wheel NISSAN TEANA 2008 Owner's Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 919 of 5121

BRAKE PIPINGBR-23
< ON-VEHICLE REPAIR >
C
DE
G H
I
J
K L
M A
B
BR
N
O P
REAR : Removal and InstallationINFOID:0000000003811192
REMOVAL
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with wate r if it gets on a painted surface.
1. Remove tires.
2. Drain brake fluid. Refer to BR-9, "
Draining".
3. Loosen the flare nut with a flare nut wrenc h and separate the brake tube from the hose.
CAUTION:
Never scratch the flare nut and the brake tube.
Never sharply bend, twist or strongly pull the brake hoses and tubes.
Cover the open end of brake tubes and hoses wh en disconnecting to prevent entrance of dirt.
4. Remove the union bolt and copper washers, and remove the brake hose from the brake caliper assembly.
5. Remove the lock plate and remove the brake hose from the vehicle.
INSTALLATION
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with wate r if it gets on a painted surface.
1. Assemble the union bolt and the copper washers to the brake hose. CAUTION:
Never reuse copper washer.
2. Install the brake hose L-pin by aligning it with the brake caliper assembly positioning hole, and tighten the union bolt (1) to the
specified torque.
3. Connect the hose to the brake tube, temporarily tighten the flare nut by hand until it does not rotate further, and fix the brake hose
to the bracket with the lock plate.
CAUTION:
Check that the brake hoses and tubes are not twisted and
bent.
4. Tighten the flare nut to the specified torque with a crowfoot and torque wrench.
CAUTION:
Never scratch the flare nut and the brake tube.
5. Refill with new brake fluid and perform the air bleeding. Refer to BR-10, "
Bleeding Brake System".
CAUTION:
Never reuse drained brake fluid.
REAR : InspectionINFOID:0000000003811193
INSPECTION AFTER INSTALLATION
1. Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no interfer-
ence with other components when steering the steering wheel; no looseness at connections.
2. Depress the brake pedal with a force of 785N (80
kg, 177 lb) and hold down the pedal for approximately 5
seconds with the engine running. Check for any fluid leakage.
CAUTION:
1. ABS actuator and electric unit (con- trol unit) 2. Front disc brake 3. Master cylinder assembly
4. Brake booster 5. Connector 6. Rear disc brake
A. Brake tube B. Brake hose : Flare nut
: Union bolt
JPFIA0012ZZ
Page 932 of 5121

BR-36
< ON-VEHICLE REPAIR >
FRONT DISC BRAKE
CAUTION:
Never depress the brake pedal. Brake fluid may splash while removing the brake hose.
1. Remove tires.
2. Fix the disc rotor using wheel nuts.
3. Drain brake fluid. Refer to BR-9, "
Draining".
CAUTION:
Never spill or splash brake fluid on the disc rotor.
4. Remove union bolt and copper washers, and then disconnect brake hose from caliper assembly. Refer to
BR-19, "
FRONT : Exploded View".
5. Remove torque member mounting bolts, and remove brake caliper assembly.
CAUTION:
Never drop brake pads and caliper assembly.
6. Remove disc rotor.
CAUTION:
Put matching marks on the wheel hub and bearing assembly and the disc rotor before removing
the disc rotor.
Never drop disc rotor.
INSTALLATION
WARNING:
Clean any dust from the brake caliper and brake pads with a vacuum dust collector. Never blow with
compressed air.
CAUTION:
Never depress the brake pedal. Brake fluid may splash while removing the brake hose.
1. Install disc rotor.
CAUTION:
Align the matching marks put during removal when reusing the disc rotor.
2. Install the brake caliper assembly to the vehicle and tighten the torque member mounting bolts to the
specified torque.
CAUTION:
Never spill or splash any grease and moisture on the brake caliper assembly mounting face,
threads, mounting bolts and washers. Wipe out any grease and moisture.
3. Install brake hose and copper washers to brake caliper assembly, and tighten union bolts to the specified
torque. Refer to BR-19, "
FRONT : Exploded View".
CAUTION:
Never reuse copper washer.
4. Refill with new brake fluid and perform the air bleeding. Refer to BR-10, "
Bleeding Brake System".
CAUTION:
Never reuse drained brake fluid.
Never spill or splash brake fluid on the disc rotor.
5. Check a drag of front disc brake. If any drag is found, refer to BR-38, "
BRAKE CALIPER ASSEMBLY :
Inspection".
BRAKE CALIPER ASSEMBLY : Disassembly and AssemblyINFOID:0000000003811209
DISASSEMBLY
NOTE:
Never remove the torque member and pad retainers when disassembling and assembling the cylinder body.
1. Remove the sliding pin bolts, and remove the cylinder body from the torque member.
CAUTION:
Never drop brake pads, shims, shim cover and pad retainers from torque member.
2. Remove brake pads, shims and shim cover. Refer to BR-33, "
BRAKE PAD : Exploded View".
3. Remove sliding pins and sliding pin boots from torque member.
4. Remove bushing from sliding pin.
Page 938 of 5121

BR-42
< ON-VEHICLE REPAIR >
REAR DISC BRAKE
Clean any dust from the brake caliper and brake pads with a vacuum dust collector. Never blow with
compressed air.
CAUTION:
Never depress the brake pedal. Brake fluid may splash while removing the brake hose.
1. Remove tires.
2. Fix the disc rotor using wheel nuts.
3. Drain brake fluid. Refer to BR-9, "
Draining".
CAUTION:
Never spill or splash brake fluid on the disc rotor.
4. Remove union bolt and copper washers then disconnect brake hose from caliper assembly.
5. Remove torque member mounting bolts, and remove brake caliper assembly.
CAUTION:
Never drop brake pads and caliper assembly.
6. Remove disc rotor.
CAUTION:
Put matching marks on the wheel hub and bearing assembly and the disc rotor before removing
the disc rotor.
Never drop disc rotor.
INSTALLATION
WARNING:
Clean any dust from the brake caliper and brake pads with a vacuum dust collector. Never blow with
compressed air.
CAUTION:
Never depress the brake pedal. Brake fluid may splash while removing the brake hose.
1. Install disc rotor.
CAUTION:
Align the matching marks put during removal when reusing the disc rotor.
2. Install the brake caliper assembly to the vehicle and tighten the torque member mounting bolts to the
specified torque.
CAUTION:
Never spill or splash any grease and moisture on the brake caliper assembly mounting face,
threads, mounting bolts, and washers. Wipe out any grease and moisture.
3. Install brake hose and copper washers to brake caliper assembly, and tighten union bolts to the specified
torque. Refer to BR-22, "
REAR : Exploded View".
CAUTION:
Never reuse copper washer.
4. Refill with new brake fluid and perform the air bleeding. Refer to BR-10, "
Bleeding Brake System".
CAUTION:
Never reuse drained brake fluid.
Never spill or splash brake fluid on the disc rotor.
5. Check that no drag feel is present for the rear disc brake. Refer to BR-44, "
BRAKE CALIPER ASSEMBLY
: Inspection".
BRAKE CALIPER ASSEMBLY : Disassembly and AssemblyINFOID:0000000003811216
DISASSEMBLY
NOTE:
Never remove the torque member and pad retainers when disassembling and assembling the cylinder body.
1. Remove the sliding pin bolts and remove the cylinder body from the torque member.
2. Remove brake pads and shims. Refer to BR-39, "
BRAKE PAD : Exploded View".
3. Remove sliding pin boots from torque member.
4. Remove bushing from sliding pin bolt.
Page 942 of 5121

BRC-1
BRAKES
C
DE
G H
I
J
K L
M
SECTION BRC
A
B
BRC
N
O P
CONTENTS
BRAKE CONTROL SYSTEM
ABS
BASIC INSPECTION ....... .............................
6
DIAGNOSIS AND REPAIR WORK FLOW .... .....6
Work Flow ........................................................... ......6
Diagnostic Work Sheet ..............................................8
FUNCTION DIAGNOSIS ...............................9
ABS ................................................................ .....9
System Diagram .................................................. ......9
System Description ...................................................9
Component Parts Location ......................................10
Component Description ...........................................10
EBD ....................................................................11
System Diagram .................................................. ....11
System Description .................................................11
Component Parts Location ......................................12
Component Description ...........................................12
DIAGNOSIS SYSTEM [ABS ACTUATOR
AND ELECTRIC UNIT (CONTROL UNIT)] ........
13
CONSULT-III Function ........................................ ....13
COMPONENT DIAGNOSIS .........................16
C1101, C1102, C1103, C1104 WHEEL SEN-
SOR ................................................................ ....
16
Description .......................................................... ....16
DTC Logic ...............................................................16
Diagnosis Procedure ...............................................16
Component Inspection ............................................18
C1105, C1106, C1107, C1108 WHEEL SEN-
SOR ....................................................................
19
Description .......................................................... ....19
DTC Logic ...............................................................19
Diagnosis Procedure ...............................................19
Component Inspection ............................................21
C1109 POWER AND GROUND SYSTEM ........22
Description ........................................................... ....22
DTC Logic ................................................................22
Diagnosis Procedure ...............................................22
C1110 ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT) ....................................
24
DTC Logic ................................................................24
Diagnosis Procedure ...............................................24
C1111 ABS MOTOR, MOTOR RELAY SYS-
TEM ...................................................................
25
Description ...............................................................25
DTC Logic ................................................................25
Diagnosis Procedure ...............................................25
Component Inspection .............................................26
C1115 WHEEL SENSOR ..................................27
Description ...............................................................27
DTC Logic ................................................................27
Diagnosis Procedure ...............................................27
Component Inspection .............................................29
C1116 STOP LAMP SWITCH ...........................30
Description ...............................................................30
DTC Logic ................................................................30
Diagnosis Procedure ...............................................30
Component Inspection .............................................30
C1120, C1122, C1124, C1126 IN ABS SOL .....32
Description ...............................................................32
DTC Logic ................................................................32
Diagnosis Procedure ...............................................32
Component Inspection .............................................33
C1121, C1123, C1125, C1127 OUT ABS SOL ...34
Description ........................................................... ....34
DTC Logic ................................................................34
Diagnosis Procedure ...............................................34
Component Inspection .............................................35
C1140 ACTUATOR RELAY SYSTEM ..............36
Page 943 of 5121

BRC-2
Description ..............................................................36
DTC Logic ...............................................................36
Diagnosis Procedure ..............................................36
Component Inspection ............................................37
U1000, U1002 CAN COMM CIRCUIT ...............38
Description ..............................................................38
DTC Logic ...............................................................38
Diagnosis Procedure ..............................................38
POWER SUPPLY AND GROUND CIRCUIT .....39
Description ..............................................................39
Diagnosis Procedure ..............................................39
ABS WARNING LAMP ......................................40
Description ..............................................................40
Component Function Check ...................................40
Diagnosis Procedure ..............................................40
BRAKE WARNING LAMP .................................41
Description ..............................................................41
Component Function Check ...................................41
Diagnosis Procedure ..............................................41
ECU DIAGNOSIS ........................................42
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) ..............................................
42
Reference Value .....................................................42
Wiring Diagram - BRAKE CONTROL SYSTEM - ...44
Fail-Safe .................................................................47
DTC No. Index ........................................................48
SYMPTOM DIAGNOSIS .............................49
EXCESSIVE ABS FUNCTION OPERATION
FREQUENCY .....................................................
49
Diagnosis Procedure ..............................................49
UNEXPECTED PEDAL REACTION ..................50
Diagnosis Procedure ..............................................50
THE BRAKING DISTANCE IS LONG ...............51
Diagnosis Procedure ..............................................51
ABS FUNCTION DOES NOT OPERATE ..........52
Diagnosis Procedure ..............................................52
PEDAL VIBRATION OR ABS OPERATION
SOUND OCCURS ..............................................
53
Diagnosis Procedure ..............................................53
NORMAL OPERATING CONDITION ................54
Description ..............................................................54
PRECAUTION .............................................55
PRECAUTIONS .................................................55
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
55
Precaution for Procedure without Cowl Top Cover ...55
Precaution for Brake System ..................................55
Precaution for Brake Control ...................................56
Precautions for Harness Repair ..............................56
ON-VEHICLE REPAIR ...............................57
WHEEL SENSOR ..............................................57
FRONT WHEEL SENSOR ........................................57
FRONT WHEEL SENSOR : Exploded View ...........57
FRONT WHEEL SENSOR : Removal and Instal-
lation .......................................................................
57
REAR WHEEL SENSOR ...........................................58
REAR WHEEL SENSOR : Exploded View .............58
REAR WHEEL SENSOR : Removal and Installa-
tion ..........................................................................
58
SENSOR ROTOR ..............................................59
FRONT SENSOR ROTOR ........................................59
FRONT SENSOR ROTOR : Exploded View ...........59
FRONT SENSOR ROTOR : Removal and Instal-
lation .......................................................................
59
REAR SENSOR ROTOR ...........................................59
REAR SENSOR ROTOR : Exploded View .............59
REAR SENSOR ROTOR : Removal and Installa-
tion ..........................................................................
59
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) ..............................................
60
Exploded View ........................................................60
Removal and Installation .........................................60
VDC/TCS/ABS
BASIC INSPECTION ..................................
62
DIAGNOSIS AND REPAIR WORK FLOW ........62
Work Flow ...............................................................62
Diagnostic Work Sheet ...........................................65
INSPECTION AND ADJUSTMENT ...................66
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ........................................................
66
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ................................
66
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .....
66
ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION ................................................
66
ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION : Description ........................
66
ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION : Special Repair Require-
ment ........................................................................
66
FUNCTION DIAGNOSIS ............................68
VDC ....................................................................68
Page 944 of 5121

BRC-3
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P System Diagram ......................................................
68
System Description .................................................68
Component Parts Location ......................................69
Component Description ...........................................70
TCS .....................................................................71
System Diagram ......................................................71
System Description .................................................71
Component Parts Location ......................................72
Component Description ...........................................73
ABS ....................................................................74
System Diagram ......................................................74
System Description .................................................74
Component Parts Location ......................................75
Component Description ...........................................76
EBD ....................................................................77
System Diagram ......................................................77
System Description .................................................77
Component Parts Location ......................................78
Component Description ...........................................79
DIAGNOSIS SYSTEM [ABS ACTUATOR
AND ELECTRIC UNIT (CONTROL UNIT)] ........
80
CONSULT-III Function ............................................80
COMPONENT DIAGNOSIS .........................85
C1101, C1102, C1103, C1104 WHEEL SEN-
SOR ....................................................................
85
Description ..............................................................85
DTC Logic ...............................................................85
Diagnosis Procedure ...............................................85
Component Inspection ............................................87
Special Repair Requirement ...................................87
C1105, C1106, C1107, C1108 WHEEL SEN-
SOR ....................................................................
88
Description ..............................................................88
DTC Logic ...............................................................88
Diagnosis Procedure ...............................................88
Component Inspection ............................................90
Special Repair Requirement ...................................90
C1109 POWER AND GROUND SYSTEM .........91
Description ..............................................................91
DTC Logic ...............................................................91
Diagnosis Procedure ...............................................91
Special Repair Requirement ...................................92
C1110, C1153, C1170 ABS ACTUATOR AND
ELECTRIC UNIT (CONTROL UNIT) ..................
93
DTC Logic ...............................................................93
Diagnosis Procedure ...............................................93
Special Repair Requirement ...................................93
C1111 ABS MOTOR, MOTOR RELAY SYS-
TEM ....................................................................
94
Description ..............................................................94
DTC Logic ...............................................................94
Diagnosis Procedure ...............................................94
Component Inspection .............................................95
Special Repair Requirement ....................................95
C1115 WHEEL SENSOR ..................................96
Description ...............................................................96
DTC Logic ................................................................96
Diagnosis Procedure ...............................................96
Component Inspection .............................................98
Special Repair Requirement ....................................98
C1116 STOP LAMP SWITCH ...........................99
Description ...............................................................99
DTC Logic ................................................................99
Diagnosis Procedure ...............................................99
Component Inspection .............................................99
Special Repair Requirement ..................................100
C1120, C1122, C1124, C1126 IN ABS SOL ...101
Description .............................................................101
DTC Logic ..............................................................101
Diagnosis Procedure .............................................101
Component Inspection ...........................................102
Special Repair Requirement ..................................102
C1121, C1123, C1125, C1127 OUT ABS SOL .103
Description .............................................................103
DTC Logic ..............................................................103
Diagnosis Procedure .............................................103
Component Inspection ...........................................104
Special Repair Requirement ..................................104
C1130 ENGINE SIGNAL .................................105
Description .............................................................105
DTC Logic ..............................................................105
Diagnosis Procedure .............................................105
Special Repair Requirement ..................................105
C1140 ACTUATOR RELAY SYSTEM ............106
Description .............................................................106
DTC Logic ..............................................................106
Diagnosis Procedure .............................................106
Component Inspection ...........................................107
Special Repair Requirement ..................................107
C1142 PRESS SENSOR .................................108
Description .............................................................108
DTC Logic ..............................................................108
Diagnosis Procedure .............................................108
Component Inspection ...........................................108
Special Repair Requirement ..................................109
C1143 STEERING ANGLE SENSOR .............110
Description .............................................................110
DTC Logic ..............................................................110
Diagnosis Procedure .............................................110
Component Inspection ...........................................111
Special Repair Requirement ..................................111
C1144 STEERING ANGLE SENSOR .............112
DTC Logic ..............................................................112
Page 945 of 5121

BRC-4
Diagnosis Procedure .............................................112
Special Repair Requirement ..................................112
C1145, C1146 YAW RATE/SIDE G SENSOR .113
Description .............................................................113
DTC Logic ..............................................................113
Diagnosis Procedure .............................................113
Component Inspection ...........................................114
Special Repair Requirement ..................................115
C1155 BRAKE FLUID LEVEL SWITCH ..........116
Description .............................................................116
DTC Logic ..............................................................116
Diagnosis Procedure .............................................116
Component Inspection ...........................................117
Special Repair Requirement ..................................117
C1164, C1165 CV SYSTEM ............................118
Description .............................................................118
DTC Logic ..............................................................118
Diagnosis Procedure .............................................118
Component Inspection ...........................................119
Special Repair Requirement ..................................119
C1166, C1167 SV SYSTEM .............................120
Description .............................................................120
DTC Logic ..............................................................120
Diagnosis Procedure .............................................120
Component Inspection ...........................................121
Special Repair Requirement ..................................121
U1000, U1002 CAN COMM CIRCUIT .............122
Description .............................................................122
DTC Logic ..............................................................122
Diagnosis Procedure .............................................122
Special Repair Requirement ..................................122
POWER SUPPLY AND GROUND CIRCUIT ...123
Description .............................................................123
Diagnosis Procedure .............................................123
PARKING BRAKE SWITCH ............................124
Component Function Check ..................................124
Diagnosis Procedure .............................................124
Component Inspection ...........................................124
VDC OFF SWITCH ..........................................126
Description .............................................................126
Component Function Check ..................................126
Diagnosis Procedure .............................................126
Component Inspection ...........................................127
ABS WARNING LAMP ....................................128
Description .............................................................128
Component Function Check ..................................128
Diagnosis Procedure .............................................128
BRAKE WARNING LAMP ...............................129
Description .............................................................129
Component Function Check ..................................129
Diagnosis Procedure .............................................129
VDC OFF INDICATOR LAMP ..........................130
Description ............................................................130
Component Function Check .................................130
Diagnosis Procedure .............................................130
SLIP INDICATOR LAMP ..................................131
Description ............................................................131
Component Function Check .................................131
Diagnosis Procedure .............................................131
ECU DIAGNOSIS ......................................132
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) .............................................
132
Reference Value ...................................................132
Wiring Diagram - BRAKE CONTROL SYSTEM - .136
Fail-Safe ................................................................139
DTC No. Index ......................................................140
SYMPTOM DIAGNOSIS ...........................142
EXCESSIVE ABS FUNCTION OPERATION
FREQUENCY ....................................................
142
Diagnosis Procedure .............................................142
UNEXPECTED PEDAL REACTION .................143
Diagnosis Procedure .............................................143
THE BRAKING DISTANCE IS LONG ..............144
Diagnosis Procedure .............................................144
ABS FUNCTION DOES NOT OPERATE .........145
Diagnosis Procedure .............................................145
PEDAL VIBRATION OR ABS OPERATION
SOUND OCCURS .............................................
146
Diagnosis Procedure .............................................146
VEHICLE JERKS DURING VDC/TCS/ABS
CONTROL ........................................................
147
Diagnosis Procedure .............................................147
NORMAL OPERATING CONDITION ...............148
Description ............................................................148
PRECAUTION ...........................................149
PRECAUTIONS ................................................149
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
149
Precaution for Procedure without Cowl Top Cover .149
Precaution for Brake System ................................149
Precaution for Brake Control .................................150
Precautions for Harness Repair ............................150
ON-VEHICLE REPAIR ..............................151
WHEEL SENSOR .............................................151
FRONT WHEEL SENSOR ......................................151
FRONT WHEEL SENSOR : Exploded View .........151
Page 946 of 5121

BRC-5
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P FRONT WHEEL SENSOR : Removal and Instal-
lation ......................................................................
151
REAR WHEEL SENSOR .........................................152
REAR WHEEL SENSOR : Exploded View ...........152
REAR WHEEL SENSOR : Removal and Installa-
tion ........................................................................
152
SENSOR ROTOR .............................................153
FRONT SENSOR ROTOR .......................................153
FRONT SENSOR ROTOR : Exploded View .........153
FRONT SENSOR ROTOR : Removal and Instal-
lation ......................................................................
153
REAR SENSOR ROTOR .........................................153
REAR SENSOR ROTOR : Exploded View ...........153
REAR SENSOR ROTOR : Removal and Installa-
tion .........................................................................
153
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) ...........................................
154
Exploded View .......................................................154
Removal and Installation .......................................154
YAW RATE/SIDE G SENSOR ........................156
Exploded View .......................................................156
Removal and Installation .......................................156
STEERING ANGLE SENSOR .........................157
Exploded View .......................................................157
Removal and Installation .......................................157
Page 950 of 5121
![NISSAN TEANA 2008 Owners Manual ABS
BRC-9
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
FUNCTION DIAGNOSIS
ABS
System DiagramINFOID:0000000003766722
System DescriptionINFOID:0000000003766723
Anti-Lock Braking System NISSAN TEANA 2008 Owners Manual ABS
BRC-9
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
FUNCTION DIAGNOSIS
ABS
System DiagramINFOID:0000000003766722
System DescriptionINFOID:0000000003766723
Anti-Lock Braking System](/img/5/57391/w960_57391-949.png)
ABS
BRC-9
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
FUNCTION DIAGNOSIS
ABS
System DiagramINFOID:0000000003766722
System DescriptionINFOID:0000000003766723
Anti-Lock Braking System detects wheel revolution while braking, electronically controls braking force, and
prevents wheel locking during sudden braking. It improves handling stability and maneuverability for avoid-
ing obstacles.
Electrical system diagnosis by CONSULT-III is available.
JSFIA0257GB
Page 951 of 5121
![NISSAN TEANA 2008 Owners Manual BRC-10
< FUNCTION DIAGNOSIS >[ABS]
ABS
Component Parts Location
INFOID:0000000003766724
Component DescriptionINFOID:0000000003766725
1. ABS warning lamp 2. Brake warning lamp 3.ABS actuator and electr NISSAN TEANA 2008 Owners Manual BRC-10
< FUNCTION DIAGNOSIS >[ABS]
ABS
Component Parts Location
INFOID:0000000003766724
Component DescriptionINFOID:0000000003766725
1. ABS warning lamp 2. Brake warning lamp 3.ABS actuator and electr](/img/5/57391/w960_57391-950.png)
BRC-10
< FUNCTION DIAGNOSIS >[ABS]
ABS
Component Parts Location
INFOID:0000000003766724
Component DescriptionINFOID:0000000003766725
1. ABS warning lamp 2. Brake warning lamp 3.ABS actuator and electric unit (con-
trol unit)
4. Front wheel sensor 5. Rear wheel sensor
A. Combination meter B. Engine room right side C. Steering knuckle
D. Rear axle
JSFIA0258ZZ
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-25, "
Description"Motor
Actuator relay (main relay)BRC-36, "
Description"
Solenoid valveBRC-32, "Description"
Wheel sensorBRC-16, "Description"
ABS warning lampBRC-40, "Description"
Brake warning lampBRC-41, "Description"