bluetooth NISSAN TEANA 2008 Service Manual

AV-402
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM
 AV control unit is connected by CAN communication, and it receives data signal from ECM, combination
meter. It computes and displays fuel economy information value with the obtained information. Transmitting/
receiving of data signal is performed by BCM. Also, it transmits the required signal of vehicle setting and
receives the response signal.
 AV control unit is connected with display unit and serial communication, and it transmits the required signal
of display and display control and receives the response signal from display unit.
NOTE:
AV control unit can perform CONSULT-III self-operating function and on board self-diagnosis.
 CONSULT-III self diagnosis: Refer to AV-434, "
CONSULT-III Function (MULTI AV)".
 On board self diagnosis: Refer to AV-419, "
Diagnosis Description".
HANDS-FREE PHONE SYSTEM
 Hands-free communication can be operated by connecting using Bluetooth™ communication with cellular
phone.
 Operation is performed by display unit (touch panel), multifunction switch or steering switch, and operating
condition is indicated on display unit.
When a call is originated
Spoken voice sound output from the microphone (Mic. Signal) is input to NAVI control unit. NAVI control unit
outputs to cellular phone via TEL antenna with Bluetooth
™ communication as a TEL voice signal. Voice sound
is then heard at the other party.
When receiving a call
Voice sound is input to own cellular phone from the other party. The cellular phone outputs the voice signal to
TEL antenna by establishing Bluetooth
™ communication. The signal from TEL antenna is sent to front speaker
via NAVI control unit, AV control unit, and BOSE amp.
DVD ENTERTAINMENT SYSTEM
 DVD player is connected with AV control unit via AV communication, and controlled by AV control unit.
 DVD image signal is output from DVD player to display unit via AV control unit.
 DVD stereo (2ch) sound signal is output from DVD player to each speaker via AV control unit and BOSE
amp.
 DVD surround (5.1ch) sound signal is output from DVD player to each speaker via BOSE amp.
JSNIA1305GB

AV
MULTI AV SYSTEM
AV-405
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003765830
13. Camera control unit 14. TEL antenna 15. Rear squawker RH
16. Antenna amp. 17. GPS antenna 18. Rear door speaker RH
19. Front door speaker RH 20. Steering angle sensor 21. Steering switch
22. AV control unit 23. Auxiliary input jacks 24. Preset switch
25. DVD player 26. Multifunction switch 27. Display unit
28. Microphone
A. Trunk room upper LH B. Trunk room upper RH C. Trunk room side RH
D. Within rear pillar finisher RH E. Within rear pillar finisher RH F. Within rear parcel shelf finisher
G. Spiral cable part H. In center console I. In grove box
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
 AV control unit includes audio function and vehicle information function.
 It is connected to ECM and combination meter. via CAN communication to ob-
tain necessary information for the vehicle information function.
 It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
 Composite image signal (AUX and DVD images) is input from DVD player.
 Camera image signal is input from camera control unit.
 Composite image (DVD, AUX and camera images) signal is output to display
unit.
 Sound signal (DVD and AUX sounds) is input from the DVD player.
NAVI CONTROL UNIT Map data can be read from the Map DVD-ROM by installing Map DVD-ROM.
 The NAVI control unit sends map data to the AV control unit.
 The NAVI control unit includes the hands-free phone and navigation functions.
 The NAVI control unit transmits navigation and hands-free phone related im-
ages to AV control unit.
 It includes the TEL adapter and Bluetooth
™ function.
Map DVD-ROM A collection of map data.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
 RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing).
 Composite image (DVD, AUX and camera images) signal is input from AV con-
trol unit.
 Synchronize signal (HP, VP) is output to AV control unit.
 Touch panel function can be operated for each system by touching a display
directly.
BOSE AMP.Inputs sound signal from AV control unit and DVD player, and outputs sound sig-
nal to woofer and each speaker.
WOOFER Outputs sound signal from BOSE amp.
 Outputs low frequency sound.
FRONT SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
REAR SQUAWKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
CENTER SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).

AV-420
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
NOTE:
*: On-board self-diagnosis is not supported. Only CONSULT-III is supported.
STARTING PROCEDURE
1. Start the engine.
2. Turn the audio system OFF.
3. While pressing the “SETTING” button, turn the volume control
dial clockwise or counterclockwise for 40 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
 Shifting from current screen to previous screen is performed
by pressing “BACK” button.
Confirmation/
AdjustmentDisplay DiagnosisThe confirmations of the tint with the color spectrum bar display and
shading of color with the gradation bar display can be performed.
Vehicle SignalsDiagnosis of signals can be performed for vehicle speed, parking brake,
lights, ignition switch, and reverse.
Navigation/PhoneHandsfree Voice Mi-
crophone TestMicrophone speaker check can be performed.
Color Spectrum Bar A color tone can be checked by the color bar display.
Gradation Bar A light and shade can be checked by the gray scale display.
Touch Panel Touch panel response check can be performed.
Vehicle SignalsDiagnosis of signals can be performed for vehicle speed, parking brake,
lights, and reverse.
Confirm/Change
Bluetooth PasskeyThe passkey can be checked and changed.
Confirm/Change
Bluetooth Device
NameThe device name can be checked and changed.
Handsfree Sound
Quality SetNot available.
Speaker Test The connection of a speaker can be confirmed by test tone.
Climate Control
*Not used.
Error HistoryThe system malfunction and the frequency when occurred in the past are
displayed. When the malfunctioning item is selected, the time and place
that the selected malfunction last occurred are displayed.
Camera Cont.The signal connected to camera control unit can be checked and the
guiding line position that overlaps rear view camera image can be adjust-
ed.
Vehicle CAN Diagnosis The transmitting/receiving of CAN communication can be monitored.
AV COMM DiagnosisThe communication condition of each unit of Multi AV system can be
monitored.
Delete Unit Connection Log Erase the connection history of unit and error history.
Initialize Settings Initializes the AV control unit memory.Mode Description
JSNIA1290GB

AV-428
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Confirm/Change Bluetooth Passkey
 The passkey of Bluetooth can be confirmed and changed.
 The passkey can be changed by four to eight digits within the num-
ber of 0 to 9.
Confirm/Change Bluetooth Device Name
 The device name of Bluetooth can be confirmed and changed.
 The device name can be changed within the range of twenty digits
of alphabets and codes.
Speaker Test
Select “SPEAKER TEST” to display the Speaker Diagnosis screen.
Press “START and NEXT” to generate a test tone in a speaker.
Press “Start” to generate a test tone in the next speaker. Press “End”
to stop the test tones.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
Climate Control
On-board self-diagnosis is not supported. Only CONSULT-III is supported.
Refer to HAC-159, "
WITH INTELLIGENT AIR CONDITIONER SYSTEM : CONSULT-III Function" for details.
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-diagnosis start because of this situation.
The frequency of occurrence in error history is displayed in a count up manner. The actual count up method
differs depending on the error item.
Count up method A
LightsON Light switch ON.
—
OFF Light switch OFF.
ReverseON Selector lever in R position.
Changes in indication may be delayed. This is normal.
OFFSelector lever in any position other
than R. Diagnosis item Display Vehicle status Remarks
JSNIA0086GB
JSNIA0517GB
Tweeter : 3 kHz
Front door speaker : 300 Hz
Rear door speaker : 1 kHz
JSNIA0150GB

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-431
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
FL speaker OUT: openSound signal front speaker LH circuit is
open.Check sound signal front speaker LH cir-
cuit.
FL speaker OUT: shortSound signal front speaker LH circuit is
shorted between front speaker LH signal
(+) and front speaker LH signal (-).Check sound signal front speaker LH cir-
cuit.
FL speaker OUT: short to groundSound signal front speaker LH circuit to
ground is shorted.Check sound signal front speaker LH cir-
cuit.
FL speaker OUT: short to batterySound signal front speaker LH circuit to
battery is shorted.Check sound signal front speaker LH cir-
cuit.
FL tweeter OUT: openSound signal front squawker LH circuit is
open.Check sound signal front squawker LH cir-
cuit.
FL tweeter OUT: shortSound signal front squawker LH circuit is
shorted between front squawker LH signal
(+) and front squawker LH signal (-).Check sound signal front squawker LH cir-
cuit.
FL tweeter OUT: short to groundSound signal front squawker LH circuit to
ground is shorted.Check sound signal front squawker LH cir-
cuit.
FL tweeter OUT: short to batterySound signal front squawker LH circuit to
battery is shorted.Check sound signal front squawker LH cir-
cuit.
FR tweeter OUT: openSound signal front squawker RH circuit is
open.Check sound signal front squawker RH cir-
cuit.
FR tweeter OUT: shortSound signal front squawker RH circuit is
shorted between front squawker RH signal
(+) and front squawker RH signal (-).Check sound signal front squawker RH cir-
cuit.
FR tweeter OUT: short to groundSound signal front squawker RH circuit to
ground is shorted.Check sound signal front squawker RH cir-
cuit.
FR tweeter OUT: short to batterySound signal front squawker RH circuit to
battery is shorted.Check sound signal front squawker RH cir-
cuit.
GPS Antenna ErrorGPS antenna connection malfunction is de-
tected.Replace the GPS antenna.
DVD Navi Internal Error NAVI control unit malfunction is detected. Replace the NAVI control unit.
Bluetooth module ErrorTEL antenna connection malfunction is de-
tected.TEL antenna.
AV COMM CIRCUITRear control switch power supply and
ground circuits malfunction are detected.Rear control switch power supply and
ground circuits.
 AV COMM CIRCUIT
 Switches Connection ErrorWhen either one of the following items is
detected:
 multifunction switch power supply and
ground circuits are malfunctioning.
 AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.
 AV communication signal between AV
control unit and multifunction switch is
malfunctioning. Multifunction switch power supply and
ground circuits.
 AV communication circuits between AV
control unit and multifunction switch.
 AV COMM CIRCUIT
 DVD Navi Unit Connection ErrorNAVI control unit power supply and ground
circuits are malfunctioning.NAVI control unit power supply and ground
circuits.
 AV COMM CIRCUIT
 Amplifier Connection ErrorWhen either one of the following items is
detected:
 BOSE amp. power supply and ground
circuits are malfunctioning.
 AV communication signal between AV
control unit and BOSE amp is malfunc-
tioning.BOSE amp. power supply and ground cir-
cuits. Error item Description Possible malfunction factor/Action to take

AV-460
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
U12A1 NAVI CONTROL UNIT
U12A1 NAVI CONTROL UNIT
DescriptionINFOID:0000000003765869
Replace the NAVI control unit if this DTC is displayed. Refer to AV-649, "Removal and Installation".
DTC LogicINFOID:0000000003765870
DTC DETECTION LOGIC
Part name Description
NAVI CONTROL UNIT Map data can be read from the Map DVD-ROM by installing Map DVD-ROM.
 The NAVI control unit sends map data to the AV control unit.
 The NAVI control unit includes the hands-free phone and navigation functions.
 The NAVI control unit transmits navigation and hands-free phone related imag-
es to AV control unit.
 It includes the TEL adapter and Bluetooth
™ function.
Map DVD-ROM A collection of map data.
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U12A1NAVI INTERNAL ERR
[U12A1]NAVI control unit malfunction is detected. Replace the NAVI control unit.

AV-640
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom TableINFOID:0000000003765976
RELATED TO BASIC OPERATION
RELATED TO HANDS FREE PHONE
 Check that the cellular phone is corresponding type (Bluetooth™ correspond) when the hands free related
malfunction vehicle is in service before performing a diagnosis,.
 There is a case that malfunction occurs due to the version change of the phone type, etc. even though it is a
corresponding type. Therefore, confirm it by changing the cellular phone to another corresponding type
phone, and check that it operates normally. It is necessary to distinguish whether the cause is the vehicle or
cellular phone.
Simple check for Bluetooth™ communication
If cellular phone and NAVI control unit cannot be connected with Bluetooth™ communication, following proce-
dure allows the technician to judge which device has malfunction.
1. Turn on a cellular phone, not connecting Bluetooth
™ communication.
2. Start CONSULT-III, then start Windows
®.
3. Set CONSULT-III near a cellular phone.
4. When operated Bluetooth
™ registration by cellular phone, check
if CONSULT-III
* would be displayed on the device name.
(If other Bluetooth
™ device is located near cellular phone, a
name of the device would be displayed also.)
NOTE:
*:Displayed device name is “NISSAN- ”.
 If no device name is displayed, cellular phone is malfunction.
Repair the cellular phone first, then perform diagnosis.
 If CONSULT-III is displayed on device name, cellular phone is nor-
mal. Perform diagnosis as per the following table.
Symptoms Check items Possible malfunction location / Action to take
Multifunction switch and preset
switch operation does not work. All switches cannot be operated
 “MULTI AV” is displayed on system
selection screen when the CON-
SULT-III is started.Perform CONSULT-III self-diagnosis. Refer to AV- 4 3 4 ,
"CONSULT-III Function (MULTI AV)".
 All switches cannot be operated
 “MULTI AV” is not displayed on sys-
tem selection screen when the CON-
SULT-III is started.AV control unit power supply and ground circuit malfunc-
tion. Refer to AV- 4 6 4 , "
AV CONTROL UNIT : Diagnosis
Procedure".
Only specified switch cannot be operat-
ed.Multifunction switch or preset switch malfunction.
Replace multifunction switch or preset switch.
For multifunction switch, refer to AV- 6 5 9 , "
Removal and
Installation".
For preset switch, refer to AV- 6 6 0 , "
Removal and Instal-
lation".
Fuel economy display, vehicle set-
ting operation is abnormal.There is malfunction in the CONSULT-
III self-diagnosis result.Perform detected DTC diagnosis.
There is no malfunction in the self-diag-
nosis results.Ignition signal circuit malfunction.
Refer to AV- 4 6 4 , "
AV CONTROL UNIT : Diagnosis Pro-
cedure".
Guide sound is not heard.On the setting display select “system
sound (guide sound volume, etc.),” and
confirm that guide sound is ON.Voice guidance signal circuit malfunction.
JPNIA0441GB