display NISSAN TEANA 2008 Service Manual

DEF-56
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000003940044
NOTE:
The details of time display are as follows.
 CRNT: A malfunction is detected now.
 PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data and IGN Counter, refer to
DEF-8, "
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
4 B2013: ID DISCORD BCM-S/L
 B2014: CHAIN OF S/L-BCM
 B2553: IGNITION RELAY
 B2555: STOP LAMP
 B2556: PUSH-BTN IGN SW
 B2557: VEHICLE SPEED
 B2560: STARTER CONT RELAY
 B2601: SHIFT POSITION
 B2602: SHIFT POSITION
 B2603: SHIFT POSI STATUS
 B2604: PNP SW
 B2605: PNP SW
 B2606: S/L RELAY
 B2607: S/L RELAY
 B2608: STARTER RELAY
 B2609: S/L STATUS
 B260A: IGNITION RELAY
 B260B: STEERING LOCK UNIT
 B260C: STEERING LOCK UNIT
 B260D: STEERING LOCK UNIT
 B260F: ENG STATE SIG LOST
 B2612: S/L STATUS
 B2614: ACC RELAY CIRC
 B2615: BLOWER RELAY CIRC
 B2616: IGN RELAY CIRC
 B2617: STARTER RELAY CIRC
 B2618: BCM
 B2619: BCM
 B261A: PUSH-BTN IGN SW
 B261E: VEHICLE TYPE
 B26E1: ENG STATE NO RES
 B26E9: S/L STATUS
 B26EA: KEY REGISTRATION
 U0415: VEHICLE SPEED SIG
5 B2621: INSIDE ANTENNA
 B2622: INSIDE ANTENNA
 B2623: INSIDE ANTENNA Priority DTC
CONSULT display Fail-safe Freeze Frame DataIntelligent Key warn-
ing lamp ONReference page
No DTC is detected.
further testing
may be required.————
U1000: CAN COMM CIRCUIT — — —BCS-33
U1010: CONTROL UNIT (CAN) — — —BCS-34
U0415: VEHICLE SPEED SIG — — —BCS-35
B2013: ID DISCORD BCM-S/L××—SEC-46
B2014: CHAIN OF S/L-BCM××—SEC-47
B2190: NATS ANTENNA AMP×——SEC-39
B2191: DIFFERENCE OF KEY×——SEC-42

BCM (BODY CONTROL MODULE)
DEF-57
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
DEF
N
O
P
B2192: ID DISCORD BCM-ECM×——SEC-43
B2193: CHAIN OF BCM-ECM×——SEC-45
B2553: IGNITION RELAY —×—PCS-49
B2555: STOP LAMP —×—SEC-50
B2556: PUSH-BTN IGN SW —××SEC-52
B2557: VEHICLE SPEED×××SEC-54
B2560: STARTER CONT RELAY×××SEC-55
B2562: LOW VOLTAGE —×—BCS-36
B2601: SHIFT POSITION×××SEC-56
B2602: SHIFT POSITION×××SEC-59
B2603: SHIFT POSI STATUS×××SEC-61
B2604: PNP SW×××SEC-64
B2605: PNP SW×××SEC-67
B2606: S/L RELAY×××SEC-69
B2607: S/L RELAY×××SEC-70
B2608: STARTER RELAY×××SEC-72
B2609: S/L STATUS×××SEC-74
B260A: IGNITION RELAY×××PCS-51
B260B: STEERING LOCK UNIT —××SEC-78
B260C: STEERING LOCK UNIT —××SEC-79
B260D: STEERING LOCK UNIT —××SEC-80
B260F: ENG STATE SIG LOST×××SEC-81
B2612: S/L STATUS×××SEC-85
B2614: ACC RELAY CIRC —××PCS-53
B2615: BLOWER RELAY CIRC —××PCS-55
B2616: IGN RELAY CIRC —××PCS-57
B2617: STARTER RELAY CIRC×××SEC-89
B2618: BCM×××PCS-59
B2619: BCM×××SEC-91
B261A: PUSH-BTN IGN SW —××SEC-92
B261E: VEHICLE TYPE××× (Turn ON for 15
seconds)SEC-95
B2621: INSIDE ANTENNA —×—DLK-50
B2622: INSIDE ANTENNA —×—DLK-52
B2623: INSIDE ANTENNA —×—DLK-54
B26E1: ENG STATE NO RES×××SEC-82
B26E9: S/L STATUS××× (Turn ON for 15
seconds)SEC-83
B26EA: KEY REGISTRATION —×× (Turn ON for 15
seconds)SEC-84
CONSULT display Fail-safe Freeze Frame DataIntelligent Key warn-
ing lamp ONReference page

ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER
SWITCH BUT IT OPERATES
DEF-61
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
DEF
N
O
P
ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER
SWITCH BUT IT OPERATES
WITH AV CONTROL UNIT
WITH AV CONTROL UNIT : Diagnosis ProcedureINFOID:0000000003806069
1.CHECK AV CONTROL FUNCTION
Check that the AV control unit is operating normally.
 Base audio: Refer to AV-45, "
Work Flow".
 BOSE audio with navigation: Refer to AV-398, "
Work Flow".
 BOSE audio without navigation: Refer to AV-185, "
Work Flow".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.
WITHOUT AV CONTROL UNIT
WITHOUT AV CONTROL UNIT : Diagnosis ProcedureINFOID:0000000003888342
1.CHECK A/C CONTROL FUNCTION
Check that the A/C control is operating normally.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check A/C control system. Refer to HAC-6, "
Work Flow".
2.CHECK REAR WINDOW DEFOGGER DISPLAY
Check that ON appears on the display when rear window defogger is activated.
Is the inspection result normal?
YES >> Replace A/C control (rear window defogger switch). Refer to VTL-21, "Removal and Installation".
NO >> Check rear window defogger indicator. Refer to DEF-62, "
WITHOUT AV CONTROL UNIT : Diag-
nosis Procedure".

DLK-3
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P Description ..............................................................
80
Component Function Check ..................................80
Diagnosis Procedure ...............................................80
INTELLIGENT KEY WARNING BUZZER ..........82
Description ..............................................................82
Component Function Check ..................................82
Diagnosis Procedure ...............................................82
Component Inspection ............................................83
INTELLIGENT KEY ............................................84
Description ..............................................................84
Component Function Check ..................................84
Diagnosis Procedure ...............................................84
Component Inspection ............................................84
Special Repair Requirement ...................................85
KEY SLOT ..........................................................86
Description ..............................................................86
Component Function Check ..................................86
Diagnosis Procedure ...............................................86
Component Inspection ............................................87
KEY SLOT ILLUMINATION ...............................88
Description ..............................................................88
Component Function Check ..................................88
Diagnosis Procedure ...............................................88
Component Inspection ............................................89
HORN FUNCTION ..............................................91
Description ..............................................................91
Component Function Check ..................................91
Diagnosis Procedure ..............................................91
COMBINATION METER DISPLAY FUNC-
TION ...................................................................
93
Description ..............................................................93
Component Function Check ..................................93
Diagnosis Procedure ...............................................93
BUZZER (COMBINATION METER) ...................94
Description ..............................................................94
Component Function Check ..................................94
Diagnosis Procedure ...............................................94
KEY WARNING LAMP .......................................95
Description ..............................................................95
Component Function Check ..................................95
Diagnosis Procedure ...............................................95
HAZARD FUNCTION .........................................96
Description ..............................................................96
Component Function Check ..................................96
Diagnosis Procedure ...............................................96
POWER DOOR LOCK SYSTEM ........................97
Wiring Diagram - POWER DOOR LOCK SYSTEM
- ...............................................................................
97
INTELLIGENT KEY SYSTEM ..........................104
Wiring Diagram - INTELLIGENT KEY SYSTEM - ..104
TRUNK LID OPENER .....................................116
Wiring Diagram - TRUNK LID OPENER - .............116
FUEL FILLER LID OPENER ...........................119
Wiring Diagram - FUEL LID OPENER - ................119
ECU DIAGNOSIS .......................................121
BCM (BODY CONTROL MODULE) ...............121
Reference Value ....................................................121
Wiring Diagram - BCM - ........................................144
Fail-safe .................................................................150
DTC Inspection Priority Chart .............................152
DTC Index .............................................................153
SYMPTOM DIAGNOSIS ............................155
DOOR DOES NOT LOCK/UNLOCK WITH
DOOR LOCK AND UNLOCK SWITCH ..........
155
ALL DOOR ...............................................................155
ALL DOOR : Diagnosis Procedure ........................155
DRIVER SIDE ...........................................................155
DRIVER SIDE : Diagnosis Procedure ...................155
PASSENGER SIDE ..................................................155
PASSENGER SIDE : Diagnosis Procedure ..........156
REAR LH ..................................................................156
REAR LH : Diagnosis Procedure ...........................156
REAR RH .................................................................156
REAR RH : Diagnosis Procedure ..........................156
VEHICLE SPEED SENSING AUTO LOCK
OPERATION DOES NOT OPERATE .............
157
Diagnosis Procedure .............................................157
DOOR DOES NOT LOCK/UNLOCK WITH IN-
TELLIGENT KEY ............................................
158
Description .............................................................158
Diagnosis Procedure .............................................158
HAZARD AND HORN REMINDER DOES
NOT OPERATE ...............................................
159
Description .............................................................159
Diagnosis Procedure .............................................159
AUTO DOOR LOCK OPERATION DOES NOT
OPERATE .......................................................
160
Description .............................................................160
Diagnosis Procedure .............................................160
DOOR DOES NOT LOCK/UNLOCK WITH
DOOR REQUEST SWITCH ............................
161
DRIVER SIDE ...........................................................161
DRIVER SIDE : Description ...................................161
DRIVER SIDE : Diagnosis Procedure ...................161
PASSENGER SIDE ..................................................161
PASSENGER SIDE : Description ..........................161

DLK-8
< BASIC INSPECTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
1.GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.CHECK DTC
1. Check DTC for BCM.
2. Perform the following procedure if DTC is displayed.
- Record DTC and freeze frame data (print them out with CONSULT-III).
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
At this time, always connect CONSULT-III to the vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to DLK-152, "
DTCInspectionPriorityChart" (BCM) determine trou-
ble diagnosis order.
NOTE:
Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation
Procedure.
Is DTC detected?
YES >> GO TO 7.
NO >> Refer to GI-35, "
Intermittent Incident".
6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 7.
7.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.

DIAGNOSIS AND REPAIR WORKFLOW
DLK-9
< BASIC INSPECTION >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is malfunctioning part detected?
YES >> GO TO 8.
NO >> Check voltage of related BCM terminals using CONSULT-III.
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 9.
9.FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction has been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 7.
YES (Symptom remains)>>GO TO 6.
NO >>INSPECTION END

INTELLIGENT KEY SYSTEM
DLK-31
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
WARNING FUNCTION
WARNING FUNCTION : System DescriptionINFOID:0000000003794756
OPERATION DESCRIPTION
The warning function are as per the following and are given to the user as warning information and warnings
using combinations of Intelligent Key warning buzzer, KEY warning lamp, key slot illumination and information
display in combination meter.
 Intelligent Key system malfunction
 OFF position warning
 P position warning
 ACC warning
 Take away warning
 Door lock operation warning
 Key warning
 Intelligent Key insert information
 Engine start information
 Steering lock information
 Intelligent key low battery warning
 Key ID warning
OPERATION CONDITION
Once one of the following conditions below is established, alert or warning will be executed.
10. Inside key antenna (instrument cen-
ter) M10511. Inside key antenna (trunk room) B86 12. Outside key antenna (rear bumper)
D85
13. Front outside handle LH (request
switch) D1114. Front outside handle LH
(outside key antenna) D1215. Trunk lid lock assembly
(trunk lid opener actuator) T5
16. Front door switch (driver side) B34
A. Behind the combination meter B. Engine room (LH) C. Behind the instrument lower panel
RH
D. Behind the center console E. Behind the audio unit F. View with rear bumper removed
1. Front door lock assembly (driver
side) D92. Rear door lock assembly LH D85 3. Trunk lid opener request switch T6
A. View with front door finisher removed B. View with rear door finisher removed C. View with trunk lid
JMKIA2376ZZ
Warning/Information functions Operation procedure
Intelligent Key system malfunction When a malfunction is detected in BCM, “KEY” warning lamp will illuminate.

DLK-32
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY SYSTEM
WARNING METHOD
The following table shows the alarm or warning methods with chime.
Information display (combination meter), “KEY” indicator or key slot illumination when the warning conditions
are met.
OFF position warning For internal Ignition switch: ACC position.
 Door switch (driver side): ON (Door is open).
For externalOFF position warning (for internal) is in active mode, driver side door is closed.
NOTE:
OFF position (for external) active only when each of the sequence has oc-
curred as per the following: P position warning → ACC warning → OFF posi-
tion warning (for internal) → OFF position warning (for internal)
P position warning Shift position: Any position except the P position.
 Engine is running to stopped (ignition switch is ON to OFF).
ACC warning When P position warning is in active mode, shift position changes from the
P position.
 Ignition switch: ACC position.
Ta k e a w a y w a r n i n gDoor is open to close Ignition switch: Any position except the LOCK position.
 Door switch: ON to OFF (door is open to close).
 Intelligent Key can not be detected inside the vehicle.
Door is open Door switch: ON (door is open).
 Key ID verification every 5 seconds when registered Intelligent Key can not
be detected inside the vehicle.
Push button-ignition
switch operation Ignition switch: Any position except the LOCK position.
 Press push-button ignition switch.
 Intelligent Key can not be detected inside the vehicle.
Intelligent Key is removed
from key slotWhen Intelligent Key is removed from key slot, Intelligent Key can not be de-
tected inside the vehicle.
Door lock operation warn-
ingRequest switch operationWhen request switch is pushed (lock operation) under the following conditions.
 All doors are closed.
 All doors are unlocked.
 Intelligent Key is inside vehicle.
Intelligent Key button op-
erationWhen Intelligent Key button is pushed (lock operation) under the following con-
ditions.
 Door switch: ON (any door is open).
 For 3 seconds after Intelligent Key is removed from key slot.
Key warning Ignition switch is in the OFF position.
 Driver side door switch: ON (driver side door is open).
 Intelligent Key is inserted in key slot.
Intelligent Key insert information Door switch: ON to OFF (door is open to close).
 Ignition switch: OFF to ON position.
 Intelligent Key is out of key slot.
 Intelligent Key can not be detected inside the vehicle.
Engine start informationIgnition switch is in the
ON position Ignition switch: ON position.
 Shift position: P position.
 Engine is stopped.
Ignition switch is in any
position except the ON
position Ignition switch: Any position except the ON position.
 Shift position: P position.
 Intelligent Key is inserted in key slot or Intelligent Key can be detected inside
the vehicle.
Steering lock information When steering lock can not be released after ignition switch is turned ON.
Intelligent Key low battery warningWhen Intelligent Key is battery low, BCM is detected after ignition switch is
turned ON.
Key ID warningWhen registered Intelligent Key can not be detected inside the vehicle after ig-
nition switch is turned ON. Warning/Information functions Operation procedure

INTELLIGENT KEY SYSTEM
DLK-33
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Warning/Information functions“KEY” warn-
ing lampInformation display
(combination meter)Key slot il-
luminationWarning chime
Combination
meter buzzerIntelligent
Key warning
buzzer
Intelligent Key system malfunction Illuminate — — — —
OFF position warn-
ing For internal — — — Activate —
For external — — — — Activate
P position warning — — Activate —
ACC warning — — — —
Ta k e a w a y w a r n i n gDoor is open to
close— Blink Activate Activate
Door is open — Flash — —
Push-ignition
switch operation—FlashActivate—
Intelligent Key is
removed from
key slot—Flash——
Door lock operation
warningRequest switch
operation————Activate
Intelligent Key
operation————Activate
Key ID warning — — — —
Key warning — Flash Activate —
JMKIA0037GB
JMKIA0047GB
JMKIA0036GB
JMKIA0036GB
JMKIA0035GB

DLK-34
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY SYSTEM
LIST OF OPERATION RELATED PARTS
Parts marked with × are the parts related to operation.
Intelligent Key insert information — Flash — —
Engine start information — — — —
Steering lock information — — — —
Intelligent Key low battery warning — — — —Warning/Information functions“KEY” warn-
ing lampInformation display
(combination meter)Key slot il-
luminationWarning chime
Combination
meter buzzerIntelligent
Key warning
buzzer
JMKIA0034GB
JMKIA0032GB
JMKIA0033GB
JMKIA0048GB
Warning function
Intelligent Key
Key slot
Ignition switch
Door switch
Door request switch
Inside key antenna
Outside key antenna
Intelligent Key warning buzzer
Combination meter warning buzzer
CAN communication system
BCM
Combination meter display
Key slot illumination
Park position switch
“KEY” warning lamp
Intelligent Key system malfunction×× ×
OFF position warningFor internal× ×××
For external×××
P position warning× ×××× ×
ACC warning× ×××× ×