-23, "
Removal and Installation".
4. Remove corner piece assembly. Refer to GW-23, "
Exploded View".
5. Fully close the rear door glass.
6. Reach in to separate outside handle cable connection on outside handle bracket.
7. Remove door lock TORX bolts.
8. Remove door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
1. Outside handle 2. Outside handle escutcheon 3. Rear gasket
4. TORX bolt 5. Door lock assembly 6. Inside handle escutcheon
7. Inside handle 8. Seal 9. Outside handle bracket
10. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2387GB

DLK-228
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
INSIDE HANDLE : Exploded View
INFOID:0000000003817719
INSIDE HANDLE : Removal and InstallationINFOID:0000000003813435
REMOVAL
1. Remove rear door finisher. Refer to INT-36, "Removal and Installation".
2. Disconnect inside handle cable.
3. Remove inside handle mounting screws, and then remove inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1. Outside handle 2. Outside handle escutcheon 3. Rear gasket
4. TORX bolt 5. Door lock assembly 6. Inside handle escutcheon
7. Inside handle 8. Seal 9. Outside handle bracket
10. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2387GB

REAR DOOR LOCK
DLK-229
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
OUTSIDE HANDLE : Exploded ViewINFOID:0000000003817720
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000003813437
REMOVAL
1. Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never remove TORX bolt forcibly.
1. Outside handle 2. Outside handle escutcheon 3. Rear gasket
4. TORX bolt 5. Door lock assembly 6. Inside handle escutcheon
7. Inside handle 8. Seal 9. Outside handle bracket
10. Front gasket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2387GB
: TORX bolt
JMKIA1467ZZ